HALOBEAM200 200W Power RGB 3in1 LED Moving Head User Manual

June 4, 2024
HALOBEAM

HALOBEAM200 200W Power RGB 3in1 LED Moving Head

HALOBEAM200

200W RGB 3in1 LED Moving Head

User Manual

1 SAFETY INSTRUCTIONS

This device has left the factory in perfect condition. In order to maintain this condition and to ensure a safe operation, it is absolutely necessary for the user to follow the  safety instructions and warning notes written in this user manual.

If the device has been exposed to temperature changes due to environmental changes,  do not switch it on immediately. The arising condensation could damage the device.  Leave the device switched off until it has reached room temperature.  This device falls under protection-class I. Therefore it is essential that the device be  earthed.

The electric connection must carry out by qualified person.

The device shall only be used with rate voltage and frequency.

Make sure that the available voltage is not higher than stated at the end of this manual.  Make sure the power cord is never crimped or damaged by sharp edges. If this would  be the case, replacement of the cable must be done by an authorized dealer.  Always disconnect from the mains, when the device is not in use or before cleaning it.  Only handle the power cord by the plug. Never pull out the plug by tugging the power  cord.

During initial start-up some smoke or smell or smell may arise. This is a normal process  and does not necessary mean that the device is defective, it should decrease gradually.  Please don’t project the beam onto combustible substances.

Fixtures cannot be installed on combustible substances, keep more than 50cm distance  with wall for smooth air flow, so there should be no shelter for fans and ventilation for  heat radiation.

If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively  replaced by the manufacturer of his service agent or a similar qualified person in order  to avoid a hazard.

2 UNPACKING

Thank you for choosing our LED 200W moving head light. For your own safety, please  read this manual before installing the device. This manual covers the important  information on installation and applications. Please install and operate the fixture with  following instructions. Meanwhile, please keep this manual well for future needs.

The LED 200W is made of a new type of high temperature strength of engineering plastic and cast aluminum casing with nice outlook. The fixture is designed and  manufactured strictly following CE standards, complying with international standard  DMX512 protocol. It’s available independently controlled and linkable with each other  for operation. And it is applicable for large-scale live performances, theater, studio,  nightclubs and discos.

The 200W Moving head light which features high brightness and stability. Please  carefully unpack it when you receive the fixture and check whether it is damaged during  the transportation. And please check whether the following items are included inside  the box:

  3

3 FEATURES & SPECIFICATIONS  Features

  • 200W High Output White LED 
  • 50,000 hours lifespan and low power consumption
  • Beam Angle: 3°
  • Output: 18690LUX@5M
  • Temperature protect function, when the internal Temperature is up to 40° then the  fans begin to work, when the internal temperature is up to 70°and the brightness  reduce half.
  • Color Wheel: 7 colors +white, color fine tuning, rotation with variable direction and  speed
  • 1 static Gobo Wheel: 8 gobos +white, wheel rotation and shake
  • 1 Rotation Gobo Wheel: 6 gobos +white, wheel rotation and shake
  • Prism: 3-facet Prism, bi-directional rotatable at variable speeds
  • High speed strobe effect with 1-25 flashers per second
  • Internal program available
  • 19/17 DMX Channels USITT DMX-512
  • DMX 512, master-slave and sound activated controllable or auto operation
  • Colorful LCD display
  • Efficient low noise fan cooling system
  • PowerCon IN/OUT
  • 3-pin & 5-pin XLR connectors IN/OUT
  • Two 1/4 turn fastening Omega Clamps
  • IP 20 protection rating

Specifications

Input Voltage: AC90-260V 50/60Hz
Light Source: 200W White LED + 24pcs 0.5W RGB 3-in-1
Control Signal: DMX 512, master-slave and sound activated or auto operation
Control Channel: 19/17 DMX Channels USITT DMX-512
Power Consumption: 315W
Dimensions: 328(L)220(W)482(H)mm
Packing size: 365(L)290(W)600(H)mm
Net Weight: 12.25kg,Gross Weight: 14.85kg

