CONNECT CSH-10HEX-248 Smart Hexagon Lights User Manual
- June 4, 2024
- CONNECT
Table of Contents
CONNECT CSH-10HEX-248 Smart Hexagon Lights
Specifications:
- Product: AmbiColour Smart Hexagon Lights CSH-10HEX-248
- Indoor Use Only
- Supports 2.4GHz Wi-Fi networks
Product Information
Overview:
The AmbiColour Smart Hexagon Lights provide customizable lighting options for indoor use. The lights can be controlled using the provided controller or through a smartphone app, allowing for various lighting modes and color options.
Installation:
- Peel off the adhesive tape and attach it to the back of a light.
- Connect the controller to the IN port on the light and insert the large connector tip to one of the OUT ports.
- Press the light onto a dust-free and dry surface on the wall for 30 seconds.
- Connect the power adapter and power on the lights using the controller.
Connect with the App:
- Download and install the app on your smartphone.
- Login or register on the app.
- Turn on Bluetooth and Wi-Fi, ensuring a connection to a 2.4GHz Wi-Fi network.
- Follow app instructions to pair the lights with the app.
FAQ
- Q: How do I reset the lights?
- A: To reset the lights, press and hold the POWER button for 10 seconds to enter pairing mode. Follow the app prompts to pair the lights to the app.
- Q: Why are my lights not appearing on the app?
- A: If your lights do not appear on the app, ensure that your Wi-Fi network is set to a 2.4GHz frequency and that you are following the correct pairing procedure as outlined in the manual.
WHAT’S IN THE BOX
- Smart hexagon lights x 10
- Controller
- Connection cables x 9
- Double-sided adhesive sticker x 10
- AC adaptor
- User manual
What you will need:
- Smartphone or tablet with Bluetooth and connected to 2.4GHz band Wi-Fi network
- Password for the Wi-Fi network
OVERVIEW
INSTALLATION
INDOOR USE ONLY
-
Peel off one side of the adhesive tape and stick it to the back of a light.
-
Connect the controller to the IN port (with the arrow pointing into it) on the back of the light. Run the cable through a cable management clip along the edge of the light
-
Insert the large connector tip of a connection cable to one of the OUT ports (with the arrow pointing out of it). Run the cable through a cable management clip.
-
Peel off the other side of the adhesive tape and gently press the light on the wall for 30 seconds.
⚠ Ensure the wall or other surface is free of dust and water before installing -
Stick an adhesive tape to the back of the next light.
- Attach a connection cable to the OUT port.
- Attach the connection cable from the previous light to the IN port.
- Peel off the other side of the adhesive tape and press the light on the wall for 30 seconds.
-
Repeat step 5 for other lights and complete your design.
-
Connect the power adaptor to the controller.
-
Connect the power adapter to a power source and press the Power button on the controller to turn on the lights.
CONNECT WITH THE APP
- Get the app.
- Register or log in to app.
- Recommended app settings
- Turn on Bluetooth and Wi-Fi on your smartphone. Make sure you are connected to a 2.4GHz Wi-Fi access point.
- Connecting lights to app
- Controlling lights with the app.
- Removing light from app.
TROUBLESHOOTING
THE SMART HEXAGON LIGHTS DO NOT APPEAR ON THE APP
- If lights are not blinking rapidly, hold down the power button until they flash once. Then wait for 2 seconds until they start flashing rapidly to enter the pairing mode.
- Enable Bluetooth and Wi-Fi are enabled on your smartphone.
- Ensure that the Wi-Fi signal is strong where it is being installed.
- Make sure you are connected to a 2.4GHz Wi-Fi network. Most modems/routers support both 2.4GHz and 5GHz bands and may use the same Wi-Fi network name (SSID) for both bands. Log into the router’s settings and check:
- Is 2.4GHz band enabled?
- If both 2.4GHz and 5GHz bands are using the same SSID, find the settings that allow you to separate the 2.4GHz and 5GHz bands. Usually, there will be an option to configure each band individually. Change the SSID for one or both bands to make them distinct. For instance, “NetworkName_2.4GHz” and “NetworkName_5GHz”.
- If you are using Telstra Smart Modem, refer to the following guide to resolve band steering issues: https://www.laserco.com.au/Telstra-NBN-Gen-Smart-Modem-Fix
WARNINGS AND CAUTIONS
- For indoor use only.
- This light panel is best used on smooth, dry surfaces and should not be applied to uneven or wet surfaces.
- Ensure the surface is completely dry before applying the light panel.
- Gently press the central point of the light panel against the wall for 30 seconds to maximise adhesion.
- Avoid installing the lights above heat sources in areas where direct sunlight, air flow, and temperature changes significantly.
- To prevent tripping, do not leave the power cord on the floor.
- This product is not a children’s toy. Adult supervision is recommended.
SPECIFICATIONS
Visit our website
Check us out at
Documents / Resources
|
CONNECT CSH-10HEX-248 Smart Hexagon
Lights
[pdf] User Manual
CSH-10HEX-248, CSH-10HEX-248 Smart Hexagon Lights, Smart Hexagon Lights,
Hexagon Lights, Lights
---|---