RuRoc ATLAS 4.0 Full Face Bluetooth Motorcycle Helmets Instruction Manual

RuRoc ATLAS 4.0 Full Face Bluetooth Motorcycle Helmets

Product Information

Specifications:

• Manufacturer: Ruroc
• Warranty: 1 year from the date of purchase
• Usage: Headphones
• Power Source: Battery
• Waterproof: No

Product Usage Instructions

Warnings and Precautions:
Before using the product, please read and adhere to the following warnings and precautions:

1. Only use the product in private spaces, complying with local laws.
2. Avoid using headphones while riding if prohibited by local laws.
3. Maintain volume at an appropriate level to prevent damage to ears.
4. Follow battery precautions to prevent damage, injury, or accidents.

Battery Usage Precautions:
Properly handle and care for the battery to ensure safety:

1. Dispose of batteries according to local regulations.
2. Avoid short-circuiting the battery by preventing contact with metal objects.
3. Avoid extreme heat or fire to prevent overheating, bursting, or combustion.
4. Do not disassemble, puncture, or modify the battery to avoid leaks or fire.
5. Avoid skin contact with battery electrolytes and seek medical attention if exposed.

Warranty Information:
Ruroc offers a one-year warranty against defects in material or workmanship. Notify us promptly in case of any defect within 7 days for a free repair or replacement.

Frequently Asked Questions

Q: Can I use the product on public transportation?

A: It is not recommended to use the product on public transportation due to potential legal restrictions. Please refer to local laws.

Q: What should I do if the battery overheats?

A: If the battery overheats, stop using it immediately and replace it to avoid safety issues. Do not charge it near flammable objects.

Q: Can I dispose of the battery with general household garbage?

A: No, please follow local recycling regulations for proper disposal of batteries to protect the environment.

WARNING!
READ THIS MANUAL BEFORE USE

1. The use of this device on public transportation may not be authorized by law. Please check your local laws and use this product only in private spaces.
2. If local law prohibits the use of headphones while riding, do not use them. If you do not comply with this warning, Ruroc does not accept any liability.
3. Use of this product at a high volume for a long time may cause damage to your ears & hearing. Please keep the volume at an appropriate level.

PRECAUTIONS OF BATTERY USE

1. Please do not put discarded batteries together with general household garbage. In areas with laws and regulations on recycling & disposal of waste batteries, please follow these regulations.
2. Don’t short-circuit the battery. A short circuit occurs when metal objects (keys, jewellery, wires, coins, or other conductors) accidentally connect the positive and negative electrodes of a battery. A short circuit can damage batteries or connectors and may cause significant property damage or personal injury. Please care for the batteries properly and do not leave them in your pocket, wallet or bag with metal objects.
3. Do not set the battery on fire or leave it in a hot place to avoid overheating, bursting or combustion.
4. Do not disassemble, weld or modify the battery. Do not puncture the battery with a hard object as the battery may leak, overheat, burst or catch fire.
5. Do not remove, squeeze, heat or burn the battery inside the product. It is strictly prohibited to use sharp objects, screwdrivers, or other devices to puncture or pry the battery open. The above operation may cause the battery to catch fire or burn.
6. If the battery electrolyte (fluid) enters the eye, it can lead to blindness. If you splash the battery electrolyte (fluid) into your eyes, do not rub your eyes with your hands. Rinse thoroughly with water immediately & seek medical attention. If the battery’s electrolyte (fluid) sticks to the skin and clothes, wash them immediately with soapy water & clean water and seek medical attention if necessary.
7. Do not transfer batteries from other products. Do not use any damaged chargers or batteries. If the temperature of the battery is too high during use, charging or storage, or abnormal phenomena such as discolouration, deformation, bulging & leakage occur in the battery, please stop using & replace the battery to avoid safety problems.
8. The battery is not waterproof; do not use or charge the battery in the kitchen, bathroom or high-temperature or humidity areas.
9. When charging, the temperature of the battery will rise. Therefore, please do not put the battery inside flammable objects (such as bedding, clothes, etc.) to avoid fire. Doing so may cause the battery to overheat or even explode.

WARRANTY INFORMATION

• Ruroc warrants all products to be free of defects in material or workmanship for one year from the date of purchase, subject to the provisions below.
• If a Ruroc product fails due to defects in craftsmanship or materials, within the warranty period, we will repair or replace the product free of charge provided that you promptly notify us of any defect (in any event within 7 days) and you immediately cease to use the product in question. Please be aware that this warranty is limited to the original purchaser only.
• For detailed information please see the guideline below and/or the product specification following the product.

If you have any questions regarding our products or the above warranty, please feel free to contact our service centre here.

