TRIPLETT HVD132 Non Contact High AC Voltage Detector User Manual

TRIPLETT HVD132 Non Contact High AC Voltage Detector

Specifications:

• Model: HVD132
• Type: Non-Contact High AC Voltage Detector
• Power Consumption:
  • OFF: Less than 5A
  • Low Voltage Detection Mode: Less than 40mA
  • High Voltage Detection Mode: Less than 40mA
• Ranges:
  • Low: 50V~1.5kV
  • High: 1.5kV~132kV

Product Usage Instructions

Safety Precautions:
Before using the Non-Contact High Voltage Detector, ensure you have read and understood the safety precautions outlined in the manual.

Applications :

• Non-contact detection of live voltages
• Find faults in cables
• Check and detect live high voltage cables
• Trace live wires
• Check high frequency radiation
• Check grounding equipment
• Detect residual or induced voltages

Operation :

1. Power ON/OFF function: Press the ON/OFF button to power on the detector. Two red LEDs will flash, and the buzzer will generate a sound intermittently.
2. Circuit Test function: Press the TEST button to ensure the whole circuit is working well before testing actual high voltage circuits.
3. Ranges Selection: Use the LOW button for voltages between 50V~1.5kV and the HIGH button for voltages between 1.5kV~132kV.

Maintenance:
Examine the detector to ensure it is clean and dry before each use. Wipe with a clean, dry, lint-free cloth if necessary.

FAQ:

• Q: What should I do if the detector does not power on?
  A: Check the battery and ensure it is properly installed. If the issue persists, contact customer support for assistance.

• Q: Can the detector be used for low voltage detection only?
  A: No, the detector can be used for both low and high voltage detection by selecting the appropriate range.

User Manual
HVD132
Non-Contact High AC Voltage Detector

Introduction

• NOTE
  This detector has been designed and tested according to CE Safety Requirements for Electronic Measuring Apparatus. Follow all warnings to ensure safe operation.

• WARNING
  READ “SAFETY PRECAUTION” (NEXT PAGE) BEFORE USING THE HIGH VOLTAGE DETECTOR.

Safety precaution

• Electricity can cause severe injuries with high voltages. Therefore it is very important to read the following info before using the Non-contact High Voltage Detector.
• This must only be used and operated by a competent trained person and in strict accordance with the instructions. We will not accept liability for any damage or injury caused by misuse or non compliance with instructions and safety procedures.
• Examine the Non-contact High Voltage Detector to make sure it is clean and dry. If it is not, wipe with a clean, dry, lint-free cloth.
• The high voltage detector test should always be used as an indication only.
• Read all safety information carefully before attempting to operate or service the High Voltage Detector.
• Use the High Voltage Detector only as specified in this manual. Otherwise, the protection provided by the High Voltage Detector may be impaired.
• Please keep in your mind to wear high insulated gloves when you test high voltages between 600V~1.5kV.
• Please keep in your mind to wear high insulated gloves and to use the HVD132 when you test high voltages between 1.5kV~132kV.

Applications

• Non-contact detection of live voltages
• Find faults in cables
• Check and detect live high voltage cables
• Trace live wires
• Check high frequency radiation
• Check grounding equipment
• Detect residual or induced voltages

Features & specifications

• Power ON/OFF function
• Circuit Test function
• Press the Test button to make sure the whole circuit is working well before testing actual high voltage circuits.
• 2 ranges for selection (2 function buttons)
  • Low : 50V~1.5kV
  • Press the LOW button, HVD132 is ready for low voltage detection.
  • HIGH : 1.5kV~132kV
  • Press the HIGH button, HVD132 is ready for high voltage detection.
• Power consumption
  • OFF : Less than 5μA
  • Low voltage detection mode : Less than 40mA High voltage detection mode : Less than 40mA
• Duty cycle : Continuous
• Response Time : Instantaneous
• Operating temperature : 0~50°C
• Power source : Alkaline battery 9V x 1
• Dimensions : 318(L) x 75(W) x 71(D) mm
• Weight : Approx. 227g (Battery included)
• Accessories
  • Instruction manual
  • Carry case
  • Battery

Instrument layout

1. Voltage sensor
2. TEST button
3. ON/OFF button
4. LOW range button
5. HIGH range button
6. LOW range LED
7. HIGH range LED
8. The connection point of Hot Stick
9. Battery cover
10. Red LEDs for detection

Operation

• ON/OFF button
  When POWERED ON, the 2 red LEDs will Flash and the buzzer will generate a sound intermittently. The red LED of the HIGH range will be turned on. The original mode is the HIGH range.

• TEST button
  Press the TEST button to do the self-test first, this is to make sure the circuits inside the HVD132 is ok. When you press the TEST button, the 2 red LEDs will glow and the buzzer will generate a sound continuously. The red LED of the HIGH range will be still on (the original mode). If the 2 red LEDs do not glow and the continuous sound doesn’t be generated, please replace with a new battery.

• LOW range button (Low voltage detection)

  • Press the ON/OFF button to turn on the high voltage detector.
  • Press the LOW range button, the 2 red LEDs will flash and the buzzer will generate a sound intermittently. The red LED of the LOW range will be turned on.
  • The LOW range for low voltage detection : 50V~1.5kV. Place the probe sensing tip of the high voltage detector near a low voltage line (50V~1.5kV), but not touching the line.
  • The red LEDs will flash very fast and the frequency of the sound will be at the same rate if a voltage is present.
  • When the probe sensing tip makes contact or is very close to the voltage line, the red LEDs will glow and the sound will last continuously.

• HIGH range (High voltage detection)

  • Press the ON/OFF button to turn on the high voltage detector.
  • The 2 red LEDs will flash and the buzzer will generate a sound intermittently. The red LED of the HIGH range will be turned on.
  • The original mode is the HIGH range for high voltage detection: 1.5kV~132kV.
  • Place the probe sensing tip of the high voltage detector near a high voltage source (1.5kV~132kV), but not touching the high voltage source.
  • The red LEDs will flash very fast and the frequency of the sound will be at the same rate if a high voltage is present.
  • When the probe sensing tip is getting closer to the High voltage source, the red LEDs will glow and the sound will last continuously.

Maintenance

Battery replacement

1. Unscrew the battery cover on the rear with a screwdriver, then slide the battery cover off the tester.
2. Take out the battery.
3. Replace with a new battery (9V).
4. Reinstall the battery cover and fasten the cover screws.

Cleaning and storage

WARNING
To avoid electrical shock or damage to the detector, do not get water inside the case.

1. Periodically wipe the case with a damp cloth and detergent; do not use abrasives or solvents.
2. If the detector is not used for periods of longer than 60 days, remove the battery and store

Warranty

Triplett / Jewell Instruments extends the following warranty to the original purchaser of these goods for use. Triplett warrants to the original purchaser for use that the products sold by it will be free from defects in workmanship and material for a period of (2) two years from the date of purchase. This warranty does not apply to any of our products which have been repaired or altered by unauthorized persons in any way or purchased from unauthorized distributors so as, in our sole judgment, to injure their stability or reliability, or which have been subject to misuse, abuse, misapplication, negligence, accident or which have had the serial numbers altered, defaced, or removed. Accessories, including batteries are not covered by this warranty.

Copyright © 2023 Triplett
www.triplett.com

References

• Triplett Test Equipment & Tools for Industrial & Electronics Solutions

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>