4 PHOTOMETRIC DATA

 5

5 OPERATION INSTRUCTIONS

  • The moving head is for spot effect for on-site decoration purpose.
  • Don’t turn on the fixture if it’s been through severe temperature difference like after  transportation because it might damage the light due to the environment changes.  So make sure to operate the fixture until it is in normal temperature.
  • This light should be keep away from strong shaking during any transportation or  movement. 
  • Don’t pull up the light by only the head, or it might cause damages to the  mechanical parts.
  • Don’t expose the fixture in overheat, moisture or environment with too much dust  when installing it. And don’t lay any power cables on the floor. Or it might cause  electronics shock to the people.
  • Make sure the installation place is in good safety condition before installing the  fixture.
  • Make sure to put the safety chain and check whether the screws are screwed  properly when installing the fixture.
  • Make sure the lens are in good condition. It’s recommended to replace the units if  there are any damages or severe scratch.
  • Make sure the fixture is operated by qualified personnel who know the fixture  before using.
  • Keep the original packages if any second shipments is needed.
  • Don’t try to change the fixtures without any instruction by the manufacturer or the  appointed repairing agencies.
  • It is not in warranty range if there are any malfunctions from not following the user  manual to operate or any illegal operation, like shock short circuit, electronic shock,  lamp broke, etc.

6 INSTALLATIONS

Cautions: For added protection mount the fixtures in areas outside walking paths,  seating areas, or in areas were the fixture might be reached by unauthorized personnel.

Before mounting the fixture to any surface, make sure that the installation area can hold  a minimum point load of 10 items the device’s weight.

Fixture installation must always be secured with a secondary safety attachment, such  as an appropriate safety cable.

Never stand directly below the device when mounting, removing, or servicing the  fixture.

From a ceiling, or set on a flat level surface (see illustration below). Be sure this fixture  is kept at least 0.5m (1.5ft) away from any flammable materials (decoration etc.).

Always use and install the supplied safety cable as a safety measure to prevent  accidental damage and/or injury in the event the clamp fails.

Mounting points: Overhead mounting requires extensive experience, including amongst others calculating working load limits, a fine knowledge of the installation  material being used, and periodic safety inspection of all installation material and the  fixture. If you lack these qualifications, do not attempt the installation yourself. Improper  installation can result in bodily injury.

Be sure to complete all rigging and installation procedures before connecting the main  power cord to the appropriate wall outlet.

Clamp Mounting: The LED moving head provides a unique mounting bracket assembly that integrates the bottom of the base, and the safety cable rigging point in  one unit (see the illustration below). When mounting this fixture to truss be sure to  secure an appropriately rated clamp to the included omega bracket using a M10 screw  fitted through the center hole of the “omega bracket”. As an added safety measure be sure to attached at least one properly rated safety cable to the fixture using on of the  safety cable rigging point integrated in the base assembly.

Regardless of the rigging option you choose for your LED moving head, always be sure  to secure your fixture with a safety cable. The fixture providers a built-in rigging point for  a safety cable on the hanging bracket as illustrated above. Be sure to only use the  designated rigging point for the safety cable and never secure a safety cable to a  carrying handle.

7 DMX-512 CONTROL CONNECTIONS

Connect the provided XLR cable to the female 3-pin XLR & 5-pin XLR output of your  controller and the other side to the male 3-pin XLR & 5-pin XLR input of the moving head. You can chain multiple moving head together through serial linking. The cable  needed should be two core, screened cable with XLR input and output connectors.  Please refer to the diagram below.

For installations where the DMX cable has to run a long distance or is in an electrically  noisy enviroment, such as in a discotheque, it is recommended to use a DMX  terminator. This helps in preventing corruption of the digital control signal by electrical  noise. The DMX terminator is simply an XLR plug with a 120 Ω resistor connected  between pins 2 and 3, which is then plugged into the output XLR socket of the last  fixture in the chain. Please see illustrations below.

 .

8 MENU OPERATIONS

MENU

Address Set [Set Address Numbers]

[DMX]

Run Mode [AUTO] Auto 1- Auto 4

[SOUND]

[MANUAL] Manual Test Function and Operation

Pan reverse

Tilt reverse

Display

Screen Reverse

Setup [Advanced Setting] Channel (19/17CH Select)   Sensitivity (01-100) Motor zero

