Hunter Douglas Architectural RB-500Plus Roller Shades with Heavy Duty Brackets Outside Mount User Manual
- June 1, 2024
- Hunter Douglas Architectural
Table of Contents
Hunter Douglas Architectural RB-500Plus Roller Shades with Heavy Duty
Brackets Outside Mount
Specifications
- Product Name: RB 500+ Manual Roller Shades
- Mount Type: Outside Mount
- Brackets: Heavy Duty Brackets
- Manufacturer: Hunter Douglas Architectural Window Coverings
Product Usage Instructions
Installation Process
- Ensure you have all the necessary materials listed in the manual.
- Attach the brackets with screws using a 5/16 hex driver, ensuring they are level and aligned.
- Measure and mark the width of the shade inside the window casement.
- Pre-drill screw holes using a 5/32 drill bit.
- If you have the pre-assembled leveler, make sure it is positioned correctly for adjustment.
- Install roller shades after mounting the brackets. Do not remove the tape around the shade until fully installed.
Installation of Components
- Install screw covers over screws and snap into place.
- Mount the cord tensioner as per the instructions provided.
- Attach the clutch end of the shade onto the clutch-side bracket with the clutch pointing down.
- Insert the idle end of the shade into the idle end bracket.
- Secure the shade by turning the locking ring away from the bracket.
- Set bead stops and install bracket covers.
- Check that the shade is level and aligned. Test operation by pulling on both sides of the chain loop.
WARNING
Window Blind Cord Strangulation Risk Window blinds with a damaged or loose
tension device or retractable cord that fails to fully retract pose a
strangulation risk to children. To avoid this potential strangulation risk,
consider purchasing cordless products or products with inaccessible cords.
Materials Needed
Installation Process
- Measure and mark the ordered width of the shade inside the window casement. A minimum 31/2” vertical surface is required to mount the brackets.
- Place your first bracket in its mounting location and mark the screw holes. Place your second bracket and repeat the process.
- Pre-drill your screw holes using a 5/32” drill bit.
- If your shade order did not include a leveler, go ahead and attach the brackets with the provided screws using the 5/16” hex driver.
- The brackets should be level and aligned.
- If you’ve chosen the pre-assembled leveler option, ensure that the opening to access the leveling set screw is pointing downward before installing the brackets. This is where you will insert the provided Allen Key to adjust skewing.
- To adjust, insert the Allen Key into the set screw of the leveler. To lower the shade, turn the Key to the right to rotate the set screw clockwise. To raise the shade, turn the Key to the left to rotate the set screw counter clockwise.
- Once the brackets have been mounted you are ready to install your roller shades. Note that the tape around the shade should not be removed until the shade is fully installed.
- First, let’s install the screw covers. Simply place the covers over the screws and snap into place.
- Next, install the clutch end of the shade onto the tab on the clutch-side bracket. The bottom of the clutch should always point straight down.
- Finally, push the idle end into the shade and place into the idle end bracket.
- Secure the shade by turning the locking ring away from the bracket. At this point, the tape band and child safety tag can safely be removed.
- Now is a good time to check that the shade is level and aligned.
- Now you’re ready to mount your cord tensioner. Please refer to the video below for directions:
- Outside Mount Video
- Once you’ve finished setting your bead stops, go ahead and install the bracket covers by sliding onto the brackets and snapping into place.
- Pull on both sides of the chain loop to ensure the shade is operating in the up and down direction.
Uninstallation Process
- Start by unscrewing the cord tensioner.
- Loosen the locking ring by turning it in the direction of the bracket.
- Next, push the idle end into the shade while pulling the shade towards you. This will allow you to pull the clutch end out of the clutch bracket.
- Finally, snap off the screw and bracket covers using a flat-blade screwdriver, and with your drill, remove the screws and brackets.
Congratulations
You have now successfully installed and uninstalled an outside-mounted RB
500+ Manual Roller Shade with Heavy Duty Brackets.
Window Coverings
- Hunter Douglas Architectural Window Coverings continues to deliver expertly engineered solutions to manage light and glare control.
- This booklet provides installation instructions that can be used as a stand-alone piece or may accompany video instructions at bit.ly/2vm9z2p
Copyright © 2019 Hunter Douglas Architectural
800-727-8953
HDarchitectural.com
FAQ
- Q: Can I install the roller shades without using a power drill?
- A: While a power drill is recommended for installation efficiency, you can use alternative tools like manual screwdrivers, but it may require more effort.
- Q: How do I adjust the roller shades if they are not operating smoothly?
- A: Check for any obstructions or misalignments in the brackets first. If needed, adjust the skewing using the provided Allen Key in the leveler.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>