Schneider SCBD25B BEER DISPENSER Instruction Manual

BEER DISPENSER
SCBD25B

INSTRUCTION MANUAL

Please read these instructions carefully before using this appliance. Please keep these instructions for future reference.

INTRODUCTION

This is a household Beer dispenser with high quality and unique design. It brings the beer to the best temperature for cold storage (3 to 6°C) within 19-21 hours. The Beer dispenser will keep the pressurized 5L Keg cool for an almost indefinite period. We do, however, suggest that you initially cool your beer keg for at least 12 hours in your refrigerator before placing it into the Beer dispenser.

IMPORTANT SAFETY INSTRUCTION

Please read the instructions carefully before using this product. Incorrect operation may cause injury to people and property. Please save the instructions to a safe place.

Safety Instruction

• Before using it, check whether the power cord is well connected or not; if not, please don’t use it, and call the service center;
• Before using it, check whether the plug conforms with the socket or not; if not, please don’t use it, and call the service center;
• Do not connect or disconnect the electric plug when your hands are wet.
• Place the Beer dispenser on a dry and horizontal surface.
• To ensure proper ventilation for the Beer dispenser, make sure the Beer dispenser is at least 5 inches / 10cm away on either side so as to allow correct ventilation on the appliance.
• Never put the Beer dispenser under the sunlight.
• Never cover the Beer dispenser when it is operating by some other object.
• The Beer dispenser must be installed in an area protected from the elements, such as wind, rain, water spray, or drips.
• Before proceeding with cleaning and maintenance operation, make sure the power line of the unit is disconnected. Failure to do so can result in electric shock or death.
• Do not immerse the Beer dispenser or power plug in the water or other liquid.
• Do not use coarse cloth, or abrasive stuff to clear the beer dispenser.
• Do not take the beer keg out from the Beer dispenser if the beer is not drunk out completely.
• Never allow children to operate, play with or crawl inside the Beer dispenser.
• This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
• Children should be supervised to ensure that they do not play with the appliance.
• Warning: Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.
• Opening the door for long periods may cause the temperature of the appliance to increase significantly.
• Regularly clean surfaces that come into contact with food and drainage systems.

Suitable for food contact.

Read the instruction manual before using this device. Keep these instructions for future reference. This product complies with the essential requirements of Directives
2014/35 / EU. (Repealing Directive 73/23 / EEC as amended by 93/68 / EEC) and 2014/30 / EU (repealing Directive 89/336 / EEC).

HOW TO SELECT A KEG

• Applicable for sealed 5L keg
• Pay attention to the safety and storage instructions from the pressurized beer keg
• Check the pressurized beer keg is not damaged or expired before purchasing
• Keep the pressurized beer keg in a ventilated area. Do not put the beer keg in too cold places such as refrigerator until next use
• Never shake the pressurized beer keg before using
• Never put the pressurized beer keg under sunlight

SPECIFICATIONS

the keg: 3-6°C
(room temperature
22-24°C)
5| Noise level| 538dB(A); (ambient noise
≤525dB(A))
6| Dimensions| (W)272(D)414(H)446 mm
7| Net weight| 5.8±0.5kg
8| Elegant plastic appearance| √
9| Aluminum radiator system| √
10| Semiconductor cooling technology| √
11| Water conduction cooling system| √
12| Manual drainage outfit| √
13| The detachable water drip tray| √
14| Cool preservation system| PU insulation / Weight 300±5g
15| Climate type| N/SN
16| LCD display| √

PARTS & FEATURE

1. Top cover
2. Tap handle
3. Tap
4. Drain switch
5. Drip tray
6. Rear cover| 7. Power cord & plug
8. AC power switch
9. Door lock button
10. LCD display
11. Digital control button
---|---

INSTALLATION & OPERATION

A. INSTALLATION

1. Take out the Beer dispenser from the package. Put the Beer dispenser on a horizontal surface and ensure that the Beer dispenser is at least 10cm away from other appliances or walls on each side to allow ventilation.
   

2. Install the tap handle on the tap and ensure both end fit together perfectly. (Figure3)

3. Install the drip tray into the notch provided. (Figure 4)

4. Plug the Beer dispenser.
   Note: Do not plug when your hands are wet. Make sure the voltage is conformed with the Beer dispenser. If the power cord is not well connected, do not use it and call the service center.

5. The Beer dispenser can work without water. To achieve the best performance, put 800mL of water or to the max line into the cooling cavity (Figure 5).
   Note: Make sure the drain switch is closed, and no foreign objects are in the cooling cavity. (Figure 6)

B. Pressurized Keg

1. Remove the adaptor from the pressurized keg. (Figure 7) Recycle the adaptor according to the local environmental law.
2. Install the new adaptor on the Beer dispenser and make sure that the hose is well connected. (Figures 8 and 9)

Note: Press the adaptor in both ways as the arrow indicated. Otherwise, the adaptor will be damaged

C. How to use

1. Open the top cover by pressing the door lock (Figure 11). Place the well-assembled keg into the cooling cavity (Figure 10).
   Note: Ensure that the tap is in the closed position when connecting the hose and the adaptor. (Figure 12)
   

2. Close the top cover of the Beer dispenser.

3. Turn on the Beer dispenser by putting the switch into “I” position.
   (Power off at “0” position) (Figure 13)
   Note: Make sure your hands are dry when you use the Beer dispenser.
   

