dream LIGHTS Gen3 Dream Flagpole Christmas Tree Lights Owner’s Manual
- June 1, 2024
- dream LIGHTS
Table of Contents
dream LIGHTS Gen3 Dream Flagpole Christmas Tree Lights
SERVICE FIRST
Veteran owned & Operated
Service First is owned and operated by Parker Mc Cumber, an OEF Veteran, who
served with the 2nd Cavalry Regiment and 1st Cavalry Division as a Forward
Observer and Fire Support Section Chief.
Parker has also served several years in the Utah National Guard as a Targeting
NCO, and is continuing his service and transitioning to officer ship with the
Utah National Guard. We know the sacrifice service members make, and recognize
their contributions to our great nation as we pay respect to our flag and all
it represents.
“I believe every American should be able to fly our nation’s flag proudly, and
the mission of ServiceFirstProducts.com is to make it easy and affordable for
everyone to have a beautiful flagpole in their yard and at their home.”
- Parker Mc Cumber
PARTS
Conversion Kit
Only available from Service First ™
Suitable for flagpoles 30’ or less
Installation Instructions
Installing your Dream light
A complete installation video is available at www.ServiceFirstFlagpole.com.
These instructions will work for both Telescoping or Sectional Flagpoles. There may be slight differences between actual installation and the graphics/instructions below.
-
Lower or remove your flagpole from the ground sleeve so you can access the top of the flagpole. If you can’t access the top of your flagpole, see Halyard Adapter section. Remove the current finial (gold ball/eagle) and all flags from your flagpole.
-
Using the Star Bolt (D), thread a nut (E) on the upper and lower threads of the Bolt, add a washer and slide through the Light Distributor (A), and screw securely to the top of your flagpole. (see diagram below) *IMPORTANT Hand tighten ONLY!
-
Install the Star Finial (C) onto the Star Bolt (D) and use Nut & Washer (E) to secure. Important Hand tighten ONLY!
-
Connect the Star Finial power cord to the correlated power supply coming from the Light Distributor.
-
f you have a telescoping flagpole extend each section until the flagpole is at the desired height. If you have a Sectional Flagpole, with the help of another adult raise the flagpole and place into the ground sleeve with the Dream lights installed. Flagpole (H)
-
The Large zip-tie (H) can be used to secure the receiver to the flagpole. The receiver hangs from the Light Distributor and can be used to control the lights without the remote control.
The button on the receiver functions like the Mode button on the remote.
-
Untie and pull the strands away from the flagpole. Temporarily stake the strands to the ground using the included tie-down stakes (F). This will keep the strands from getting tangled. Raise or extend your flagpole. Re-adjust the stakes to the desired diameter and location. The included small zip-ties (G) can be used to ensure the light strands stay connected to the stakes if necessary.
You are able to choose the diameter of your Tree Light display. Below are some recommended distances according to flagpole height, however these are just suggestions.-
20’ or less flagpoles
9’ radius
4’ spacing between light strands -
25’ Flagpoles
10’ radius
4.5’ spacing between light strands -
30’ Flagpoles
11’ radius
5’ spacing between light strands
-
**These are approximate distances and may vary depending on sleeve depth and installed pole height.
ARRANGING LIGHTS
The Dream lights are designed to fit flagpoles up to 30’ tall. If they are
installed on a flagpole shorter than 30’, there will be some of the strand
left on the ground. The extra length can be bundled on the ground, arranged as
a base around the pole or cut to a shorter length. More information on cutting
the strand can be found on next page.
Here are a few ways you can arrange the extra strand length with your flagpole
if you choose not to trim your Dream lights.
Examples:
Arranging in a circle
Arranging in X pattern
When staking the light strands to the ground, ensure that the strand has some play in it to account for flagpole sway. Staking the light strands too tight will put unnecessary stress on the light strands and may cause the strand to break as the flagpole moves.
LIGHTS TRIMMING
As explained previously, when the kit arrives the strand length is set to fit
a 30’ Flagpole. You can use the lights at this length with any size flagpole
and arrange the extra length of the strand as you choose. Or if you prefer the
exact strand length for your size flagpole, you can trim the light strand to
length. Please be very cautious when trimming the lights. Once they are cut
they cannot be reconnected.
