HOMCOM 370-256V00 Childrens Pedal Go Kart Instruction Manual

HOMCOM 370-256V00 Childrens Pedal Go Kart

PARTS

Note: All screws, nuts and small plastic parts are pre-installed in the corresponding position, please follow the steps to remove before you install the product.

Assembly tools required:

WARNING:

1. CHOKING HAZARD-Small parts. Not for children under 3 years.
2. 0nly allowed for adults to install, keep children away.
3. To be used under the direct supervision of an adult.
4. Just only allow one child to use.
5. Please use on a flat and clean surface. Never use near steps, sloped driveways, hills roadways, alleys, swimming pool areas, road, on grass or wet surfaces or other bodies of water.
6. Before driving toy car each time, adult should inspect screws of every parts, please tighten the screw cap if any looseness. secure all fasteners before every ride.
7. Always wear shoes and suitable protective equipment. always wear a local standard approved helmet while riding, with the chinstrap securely fastened.
8. Do not ride the product at dusk, at night or at times of limited visibility.
9. Always comply with local laws and regulations.

MAINTENANCE & CARE

• A. Keep all instructions and parts relating to this product for future reference.
• B. Regularly check for damage and that all screws are securely tightened.
• C. Check that the seat is securely fastened.
• D. Lubricate the chain as often as required.
• E. Regularly check tyre pressures.

ASSEMBLY INSTRUCTIONS

1. Attach the Steering connection plate
   Turn the body over and remove the connecting pieces.

2. Place the connector on the steering bracket. Pay attention to the plane and convex surfaces of the connecting pieces in this step, with the plane facing upwards. The convex surface is used to limit the steering Angle of the steering bracket.

3. Secure with M5*12mm & M5 nut the Steering connection plate.

4. Attach the Rear Wheels

5. Slide the drive bracket into the rear axle.

6. attach the drive bracket to the rear axle using M5*25 screws and MS nuts.

7. attach the drive bracket to the rear axle using M5*25 screws and MS nuts.

8. Slide the rear wheel into the rear axle so that it is connected to the drive bracket.

9. Slide a 10 washer onto the rear axle.

10. Tighten the lock M 10 nut to the end of the rear axle using a wrench.

11. Slide the rear wheel into the rear axle.

12. Slide a 10 washer onto the rear axle.

13. Tighten the lock M 10 nut to the end of the rear axle using a wrench.

14. Attach the Front Wheels & Steering Axle

15. Slide a 12 washer onto the front axle.

16. Slide the wheel into the front axle.

17. Slide a 10 washer onto the front axle.

18. Tighten the lock M 10 nut to the end of the front axle using a wrench. Repeat for the other front wheel. Turn the go cart on its side.

19. Put the 10 washer on the Steering Axle.(Don’t remove the washer from the Steering Axle)

20. Insert the Steering Axle through the steering Axle Support, make sure the other hook to the opening hole on the Front Axle.

21. Attach the Steering Wheel & Front CoverRemove M5*32 screw & M5 nut from the Steering Wheel.

22. Insert the Steering Wheel to the end of the Steering Axle, align the holes of the Steering Wheel and Steering Axle,

23. Secure with M532 screw & M5 nut the Steering Wheel. Remove M4 14 screw from the body.

24. Secure with M532 screw & M5 nut the Steering Wheel. Remove M4 14 screw from the body.

25. Align the Front Cover and Body and insert bottom into the body opening slot,

26. Secure with M4*14 screw the Front Cover.

27. Attach the Seat
    Remove M5*55mm & M5 nut from the Body.

28. Align and assemble the Seat to the Body

29. Secure with M5*55mm & M5 nut the Seat.

Use your New bicycle

1. Brake : Pull the brake to slow or stop.
2. Pedals : To move the vehicle forward and reverse.
3. Steering wheel: Controls the direction of the vehicle.

Chain Adjustment

The chain must be at the correct tightness. If too tight, the bicycle will be difficult to pedal. If too loose, the chain can come off the sprockets.

Adjust the tightness of the chain as follows:

• A. Turn the product downside up. Remove the ten screws on the bottom of the product with a screwdriver.
• B. Press the two buckles on the side of the product, Lift up the chain cover.
• C. Loosen the four fixed screws and adjust the screws according to the tightness of the nut.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>