TRIPLETT MS300 Pinless Moisture Meter User Manual
- June 5, 2024
- TRIPLETT
Table of Contents
TRIPLETT MS300 Pinless Moisture
Introduction
The MS300 sensor performs non-invasive, relative moisture measurements on wood and building materials such as wallboard, sheet rock, cardboard, plaster, concrete, and mortar. The MS300 also offers auto power off (APO), display lock (hold), and self-calibration features. The MS300 is ideal for building restoration projects and applications where moisture detection on floors and under carpets is critical. The MS300 is also a handy tool for analyzing the effects of water leakage behind walls and in ceilings.
Measurement Considerations
To measure moisture, the MS300 sensor emits and senses low-power electro- magnetic signals. The displayed reading in percent is an average of the moisture content measured over the entire non-destructive spherical sensor. The maximum depth of penetration is 4.0” (102mm) Moisture that is closer to the surface has a greater effect on the displayed average than the moisture nearer to the maximum depth of penetration. Placing the sensor on a surface whose thickness is less than the maximum depth of penetration may result in unreliable moisture readings; in these cases, you can stack material on top of the measured surface to increase the thickness. The MS300 also produces audible tones and moisture droplet display icons to indicate moisture level. The audible tone rate and number of droplets increase as the moisture level increases. The MS300 also produces audible tones and ‘moisture droplet’ display icons to indicate moisture level. The audible tone rate and number of droplets increase as the moisture level increases.
Meter Description
- LCD Display
- Power button
- Display Lock/Beeper button
- Material Select button
- Sensor Ball Probe
Display Description
- Moisture Drop icons one for low moisture two for medium, and three for high.
- Wood mode
- Building Material mode
- Beeper active icon
- Moisture reading
- Digital reading in % relative
- Display Lock Mode
- Battery Status
Operation
Powering the Meter and Self Calibration
Long press the power button to switch the meter on/off. The meter beeps and displays ON as it powers up. If the meter does not switch on, please check the battery. The meter emits audible tones and performs a self-calibration upon start-up. Keep the measurement sensor at least 8 to 10 cm 3 to 4 from hands and objects during calibration. The calibration reading must not exceed 0.5. If so recalibrate ensuring that hands or other objects are clear of the sensor. Note: Calibrate the meter whenever moving from one measurement area to another.
Auto Power OFF
The meter will automatically power OFF if the reading stays 0% for 3 minutes. If the meter detects readings, other than 0%, it will not automatically power OFF.
Display Hold Lock
Short press the Display Lock button to freeze the displayed reading. The icon is visible on the display when Display Lock is active. Press again to return to the normal operating mode.
Beeper ON/OFF
The beeper defaults to ON. To switch the beeper OFF, long press the Display Lock/Audible Beeper button . When the beeper is active, the audio display icon will be visible.
Pinless Moisture Measurements
- Short press the Material Select button () to toggle the Wood and Building Material modes.
- The displayed icons indicate the selected mode.
- Position the sensor firmly on a flat surface so that it directly touches the measurement area.
- The measurement surface area should be larger than the sensor surface area.
- Observe the displayed relative readings, view the displayed moisture droplet icons more drops indicate higher moisture levels and listen for the audible beeping faster beeping indicates higher moisture; there are eight intensity levels.
- the displayed reading is an average of the moisture measured over the entire sensor surface area to the maximum penetration depth.
- The section Relative Moisture Reading Ranges, below, provides measurement and droplet icon ranges.
Relative Moisture Reading Ranges
Maintenance
Battery Replacement
When the battery status icon appears empty or flashing, replace the battery.
- Remove the rear battery cover by pushing the compartment latch bottom, back of meter.
- Replace the 9V battery observing correct polarity.
- Replace the battery cover securely.
- Dispose of battery responsibly and within applicable legal regulations.
- Never dispose of used batteries or rechargeable batteries in household waste.
- As consumers, users are legally required to take used batteries to appropriate collection sites, the retail store where the batteries were purchased, or wherever batteries are sold.
Disposal
Do not dispose of this instrument in household waste. The user is obligated to
take end-of-life devices to a designated collection point for the disposal of
electrical and electronic equipment.
Care and Cleaning
Store the meter in an environmentally stable, dust free environment, out of direct sunlight. Remove the battery from the instrument if the meter is to be stored for long periods or if the battery power symbol appears empty or flashing on the display. To clean the meter case, wipe with a damp cloth, do not use solvents or abrasives.
Specifications
- Display :LCD with multi function indicators
- Measurement Type: Pinless, non-destructive
- Measurement Indication :Digital relative reading in %, moisture drop icons (1, 2, or 3 droplets) audible tone (8 intensity levels) indicating low to high moisture readings
- Measurement Ranges: Wood: Low: 0.1% to 16.9
- Medium: 17.0% to 39.9%
- High: 40.0 to 99.9%
- Building Materials:
- Low: 0.1% to 16.9%
- Medium: 17.0% to 39.9%
- High: 40.0 to 99.9%
- Measurement depth Sensor detects to a depth of 102mm (4.0)
- Resolution :0.1%
- Accuracy :Relative readings only
- Auto Power OFF display reading:After approx three (3) minutes with a 0%
- Power Supply :One (1) 9V battery, battery consumption: < 40mA
- Low Battery approximately: Indication < 7.5VDC
- Low Battery APO < 5.5VDC; APO will occur in 20 seconds, approximately
- Operating Conditions: 5 ~ 45oC (41 ~ 113oF); 80%RH max.
- Storage Conditions: 0 ~ 50oC (32 ~ 122oF); 85%RH max.
- Dimensions: 210 x 65 x 30mm (8.3 x 2.6 x 1.2)
- Weight: 160g 5.6 oz without battery
Warranty
Triplett / Jewell Instruments extends the following warranty to the original
purchaser of these goods for use. Triplett warrants to the original purchaser
for use that the products sold by it will be free from defects in workmanship
and material for a period of (1) one year from the date of purchase. This
warranty does not apply to any of our products which have been repaired or
altered by unauthorized persons in any way or purchased from unauthorized
distributors so as, in our sole judgment, to injure their stability or
reliability, or which have been subject to misuse, abuse, misapplication,
negligence, accident or which have had the serial numbers altered, defaced, or
removed. Accessories, including batteries are not covered by this warranty
www.triplett.co
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>