SHURE SBC200 Battery Charger User Manual

: June 4, 2024
: Shure

Table of Contents

SHURE SBC200 Battery Charger
IMPORTANT SAFETY INSTRUCTIONS
Battery Charger
- Features
Included Components
Adding a Charger
Specifications
Certifications
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SHURE SBC200 Battery Charger

IMPORTANT SAFETY INSTRUCTIONS

READ these Instructions.
KEEP these Instructions.
HEED all warnings.
FOLLOW all Instructions.
DO NOT use this apparatus near water.
CLEAN ONLY with dry cloth.
DO NOT block any ventilation openings. Allow sufficient distances for adequate ventila• tion and Install in accordance with the manufacturer’s instructions.
DO NOT install near any heat sources such as open flames, radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not place any open flame sources on the product.
DO NOT defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades wtth one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wider blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replace• ment of the obsolete outlet.
PROTECT the power cord from being walked on or pinched, particularly at plugs, conve• nience receptacles, and the point where they exit from the apparatus.
ONLY USE attachments/accessories specified by the manufacturer.
USE only with a cart, stand, tripod, bracket, or table specified by the manu- facturer, or sold with the apparatus. When a cart is used, use caution when moving the carVapparatus combination to avoid injury from tip-over.
UNPLUG this apparatus during lightning storms or when unused for long periods of time.
REFER all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged In any way, such as power supply cord or plug is damaged, hquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
DO NOT expose the apparatus to dripping and splashing. DO NOT put objects filled with liquids, such as vases, on the apparatus.
The MAINS plug or an appliance coupler shall remain readily operable.
The airborne noise of the Apparatus does not exceed 70cfB (A).
Apparatus with CLASS I construction shall be connected to a MAINS socket outlet with a protective earthing connection.
To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
Do not attempt to modify this product. Doing so could result in personal injury and/or product failure.
Operate this product wtthin Its specified operating temperature range.

Battery Charger

SBC200 Charger
The SBC200 two-bay charger holds two SBC900 batteries, transmitters, or bodypacks. It may be used in any appropriate location with adequate space and ventilation.

Features

Charge up to two SB900 batteries, body packs or transmitters
Connect up to four units using one PS60 Power supply
LED icons for battery status
Works with compatible handheld and bodypack units such as the P9RA, P1 OR, ULXD1, ULXD2, QLXD1, OLXD2, P3RA, AD1, and AD2

Included Components

SBC200 Charger
PS60 Power Supply (not included with SBC200 model variation)
Screws for attaching additional units (8)
Allen Wrench (hex key)

Note:

This equipment is intended to be used in professional audio applications.
EMC conformance is based on the use of supplied and recommended cable types. The use of other cable types may degrade EMC performance.
Use this battery charger only with the Shure charging modules and battery packs for which it is designed. Use with other than the specified modules and battery packs may increase the risk of fire or explosion.
Changes or modifications not expressly approved by Shure Incorporated could void your authority to operate this equipment.

WARNING

Battery packs may explode or release toxic materials. Risk of fire or burns. Do not open, crush, modify, disassemble, heat above 140 ° F (60 ° C), or incinerate.
Follow instructions from the manufacturer
Only use the Shure charger to recharge Shure rechargeable batteries
WARNING: Danger of explosion if battery incorrectly replaced. Replace only with the same or equivalent type.
Never put batteries in your mouth. If swallowed, contact your physician or local poison control center
Do not short circuit; may cause burns or catch fire
Do not charge or use battery packs other than Shure rechargeable batteries
Dispose of battery packs properly. Check with a local vendor for proper disposal of used battery packs.
Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like
WARNING: Danger of explosion if incorrect battery replaced. Operate only with AA batteries.

Power

Connect DC power cable to the input jack on the bottom of the charger. Finger tighten the lock nut for a secure connection.
Route the cable along the desired channel and press it into place to secure it.
Connect the power cable to AC Adapter.

WARNING:

Do not use pliers or any other tools to tighten lock nut. DC power cable must be attached before the charger unit is installed.
Do not plug-in power supply unit until DC connection and charger are in place.
After securing the charger, plug the power cable into a properly grounded outlet.
The SBC200 has no power switch. When plugged in, the charger is ready. The LEDs illuminate after batteries are inserted.

Adding a Charger

To save space and reduce clutter, up to 4 chargers can share 1 power supply.

Unplug charger from the power source.
Insert set screws into the power pass-through connector.
Align units and tighten screws using the supplied alien wrench. Important: Do not overtighten.
Repeat above steps to add additional chargers.
Connect DC power cable to any input jack on the bottom of the charger. Note: One PS60 will supply power to up to four chargers.

Charging
To charge, place batteries into the charging bays with slotted sides down. The LEDs illuminate to indicate battery status.

Ch arqinq St a t us LED

SHURE-SBC200-Battery-Charger-FIG-5

Battery might be too hot or too cold to take a charge.
Note: Store batteries in the charger or in a proper container. To protect terminals from shorting, DO NOT place batteries in a box or pocket with metal objects such as nails, screws, or keys.

Specifications

Charge Current
0.75A
Charge Time
50% = 1 hour; 100% = 3 hours
External Power Supply
PS60
Power Requirements
15 V DC, 3.33 A max.
Dimensions
66 x 99 x 165 mm (2.6 x 3.9 x 6.5 In.), H x W x D Weight 284 g (10 oz.)

Certifications

Meets essential requirements of the following European Directives:

WEEE Directive 2002/96/EC, as amended by 2008/34/EC
RoHS Directive 2011/65/EU
Note: Please follow your regional recycling scheme for batteries and electronic waste

The CE Declaration of Conformity can be obtained from Shure Incorporated or any of its European representatives. For contact information please visit www.shure.com
The CE Declaration of Conformity can be obtained from: www.shure.com/europe/compliance

Authorized European representative: Shure Europe GmbH
Headquarters Europe, Middle East & Africa Department: EMEA Approval
Jakob-Dieffenbacher-Str. 12
75031 Eppingen, Germany
Phone: +49-7262-92 49 0
Fax: +49-7262-92 49 11 4
Email: info@shure.de