1. Before you return any product, please go to www.ruroc.com/returns and follow the online returns process.
2. Ensure that the returned product is clean and dry before shipping. Dirty and/or foul-smelling helmets will be returned unprocessed or may delay the process with an additional surcharge.
3. Remember to include a note with your name, address, and phone number AND, make sure to include a short statement explaining the warranty problem.

Alternatively, you may also return your product to the store from where you originally purchased the product. Any Ruroc dealer can handle the warranty process on your behalf.

NOTE:
Damage due to wear and tear, accident, misuse, or neglect, or if you fail to store or use a product other than by the instructions provided, or damage due to any repairs carried out by you or a third party not authorised by us, is not covered under warranty. Please contact our warranty department if you have any questions.

SAFETY

1. Please keep the products and all spare parts out of the reach of children and pets. Small parts can cause suffocation or other dangerous conditions.
2. Safe startup: be sure to use your product in a safe environment as electronic products may cause distraction or loss of concentration.
3. Pay attention to traffic safety. Please comply with all relevant laws and regulations of the place of use. Never use this product after drinking alcohol or using drugs, or when you are extremely tired.
4. Interference: any interference with a Wireless product can affect its performance. Shut down near medical devices: hospitals & health care facilities may have equipment that is sensitive to radio-frequency. Please effectively follow the rules & regulations of any medical institution & turn off the product when necessary.
5. The use of wireless devices on an aircraft can interfere with the aircraft, so please shut down the electronic device during flights.
6. Do not use this product near a gas station (service station) or where fuel or chemical agents are stored.
7. Accessories and batteries: Please only use accessories and batteries approved by Ruroc. Using other accessories and batteries may damage the product & cause harm.
8. Connecting to other devices: when connecting to other devices, please read the device’s instructions carefully for detailed safety instructions & correct product operation. Do not connect incompatible products.
9. DO NOT charge the Shockwave unit whilst riding a motorcycle, the charging unit can cause injury/serious injury in the event of an accident.

FITTING YOUR SHOCKWAVE

1. Remove the Snap-Fit Bluetooth cover on both sides of the helmet. Keep these covers stored securely should you wish to re-use them in the future.
2. Insert Battery into side [A] by lining up the locators with slots in the battery cavity, and press until it ‘CLICKS’.
3. Insert Shockwave into side [B] by lining up the locators with slots in the Shockwave cavity, and press until it ‘CLICKS’.
4. More information about how to install your Shockwave can be found here.

CONNECTING YOUR SPEAKERS

1. Gently release the poppers on the cheek pads and remove them from the helmet.
2. Plug the Mic+Speaker cable [C] into the AUX jack port on the helmet’s left side (right side of the below diagrams).
3. Plug the Speaker-only cable [D] into the AUX jack port on the helmet’s right side (left side of diagrams)

FITTING YOUR SPEAKERS

1. Attach each of the Shockwave speakers where Velcro [E] is located (in the orientation shown in the diagram)
2. Attach the Shockwave Mic where Velcro [F] is located to the side of the chin vent (in the orientation shown in the diagram)
3. Carefully re-attach the cheek pads over the top of the speakers and Mic cable.

SHOCKWAVE CONTROLS

SHOCKWAVE UNIT

BATTERY

ON/OFF

• ON:
  Press both the Intercom Button and Media Button once to switch on the Shockwave system, you will hear a “Power On” message.

• OFF:
  Press both the Intercom Button and Media Button once to switch off the Shockwave system, you will hear a “Power Off” message.

REBOOT SHOCKWAVE

To Reboot the Shockwave hold the Intercom Button and Media Button for 10+ seconds, a voice message of ‘Power Off’ will sound, and turn back on the system as normal.

FACTORY RESET
To Factory Rest the Shockwave hold the Intercom Button Media Button and Select/Phone Button for 5+ seconds, a voice message of ‘Reset’ will sound, and turn the setback onions as normal.

CHARGING

• Plug the USB-C cable into the charging port, the LED will light up the RED and stay static to indicate it is charging.
• When the device is fully charged, the RED LED will flash to indicate that it is fully charged.

NOTES:

• Never charge the battery whilst it is installed in the helmet.
• Never let the battery completely discharge to 0% (10% Maximum), doing so may degrade the battery life.
• Average Charge Time = 1 hr 38 mins

CONNECTION

BLUETOOTH CONNECTION

1. When connecting the Shockwave system to your device for the first time*, hold the SELECT/PHONE BUTTON** for 5 seconds until you hear ‘phone pairing’
2. The LED will flash RED & BLUE as the Shockwave looks for a connection to the device.
3. From your device, enter the Bluetooth® menu and select “Shockwave BT”.
4. You will hear the message ‘Connected’ to confirm the connection, and the BLUE LED will flash once periodically while the devices remain paired.