Reset

Factory Set

 Ver V1

System Information DMX Address

 Temperature

9 DMX CHANNELS

19/17 channel mode sheet

7CH 19CH Function
Channel
Value
Discription
CH1 CH1 Pan 0-255 0-540°
CH2 CH2 Pan fine 0-255 Pan Fine
CH3 CH3 Tilt 0-255 0-270°
CH4 CH4 Tilt Fine 0-255 Tilt Fine
CH5 CH5 X, Y speed 0-255 From fast to slow
CH6 CH6 LED Dimmer 0-255 From dark to bright
CH7 CH7 LED Strobe
0-7 Turn on
8-250 Strobe from slow to fast
251-255 Turn on
CH8 CH8
7 color +
White
0-15 White Lighting
16-31 Color 1
32-47 Color 2
48-63 Color 3
64-79 Color 4
80-95 Color 5
96-111 Color 6
112-127 Color 7
128-191 CW from slow to fast
192-255 CCW from slow to fast
CH9 CH9 Color effect
0-10 No function
11-209 Color fine tuning
210-255 Color shake from fast to slow
CH10 CH10
8 Static
Gobos
+White
0-6 Open
7-13 Gobo 1
14-20 Gobo 2
21-27 Gobo 3
28-34 Gobo 4
35-41 Gobo 5
12
42-48 Gobo 6
49-55 Gobo 7
56-63 Gobo 8
64-70 Gobo 8 shake speed from slow to fast
71-77 Gobo 7 shake speed from slow to fast
78-84 Gobo 6 shake speed from slow to fast
85-91 Gobo 5 shake speed from slow to fast
92-98 Gobo 4 shake speed from slow to fast
99-105 Gobo 3 shake speed from slow to fast
106-112 Gobo 2 shake speed from slow to fast
113-119 Gobo 1 shake speed from slow to fast
120-127 Open
128-191 Gobo Rotate CW slow to fast
192-255 Gobo Rotate CCW slow to fast
CH11 CH11 6 rotation
gobos
+White
0-15 open
16-31 Gobo1
32-47 Gobo2
48-63 Gobo3
64-79 Gobo4
80-95 Gobo5
96-127 Gobo6
128-191 Gobo Rotate CW slow to fast
192-255 Gobo Rotate CCW slow to fast
CH12 CH12
Gobo
Rotation
0-15 open
16-95 Gobo Fine 0-180
96-135 Gobo Rotating 0-90
136-155 Gobo Rotating 0-180
156-175 Gobo Rotating 0-360
176-215 Gobo self-rotating CW from slow to fast
216-255 Gobo self-rotating CCW rotating from
13
slow to fast
CH13 CH13 Focus 0-255 Gobo hazy to clear
CH14 CH14 Prism
0-63 Open
64-255 Prism In
CH15 CH15
Prism
Rotation
0-15 Stop
16-135 Rotate CW slow > fast
136-255 Rotate CCW slow > fast
CH16
LED round
effect
0-25 No function
26-30 Red
31-35 Green
36-40 Blue
41-45 Full color
46-50 Gradual change
51-55 Strobe
56-60 Effect 1
61-65 Effect 2
66-70 Effect 3
71-75 Effect 4
76-80 Effect 5
81-85 Effect 6
86-90 Effect 7
91-95 Effect 8
96-100 Effect 9
101-105 Effect 10
106-110 Effect 11
111-115 Effect 12
116-120 Effect 13
121-125 Effect 14
126-130 Effect 15
131-135 Effect 16
14
136-140 Effect 17
141-145 Effect 18
146-150 Effect 19
151-155 Effect 20
156-160 Effect 21
161-165 Effect 22
166-170 Effect 23
171-175 Effect 24
176-180 Effect 25
181-185 Effect 26
186-190 Effect 27
191-195 Effect 28
196-200 Effect 29
201-205 Effect 30
206-210 Effect 31
211-215 Effect 32
216-220 Effect 33
221-225 Effect 34
226-230 Effect 35
231-235 Effect 36
236-240 Effect 37
241-245 Effect 38
246-250 Effect 39
251-255 Effect 40
CH17
LED round
speed
0-128 Speed CCW from fast to slow
129-255 Speed CW from slow to fast
CH16 CH18
self-setting
Program
0-7 No action
8-131 Auto mode
132-255 Sound mode
CH17 CH19 Reset 0-249 No function
15
250-253 Reset
254-255 No function

10 MAINTENANCE AND CLEANING

The following points have to be considered during the inspection:

  1. All screws for installing the devices or parts of the device have to be tightly  connected and must not be corroded.

  2. There must not be any deformations on the housing, color lenses, fixations and  installation spots (ceiling, suspension, trussing).

  3. Mechanically moved parts must not show any traces of wearing and must not rotate  with unbalances.

  4. The electric power supply cables must not show any damage, material fatigue or  sediments.

Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed.

In order to make the lights in good condition and extend the life time, we suggest a regular cleaning to the lights.

  1. Clean the inside and outside lens each week to avoid the weakness of the lights due to  accumulation of dust.

  2. Clean the fan each week.

  3. A detailed electric check by approved electrical engineer each three month, make sure that the  15 circuit contacts are in good condition, prevent the poor contact of circuit from overheating.

We recommend a frequent cleaning of the device. Please use a moist, lint-free cloth. Never use  alcohol solvents.

There are no serviceable parts inside the device. Please refer to the instructions under  “Installation instructions”.

Should you need any spare parts, please order genuine parts from your local dealer.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals