SEALEY LED113.V2 SMD LED Extra Slim Floodlight with Wall Bracket Instruction Manual

SEALEY LED113.V2 SMD LED Extra Slim Floodlight with Wall Bracket

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble-free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

• Refer to instructions

SAFETY

ELECTRICAL

WARNING! It is the user’s responsibility to read, understand and comply with the following:

• THIS PRODUCT MUST BE INSTALLED BY A QUALIFIED ELECTRICIAN.
• You must check all electrical equipment and appliances to ensure they are safe before using. You must inspect power supply leads and all electrical connections for wear and damage.
• You must ensure the risk of electric shock is minimized by the installation of appropriate safety devices.
• You must also read and understand the following instructions concerning electrical safety.
• Ensure the light is connected to the appropriate electrical on/off switch.
• Ensure the insulation on all cables and the product itself is safe before connecting to the main power supply.
• Ensure that cables are always protected against short circuits and overload.
• Regularly inspect power supply, leads, and all electrical connections for wear and damage, especially power connections, to ensure that none are loose.
• Ensure the voltage marked on the product is the same as the electrical power supply to be used.
• DO NOT pull the power cable once installed.
• DO NOT use worn or damaged leads or connections. Immediately replace or have repaired by a qualified Electrician.
• Ensure the unit is correctly earthed and wired according to the following. (Installation should be undertaken by a qualified electrician)
• Connect the green/yellow earth wire to the earth terminal ‘E’.
• Connect the brown live wire to live terminal ‘L’.
• Connect the blue neutral wire to the neutral terminal ‘N’.
• After wiring, check there are no bare wires, and that all wires have been correctly connected.

GENERAL SAFETY

• WARNING! Turn off the main power supply before servicing or performing any maintenance.
• Maintain the light in good condition (Repairs must only be undertaken by a qualified electrician).
• Replace or repair damaged parts. Use genuine parts only, nonauthorised parts may be dangerous and will invalidate the warranty.
• Ensure the light is installed correctly in accordance with these instructions.
• Only install the light on a vertical surface.
• DO NOT fi x the light on any horizontal surface i.e. ceiling, or overhang.
• Ideally the Installation should be away from fl ammable or combustible materials such as wood, cloth, paper, etc.
• DANGER! DO NOT direct the light into a person’s eyes. This unit has a very intensive light output, which if incorrectly used could cause eye damage.
• DO NOT install the light where it is likely to be knocked or hit.
• DO NOT install in bathrooms, shower rooms, saunas,s or such locations.
• DO NOT install near an exhaust outlet. i.e. boiler flue, dryer outlet, etc.
• DO NOT use the light without the front glass shield fitted.

INTRODUCTION

Mounted in die-cast powder coated aluminum extra slim housing with wall bracket. SMD LED technology allows ultra-bright illumination whilst still keeping costs lower than traditional halogen tubes. Even spread of light across a 110° angle. Supplied with power cable at 75cm only and suitable for outdoor mounting.

SPECIFICATION

• Model No: …………………………………… LED112.V2 ……………………… LED113.V2 ……………………….LED115.V2
• Colour Temperature: ……………………………. 6500K ……………………………..6500K ………………………………6500K
• Dimensions (W x D x H): …….. 157 x 56 x 101mm …………….195 x 57 x 152mm ……………..235 x 57 x 191mm
• IP Rating: …………………………………………….. IP65 ………………………………..IP65 …………………………………IP65
• LED Type: …………………………………………… SMD ………………………………. SMD ………………………………..SMD
• Lumen Output: ……………………………………1900lm …………………………… 5200lm …………………………. 10,000lm
• PIR Motion Sensor: …………………………………..No …………………………………. No ………………………………….. No
• Power: …………………………………………………. 20W ………………………………..50W ……………………………….100W
• Supply: ……………………………………………….. 230V ……………………………….230V ………………………………..230V

ASSEMBLY

WARNING

• DO NOT connect the unit to the mains power supply before installation.

INSTALLATION

1. Give careful consideration to the position of the unit to ensure you obtain maximum benefit from the lighting range, and that an appropriate electrical power source can be provided.
2. An approximate appropriate mounting height from the ground is 2.5m. See fig.1.
3. This LED floodlight develops minimal heat and is not subject to the same mounting restrictions that apply to halogen lamps that become too hot to touch. We do however recommend that the floodlight should not be placed in cramped or restrictive positions and should be fixed at the following minimum distances between the light and any surface/object. See fig.2.

• 500mm minimum between the top of the light and any overhead surface, or objects, i.e. ceilings, and overhangs.
• 200mm between sides of light and wall/surfaces.
• 2 meters minimum between the front of the light and any object to be illuminated.
• Fix the light to a vertical surface with appropriate fixings.
• Ensure the lamp is connected to the mains by a qualified electrician.

MAINTENANCE

1. Clean the casing externally (not the glass) with a moist cloth.
2. DO NOT use solvents or abrasives to clean the light.
3. Avoid touching the glass shield as handling may reduce its serviceable life and cause the glass to crack. If necessary clean the glass shield with alcohol and a soft cloth. Undo the single screw without removing it to clean internally.
4. DO NOT use the light without the glass shield.
5. DO NOT use the light without the weather seals intact.

ENVIRONMENT PROTECTION

Recycle unwanted materials instead of disposing of them as waste. All tools, accessories, and packaging should be sorted, taken to a recycling center, and disposed of in a manner that is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

WEEE REGULATIONS

Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid waste authority for recycling information.

Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications, and component parts without prior notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call our technical team at technical@sealey.co.uk or 01284 757505.

Important: No Liability is accepted for incorrect use of this product.

Warranty

• The guarantee is 24 months from the purchase date, proof of which is required for any claim.

Sealey Group

• ADDRESS: Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
• TEL: 01284 757500
• 01284 703534
• sales@sealey.co.uk
• www.sealey.co.uk

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>