METRA 99-5807 Double DIN Installation DASH Kit User Guide

METRA 99-5807 Double DIN Installation DASH Kit

KIT FEATURES

• DIN radio provision with pocket
• ISO DIN radio provision with pocket
• ISO DDIN radio provision

KIT COMPONENTS

• A) Radio housing (a)
• B) Radio housing (b)
• C) ISO DDIN brackets
• D) ISO brackets
• E) ISO trim plate

WIRING & ANTENNA CONNECTIONS (sold separately)

Wiring Harness:

• Please visit metraonline.com for more information

Antenna Adapter:

• 40-CR10

TOOLS REQUIRED

• Cutting tool
• Phillips screwdriver
• Socket set

CAUTION! Metra recommends disconnecting the negative bat-tery terminal before beginning any installation, unless the vehicle manufacturer recommends against so. Please check with your local Dealership for more information. All accessories, switches, climate controls panels, and especially air bag indicator lights must be con-nected before reconnecting the battery or cycling the ignition. Also, do not remove the factory radio with the key in the on position, or the vehicle running. It would be best to remove the key from the ignition and then wait a few seconds before removing the factory radio.

Applications

FORD
Edge 2007-2008
Expedition 2007-2008
Explorer 2006-2010
Explorer Sport Trac 2006-2010
F-150 2004-2006
Five-Hundred 2005-2007
Freestyle 2005-2007
Mustang 2005-2009
Taurus/Taurus X 2008-2009

LINCOLN
Mark LT 2006-2008
MERCURY
Montego 2005-2007
Mountaineer 2006-2010
Sable 2008-2009

Dash Disassembly

Ford Explorer 2006-2010, Explorer Sport Trac 2006-2010/
Mercury Mountaineer 2006-2010

1. Open the center console and remove (2) Phillips head screws, and then unclip and remove the entire panel surrounding the shifter. (Figure A)
2. Remove the dash panel surrounding the radio to access the factory radio screws. (Figure B)
3. Remove (4) 9/32” screws securing the radio to the dash and then remove. (Figure C)
   Continue to kit assembly

Ford Edge 2007-2008, Expedition 2007-2008, F-150 2004-2006/ Lincoln Mark LT 2006-2008

1. Unsnap and remove the entire panel surrounding the radio and climate controls. (Figure A)
2. Remove (4) 9/32” Phillips screws securing the radio to the dash and then remove. (Figure B)
   Continue to kit assembly

Ford Five Hundred 2005-2007, Taurus 2008-2009/ Mercury Montego 2005-2007, Sable 2008-2009

1. Unclip and remove the small rectangular trim around the shift lever. (Figure A)

2. Unclip and remove the entire panel (including cup holders) surrounding the shift lever. (Figure B)

3. Remove (2) 9/32” screws at the bottom center of the radio/ climate-control panel. (Figure C)Unclip and remove the panel.

4. Unclip and remove the panel.
   (Figure D)

5. Remove (4) 9/32” screws securing the radio to the dash and then remove. (Figure E)
   Continue to kit assembly

Ford Freestyle 2005-2007,Ford Taurus X 2008-2009
Note: Refer also to the instructions included with the aftermarket radio.

1. Unsnap and remove the entire panel surrounding the radio and climate controls. (Figure A)
2. Remove (4) 9/32” screws securing the radio to dash and then remove. (Figure B)
   Continue to kit assembly

Ford Mustang 2005-2009

1. If equipped, remove the small rectangular trim surrounding the shifter. (Figure A)

2. Remove (2) Phillips head screws from under the center of the armrest at the back of the shifter trim panel (including cup holders), and then unclip and remove the panel. (Figure B)

3. Unclip and remove the (2) center stack trim panels from the left and right side of the radio and climate controls. (Figure C)

4. Remove (6) 9/32” screws from the center trim panel surrounding the radio and climate controls, then unclip and remove the panel.
   (Figure D)

5. Remove (4) screws securing the radio, and then remove. (Figure E)
   Continue to kit assembly

Kit Assembly

DIN radio provision with pocket

1. Remove the metal DIN sleeve from the aftermarket radio.
2. Slide the sleeve into radio housing (a) and secure by bending the metal locking tabs down. (Figure A)
3. Slide the radio back into the sleeve until it clicks in. (Figure B)
4. Locate the factory wiring harness and antenna connector in the dash and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the radio for proper operation.
5.  Reassemble the dash in reverse order of disassembly.

ISO DIN radio provision with pocket

1. Remove the metal DIN sleeve and trim ring from the aftermarket radio.
2. Secure the ISO Brackets to the radio using the screws supplied with the radio. (Figure A)
3. Slide the radio into radio housing (a) until it snaps into place. (Figure B)
4. Snap the ISO trim plate into radio housing (a).
5. Locate the factory wiring harness and antenna connector in the dash and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the radio for proper operation.
6. Reassemble the dash in reverse order of disassembly.

ISO DDIN radio provision

1. Using a utility knife, carefully cut out the center divider from radio housing (a).
2. Slide the ISO double DIN brackets over the mounting legs of radio housing (a), aligning the holes together. (Figure B)
3. From the back, slide the radio between the completed assembly, and then secure the radio using the screws supplied with the radio. (Figure C)
   Note: The notch in the housing should be on top.

IMPORTANT
If you are having difficulties with the installation of this product, please call our
Tech Support line at 1-800-253-TECH.
Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling.

KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry.
Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.

Metra recommends MECP certified technicians

METRA. The World’s best kits.™ metraonline.com © COPYRIGHT 2004-2015 METRA ELECTRONICS CORPORATION

References

• Installer Institute Announces Closure after 31 Years | installerinstitute.edu

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>