RuRoC M005-MAN-001 Full Face Bluetooth Motorcycle Helmet Instruction Manual

: June 1, 2024
: RuRoc

Table of Contents

RuRoC M005-MAN-001 Full Face Bluetooth Motorcycle Helmet
HELMET CARE / CLEANING / STORAGE
CHIN-CURTAIN
VISOR ADAPTIVE CONTROL
SPEAKER INSTALL
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

RuRoC M005-MAN-001 Full Face Bluetooth Motorcycle Helmet

RuRoC-M005-MAN-001-Full-Face-Bluetooth-Motorcycle-Helmet-product-
image

INSTRUCTION MANUAL
PLEASE DOWNLOAD & SAVE A COPY OF THIS MANUAL FOR YOUR REFERENCE.

WARNING!
READ THIS MANUAL BEFORE USE
If the helmet is worn in the wrong position, it cannot provide you with full protection, in the case of an accident this can result in serious injury or even death.
When wearing the helmet, it should not move freely without moving your scalp along with it. You can check this by holding the helmet firmly and trying to move your head within the helmet. If the helmet moves freely when doing so, the next size down would be required.
WARRANTY PROCESS
Before you return any product, you must go to www.ruroc.com/returns and follow the on-line returns process

Ensure that the returned product is washed, cleaned and dried before shipping. Dirty and/or foul smelling helmets will be returned unprocessed, or may delay the process with an additional surcharge.
Remember to include a note with your name, address and phone number, AND fill out the returns form. Please make sure to include

HELMET CARE / CLEANING / STORAGE

Clean your helmet inside and outside regularly with lukewarm mild soap/ water and a soft cloth. Do not use aggressive detergents, solvents, rough brush/cloth.
WARNING: Do not Paint. Do not use solvents, detergents, thinner, petroleum based products (e.g. gasoline), bleach, ammonia and other cleaning agents as they may damage the materials of the helmet. The damage may not be visible to the user.
Close the buckle and tighten the chin strap so that it feels snug under your chin. Move your head to check that you are still able to breathe, talk and swallow normally. Adjust straps if necessary. Do not wear the strap over the chin, nor use any additional chin cups or similar.
Before using the helmet do a final check by tilting the helmet backwards and forwards. The helmet should remain firmly in place and cannot be taken off in any direction. If the helmet can move freely, rotate or does give a loose fit, the next size down would be required. a short statement explaining the warranty problem. Alternatively, you may also return your product to the store from where you originally purchased the product. Any Ruroc dealer is able to handle the warranty process on your behalf.
NOTE: Damage due to wear and tear, accident, misuse, neglect, failure to store or use a product other than in accordance with the instructions provided, damage due to any repairs carried out by you or a third party not authorised by us is not covered under warranty. Please contact our Customer Experience team if you have any questions.
WARNING: Do not remove or modify any components or parts. Do not make any modifications to the chinstrap or the buckle. Do not make any modifications to the internal shape of the helmet or on its external shell. Do not cut or drill any parts, nor fit any not certified accessory to the helmet.
WARNING: Do not expose the helmet to temperatures over 50°C (around 122°F), such as those it may experience in direct sunlight or in a car. Heat may damage the internal absorption structure. Damages may not be visible to the user. Store the helmet in a dry and dark place when not in use.

PUTTING ON YOUR EOX
Helmets are often tight the first time you put them on and/or take them off. However, the helmet will loosen with use so it is essential you have a firm (but comfortable fit) to begin with. When putting on the helmet be sure to follow these steps to avoid discomfort:

Pull outwards on the fidlock fastening straps to widen helmet.
Place the rear of the helmet against the top part of your neck so the front of the helmet is angled upwards & make sure you continue to pull the helmet wide at the straps.
Roll the helmet forward over your head.
Check your chin strap is tight to your chin & then fasten the Fidlock buckle.

More information is available on how to put on your helmet is available on our ‘how to’ guides.

FITTING YOUR EOX

Helmets will often fit tightly when wearing them for the first time.
With use the internal padding will soften becoming more comfortable for the wearer.
If your helmet fits badly to begin with, we do offer alternative head liner and cheek padding options which are available with different thickness dependent on which you require. You may need to exchange the helmet for a different size if the padding doesn’t help. In order to do so, contact our Customer Experience team and they can initiate the returns process.
Visit our ‘how to’ guides for more information concerning fit.

FIDLOCK BUCKLE

The Fidlock is engaged by moving the top strap (with the metal buckle) towards the bottom fastener strap. Once in position, both parts magnetically lock and engage securely
in the groove. Opening the fastener is just as easy: simply pull the red tab to release. To tighten, pull the strap through the adjustment buckle. To loosen, lift the buckle away from the head, releasing tension on the strap and then adjust to fit.
Visit our ‘how to’ guides for more information

EMERGENCY RELEASE
Emergency release loops are found on the underside of the helmet, pull on the loops to break the popper connection, releasing the cheek padding from the helmet. These tabs are for emergency use only. Excessive use (not in an emergency) may damage the cheekpad assembly. Only use when necessary.
EOX COMFORT LINER

Every EOX comes with a headliner & cheek-pads that are both removable & washable. Not only is this component protective against cold air but it also reduces wind-noise.
To remove your headliner & cheek-pads follow these steps: disconnect the poppers on the cheek-pads and back of the headliner. Then disconnect the plastic band at the front of the headliner. Lastly, gently pull out the liner making sure to help the chin strap through the cheek pads and free the plastic wings on the cheekpads from the internal clips.
To reassemble simply follow these steps in reverse.