4. It takes 19-21 hours to cool the beet to 3-6°C at a surrounding temperature of 22-24°C. You can shorten the cooling time by pre-cooling the keg in advance.

5. Temperature can be pre-set by pressing the buttons (+ and – next to the temperature display) on the front panel. The temperature can be set from 2°C to 12°C (36°F to 54°F).
   There are 6 pre-set temperatures. The LED shows the real temperature of the beer. The temperature can be set by pressing the “+” button for 1 second. It will show the set temperature for 3 seconds and re-show the actual temperature of the beet.
   By pressing and holding the “-“ button, you can choose a certain preset temperature: 4°C (40°F), 8°C (46°F), 9°C (48°F), 10°C (50°F), 11°C (52°F), and 12°C (54°F) by press the “-“ button. Pressing and holding the “+” button can change the temperature unit between °C and °F.
   The Beer dispenser has a memory function. It will keep the same temperature set as last time when you turn on the Beer dispenser.

6. Pull the tap handle to 45 degrees to pour the beer from the Beer dispenser. (Figure 12) the beer flow rate and bubble can be controlled by adjusting the pressure regulator knob.
   Note: If the glass is at a high temperature or the beer is not cool enough, there might be many bubbles when pouring the beer out.

7. Leaning the beer glass against the tap and slowly straightening it up when pouring the beer from the Beer dispenser. Open the tap completely to avoid too many bubbles. It is suggested to pour half of the glass and pause before continuing to pour the rest.
   Notes: Never immerse the tap into the beer to avoid excessive bubbles. Remember to lock the tap after finishing pouring.

8. Before the beer keg is used up, there will be a short spray from the nozzle.

D. REPLACE WATER INSIDE THE COOLING CAVITY
It is recommended to replace the water inside the cavity once each week. It is not necessary to replace the water for each beer keg.

1. Open the drain switch to release the water from the cavity into the drip tray. Ensure the drip tray fit into the notch to avoid water overflow. The drip tray can load 450mL of water.
2. After all the water drains out, close the drain switch and put 800mL fresh water into the cavity.

CLEANING BEER TAP MECHANISM
Please clean before the first use or after no use in a long time. Clean the whole Beer dispenser with a dry cloth:

1. Use warm water with a cleaning kit.
2. Connect the end of the piercing pin. Push the water into the pin to clean the tube. Push the water out from the tube at the other end. Repeat this process with warm water at least 3 times.
3. Disassemble the tap to clean.

Warning:
Never put the tap mechanism parts in the washing machine or dishwasher; Never use any detergent to clean

TO CHANGE SPARE PARTS

ACCESSORIES INCLUDED WITH YOUR BEER DISPENSER

A. replace the beer tube
Please replace the beer tube if the beer tube is damaged and causes beer leakage. (show as figure 17)

1. Remove the connection 1. Pull the beer handle in the direction of beer pouring when drawing out the beer tube.
2. Take out connection 2 and remove connection 3.
3. Replace a new beer tube, and install the beer tube according to the reverse procedure.

Note: Don’t move other screws when processing tube replacement, otherwise, it may cause beer leakage or gas leakage

MAINTENANCE

If the Beer dispenser does not work properly, please call the service
Troubleshooting

| |
---|---|---
| |
Trouble| Cause| Troubleshooting
---|---|---
The tap does not work / can’t pour beer out| 1. The pouring tube is in poor connection
2. No keg or no beer in the keg;| 1. Well connect the pouring tube.
2. Change a new keg
Too much bubble pouring out| 1. Use the wrong way to pour beer out
2. The beer temp is high (best at 3-6°C)
3. The keg is shaken before usage
4. Almost no beer in the keg| 1. Use the right way to pour beer out
2. Cool the beer down to 3-6°C
3. Put the beer keg aside a while till no bubble inside
4. Change a new keg
Beer flows out too slowly| 1. The connection tube or pouring tube has leakage| 1. Check whether the tube is leakage or not, if so replace the tube

If this logo appears on the appliance, it signifies that it should be scrapped in line with directive 2012/19/UE relating to Waste Electronic and Electric Equipment (WEEE). All dangerous substances contained in electric and electronic equipment may exert deleterious effects on the environment and human health during processing. This explains why at the end of its useful life this appliance should not be disposed of with unsorted municipal waste. As an end consumer, your role is essential in ensuring reuse, recycling, or another form of value creation for this appliance. You have at your disposal several collections and recovery systems put in place by your local authority (recycling center) and distributors. You have the obligation of using these systems.

The warranty does not cover the worn parts of the product, nor the problems or
damage resulting from:

1. surface deterioration due to normal wear and tear of the product;
2. defects or deterioration due to contact with liquids and corrosion caused by rust or the presence of insects;
3. any incident, abuse, misuse, alteration, disassembly or unauthorized repair
4. improper maintenance, improper use concerning the product or connection to an incorrect voltage;
5. any use of accessories not supplied or not approved by the manufacturer.

The guarantee will be canceled if the nameplate and/or serial number of the product are removed.

This product is imported by: SCHNEIDER CONSUMER GROUP
12, rue Jules Ferry, 93110 Rosny-sous-Bois, FRANCE

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>