NOTES:

• Your Shockwave will automatically connect to a previously connected device (within range) when powered on.
• If the unit is already on, pressing the SELECT/PHONE BUTTON for 5 seconds will put the unit into pairing mode

CARDO CONNECT APP

GENERAL

VOLUME UP

VOLUME DOWN

MUTE/UNMUTE MICROPHONE

VOICE ASSISTANT

PAIRING

PHONE 2 PAIRING

GPS PAIRING

BIKE PAIRING

CYCLE BACK TO PHONE PAIRING

STOP DEVICE PAIRING

RADIO

Set Presets

RADIO ON

RADIO OFF

NEXT PRESET

PREVIOUS PRESET

AUTO-TUNE x6 PRESETS

MUSIC

MUSIC ON

MUSIC OFF/PAUSE

NEXT TRACK

PREVIOUS TRACK

START/STOP MUSIC SHARING

SWITCH SOURCE RADIO/MUSIC

PHONE

ANSWER CALL

IGNORE CALL

END CALL

REDIAL LAST NUMBER

SPEED DIAL

DMC (DYNAMIC MESH COMMUNICATION)

OPEN PUBLIC MODE INTERCOM

CLOSE PUBLIC MODE INTERCOM

START DMC GROUPING

STOP DMC GROUPING

MUTE DMC GROUP

SHARE PHONE CALL WITH GROUP

START/STOP PASSENGER BLUETOOTH TO DMC GROUP

START/STOP PRIVATE CHAT (PREDEFINED PARTNER)

BLUETOOTH INTERCOM

SWITCH SOURCE DMC/BLUETOOTH

START INTERCOM RIDER ‘A’ PAIRING

START INTERCOM RIDER ‘B’ PAIRING

RETURN TO RIDER ‘A’ PAIRING

STOP INTERCOM PAIRING

START/SHOP SHARE PHONE CALL WITH BLUETOOTH INTERCOM CHANNEL (‘A’ OR ‘B’)

BLUETOOTH INTERCOM – OPEN/CLOSE CHANNEL (A&B)

Voice Commands

Voice Commands – Always On!

FCC REGULATORY COMPLIANCE

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

• This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
• Any change or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
• The transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
• This equipment complies with RF radiation exposure limits set forth for an uncontrolled environment.
• This device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC ID: 2AZ5F-SW-BT

COMPLIANCE CE

• This device complies with RF specifications when the device is used in typical operation.
• Hereby Ruroc Ltd declares that this product complies with essential requirements and other relevant provisions of Directive 2014/53/EU.
• This device can be operated in all EU member states.
• For further information, please visit https://support.ruroc.com/.

ATTENTION

1. Installing equipment on the helmet is a modification of the helmet, which may cause the helmet’s warranty to fail or hinder the helmet’s function. This may cause danger in the event of accidents.
2. Before using the Shockwave Bluetooth system, please ensure that the product is firmly and correctly installed in the helmet. If the product falls off during riding, it may cause injury or accident.
3. To ensure riding safety, please use this product carefully to avoid injury, serious harm or death.
4. To maximise the communication distance, aim to use the system in an open space with a clear line of sight.
5. In the case of rain, please keep the USB rubber plug tightly installed during use to prevent water from entering the device.
6. The device contains a 3.8V/650mAh LiPoly (Lithium Polymer) battery that will change with temperature. When the battery is used at a low ambient temperature (0°C), the battery life of the product may be temporarily reduced, with a risk of permanent damage.
7. If the electronic functions fail, please power off the device and try again.

SPECIFICATION

• BLUETOOTH® VERSION: DUAL-MODE BT 5.3 WITH LE AUDIO
• SUPPORT: STAR-MC1 PROCESSOR, BECO COPROCESSOR
• ELECTRIC PARAMETER: DC 5V/1A
• AUDIO ENCODING FORMAT: SBC, (4) AAC (MPEG-2)
• RIDER-PILLION INTERCOM COMMUNICATION DISTANCE: UP TO 100 METERS
• BLUETOOTH® HEADSET COMMUNICATION DISTANCE: UP TO 10 METERS
• CHARGING INTERFACE: USB TYPE-C
• PERMISSIBLE OPERATING TEMPERATURE: -20~+45°C / -4~+113°F
• RECOMMENDED STORAGE TEMPERATURE: -5~+30°C / 23~+86°F
• WATERPROOF RATING: IP64

CARDOSYSTEMS.COM/UPDATE

References

• Product Support Center | Cardo Systems | Cardo Systems
• Cardo Update for Headsets & Speakers | Cardo Systems
• Ruroc | Returns (US)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>