Autex Acoustics SpinFix Micro QR Wheel Mount Instructions

: June 1, 2024
: Autex Acoustics

Table of Contents

Autex Acoustics SpinFix Micro QR Wheel Mount
Specifications
Product Usage Instructions
FAQs
Overview
Install method
CONTACT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Autex Acoustics SpinFix Micro QR Wheel Mount

Specifications

Product: SpinFixTM
Mounting System: Adhesive-free using clips made from repurposed waste PET
Components: SpinFixTM Panel Clip, SpinFixTM Washer, SpinFixTM Button, Drill Tool, Hang-Right Bracket
Installation: Follow provided instructions and specifications
Air Gap: SpinFix clips create a 6 mm air gap for added acoustic performance

Product Usage Instructions

Prepping the Wall
- Unbox panels and accessories, ensuring all parts are included and suitable for installation.
- Fix Hang-Right brackets to the wall where the panels will be installed.
- Measure and mark the fixing points on the wall.
- Click SpinFix clips to buttons on the panels.
Prepping and Fixing the Panel
- Press the panel onto SpinFix clips to mark the fixing points on the panel.
- Connect SpinFix clips to the panel.
- Fix the panel to the substrate following the marked fixing points.
- Repeat the process for adjacent panels.
- Note: For bottom-edge alignment, consider using a kick trim. Autex Acoustics Edging Solutions accessories can also enhance the installation execution.

FAQs

Q: Can SpinFix clips be reused?
- A: SpinFix clips are designed for single-use installations. Reusing them may compromise the integrity of the mounting system.
Q: Are SpinFix panels suitable for outdoor installation?
- A: SpinFix panels are recommended for indoor use. Outdoor installation may expose them to conditions that could affect performance.

Overview

Product Overview

SpinFix™ is an adhesive-free mounting system that uses clips made from repurposed waste PET to fix the panel in place.
This process doesn’t add any foreign materials to the acoustic panel which makes end-of-life reuse and recycling much easier.

Specification

$Autex-Acoustics-SpinFix-Micro-QR-Wheel-Mount-FIG-1 $1$$

General information

SpinFix accessories should always be installed per the below instructions and as per the specification detail.
If there is conflicting information, you must seek clarification from all appropriate parties before proceeding.
The installation must be planned before cutting and installing any product.

Install method

SpinFix—prepping the wall

Unbox panels and accessories,
and check all parts are included and suitable for installation.
Fix Hang-Right brackets to the wall.
Use a laser level to align Hang-Right Brackets where you intend the bottom edge of your panel(s) to sit once installed.
Use a single screw per Hang-Right Bracket. Do not overtighten as brackets will be removed after installation.
Not required if you have a skirting board to align to.
Measure and mark fixing points.
Ideal clip spacing is 100 mm in from panel edges, and 550 – 625 mm apart.
Approximately 15x fixing points are required per 2400 x 1200 mm panel.
Adjust fixing points for studs as required.
Fix the SpinFix button and washer to the substrate.
It is the building contractor’s responsibility to use appropriate wall fixings.
6 gauge screws are recommended.
Click SpinFix clips to buttons.

SpinFix—prepping and fixing the panel

Press the panel onto SpinFix clips to mark the fixing points.
Position the panel on your Hang-Right Brackets in the exact position the panel will be installed.
Firmly press the panel around each clip position to create an impression in the sheet.
Note: do not hit the panel, as this can discolor the material.
Once all SpinFix clips have been pressed, remove the panel and lay flat on a working surface. At this point, you should see 15 small impressions in the back of the panel. These are your fixing points.
Remove SpinFix clips from buttons on the wall.
SpinFix clips create a 6 mm air gap for added acoustic performance.
Connect SpinFix clips to the panel.
Attach the Drill Tool to the power drill.
Set the spin speed and torque to high.
Locate SpinFix clip point on the panel impression.
Push Drill Tool into SpinFix clip. Use the weight of the drill as pressure when fixing clips.
Hold the power drill straight and pull the trigger. Spin at max speed for approximately 3-5 seconds (until the clip edge is flush with the panel surface).
Stop spinning, hold the clip with your fingers, and remove the Drill Tool from the clip.
Repeat the process for adjacent panels.
Note: a consistent kick trim is ideal for bottom-edge alignment during installation and throughout product life.
Autex Acoustics Edging Solutions accessories can also be utilized for refined install execution.
Fix the panel to the substrate.
Once all clips are attached to the panel, transfer to the fixing wall.
Press SpinFix clips to wall buttons, leaning your panel on the hang-right brackets to align.
An audible click should register that the SpinFix clips are fixed.
Tip: start with the top SpinFix clips, this will help simplify finding and pressing the following clips.
Remove Hang-Right Brackets from the wall to use on the next panel. The two screws that held the Hang-Right Bracket can remain in the wall hidden by the installed panel.

CONTACT

New Zealand
- 702-718 Rosebank Road,
- Private Bag 19988
- Avondale 1746, Auckland
- T 0800 428 839
- T +64 9 828 9179
- www.autexacoustics.co.nz.
Australia
- 285 Swan Street,
- Richmond, VIC 3121
- T 1800 678 160
- T +61 3 9450 6700
- www.autexacoustics.com.au.
United Kingdom
- Unit J4, Lowfields Way,
- Lowfields Business Park,
- Elland, West Yorkshire
- HX5 9DA
- T +44 0 142 241 8899
- www.autexacoustics.co.uk.
United States
- 1630 Dan Kipper Drive,
- Riverside, CA 92507
- T +1 424 203 1813
- www.autexacoustics.com.

Autex is an ISO-certified organization encompassing Quality (ISO 9001), Environmental (ISO 14001), and Health and Safety (ISO 45001). Brand names and logos are registered or unregistered trademarks owned or used under license by Autex Industries Limited or other members of the Autex Group. © Copyright 2023 Autex Industries Ltd. All rights reserved. It is the user’s responsibility to determine if the product and information presented in this document are suitable for the intended application by engaging a suitably qualified consultant. The information contained in this document is correct to the best of our knowledge at the date of its publication. To verify that this document is the most current publication please check our website or contact your Autex account manager.