LINER WASHING
You may want to wash your Comfortline from time to time to keep it feeling and smelling fresh.

Firstly remove the items you wish to wash from the helmet.
Hand wash the padding in cold water with a mild detergent. Rinse thoroughly and dry out. Exposure to heat / sun may damage / fade the material. Once fully dry, carefully reinsert the liner into the helmet. The emergency tab can be pulled tight at this time (to sit flat) if loose.
Visit our ‘how to’ guides for more information.

CHIN-CURTAIN

Chin curtains (or Wind stops) are essential to keeping unwanted excess air from entering your helmet at high speeds. Not only does this small device prevent you from being hit with high velocity wind but also helps to reduce noise as well as minimizes dust, fumes and bugs.
To install the chin curtain, centralise the unit to be perpendicular to the chin vents, clip in either side using the chin curtain wings and the clips located either side of the EPS between the EPS and shell. Then through a friction fit insert the front of the chin curtain ensuring there is no clash between the wing and the vent body and that the chin curtain is fully under the lower trim.
To remove simply follow the steps above in reverse. $RuRoC-M005-MAN-001-Full-Face-Bluetooth-Motorcycle-Helmet- $5$$
OPEN/CLOSE TOP VENT
- All EOX are equipped with a front open/close vent to give you more control over airflow. Increased airflow (open position) will help to keep your head cooler on warm days.
- Reduced airflow (closed position) will help to keep you warm on cooler days.
RAID AIR-CONTROL
- Thanks to our patented RAID system your helmet’s airflow is second-to-none! At the flick of a switch you are able to transfer air directly to yourself or to the visor. This ‘switch’ is an open/close vent at the inside front of the chin-guard. When the vent is closed the air is transferred to the visor creating clean fog-free vision. When it is opened it offers the rider more air to breathe. $RuRoC-M005-MAN-001-Full-Face-Bluetooth-Motorcycle-Helmet- $7$$
PINLOCK
Our EOX helmets are compatible with both anti-fogging technology and protectint transitional insert. Please note this item will need to be bought separately. Visit our ‘how to’ guides for installation information. Shop PINLOCK
YOUR EOX VISOR
To open the visor, simply place your thumb under the thumb tab and gently pull the visor outwards. Expect some resistance. This is normal. You will hear and feel the visor click through four positions until it is fully open. When in use, please avoid covering the visor and only make adjustments when it is safe to do so.
WARNING: Do not use tinted visors at night.
For day / track use only.
To remove the visor, lift the visor into the fully open position, to reveal the visor release tab. You will know when the visor is in the fully open position when this pin is right at the top. Push and hold down this tab and at the same time, pull the visor forward and away from the helmet to release it. Repeat this action on the other side of the helmet to fully remove the visor. Visit our ‘how to’ guides for installation information.Always ensure your visor is clean before a journey. It is best to use a microfiber cloth with lukewarm water. If your visor is scratched or damaged it should be replaced as soon as possible. Shop EOX Visors

VISOR ADAPTIVE CONTROL

To adapt how tight the visor sits against the seal, simply adjust the two screws on the visor mechanism.
Visit our ‘how to’ guides for more information. $RuRoC-M005-MAN-001-Full-Face-Bluetooth-Motorcycle-Helmet- $9$$

SPEAKER INSTALL

To begin, remove the internal ear pads by gently unfastening the poppers on each side.
Once removed fold the earpads out of the way keeping the sides closest to the lower part of the shell connected. Once the earpads are out of the way you should now be in view of the speaker Velcro on each side of the EPS as well as the microphone Velcro at the front of the helmet.
Place the microphone into position at the front of the helmet in the indicated location marked. Chase the connecting wire back to the speaker and secure to the first Velcro point.
Take the trailing wire and connect to the 3.5mm AUX port. Repeat on the left hand side of the helmet with the single speaker.

BLUETOOTH SYSTEM (ELECTRONICS)
To install your Bluetooth system, remove the plastic covers on both sides of the helmet. On the helmets right side, insert the bluetooth systems battery unit by lining up the locators with the slots in the cavity and then pressing until you hear a click. Repeat this step on the opposite side with the control unit.
Every EOX helmet comes compatible with Shockwave. To install and use your Shockwave correctly please follow the Shockwave manual here.
Visit our ‘how to’ guides for more information.

WWW.RUROC.COM

RUROC EOX CERTIFIED: DOT FMVSS NO 218