Before trimming the light strands, make sure you unplug the Dream lights from
power.
Trimming the lights with the power connected can result in electrical shock
and/or damage to the Dream lights.
Measure the lights carefully before cutting. Lights cannot be reconnected
after trimming.
Service First is not responsible for errors made when trimming the lights.
MODE CONTROL
You will need to add 2 AAA batteries to your remote.
On/Of
Timer
Auto Mode
Mode
Patriotic Mode
Patriotic Mode
Pressing the Patriotic Mode button will begin 5 light displays using only Red,
White and Blue colors. The 5 displays will loop after the last is shown.
To set the timer specifically for the Patriotic Mode, press the Patriotic Mode
button and then follow the timer instructions.
Mode
Each time the Mode button is pressed different colors or programs will begin.
The color or program will remain until the Mode button is pressed again.
Auto Mode
Pressing the Auto Mode button will begin a continuous cycle of all colors and
programs in order. The cycle will loop after the last display is shown.
Timer
By pressing the Timer button you can select between two different preset auto
timers:
Once you have selected the color or program you desire, use the below
instructions to set the timer.
- Press Once- LED on controller will flash Red 3 times and the lights will stay lit for 4 hours and then remain off for 20 hours before turning on again.
- Press Twice LED on controller will flash Green 3 times and the lights will stay lit for 6 hours and then remain off for 18 hours before turning on again.
- Press 3x- LED on controller will flash White 3 times and this will CANCEL all timers previously set. You will then need to turn on/off the lights manually.
Note: If the Dream lights lose or are disconnected from power the timer will need to be restarted.
REMOTE CONTROL PAIRING
When your Dream lights arrive your remote should already be paired to the receiver. Occasionally the remote will need to be reconnected (paired) to the receiver again. If your remote is having trouble communicating with the receiver, try to pair the remote again.
- Power off the Dream Lights
- Press and Hold the Receiver button
- Power on Dream lights while continuing to hold down the Receiver button
- The lights will blink blue for 3 seconds
- Release the receiver button
- The lights will blink White
- Press the Mode Button on the new controller
- You are now paired. Test controller function
On/Of
Timer
Auto Mode
Mode
Patriotic Mode
INSTALLATION TIPS
When unboxing the Dream lights for the first time, exercise extreme caution while removing the lights and accessories from the protective shipping wrap. The dream lights have been carefully packed to avoid damage during shipping. Use caution when removing the packaging to avoid damaging the lights.
Installation Tips: Once you have the distributor installed on your
flagpole and you are beginning to unwind the light strands, Use masking tape
to hold the individual strands in place until all the strands are unwound and
you are ready to stake them to the ground. This will keep the strands from
getting tangled as you raise your flagpole.
Storing tips: Be extremely cautious when removing your Dream light system from your flagpole. Wind each strand carefully and use included velcro straps to hold together. Ensure the lights and all parts are completely dried. Package safely in the included storage case and store in dry location.
Replacement Parts: Each light strand is connected separately from the
distributor. If for some reason an individual light or light strand is
malfunctioning it can easily be replaced.
For replacement parts, please contact Service First or visit
www.ServiceFirstFlagpole.com.
Installation Instruction
(optional use) Halyard Adapter
The Dream lights also come with a Halyard Adapter. This adapter is OPTIONAL and can be used if you cannot easily access the top of your halyard equipped flagpole. Instructions: Attached adapter to the Dream lights as shown. Attached the carabiner to your flagpole rope in the same way you would tie a flagpole clip to a halyard. (instructions on how to tie a flagpole clip can be found on our website). Raise the lights using the halyard (rope) to the top of the pole. Secure rope as normal to the flagpole cleat.
Trouble Shooting
Problem:
Light strand(s) is not lit up or colors are not matching the selected program.
Answer:
Detached the affected string from the port. Reattached again and tighten the
connector. Test. If issue persists move to the next step.
Detached affected light string from the port. Attach affected light string to a different port that is working properly. If the light string displays the same problem while connected to a different working port, then the light string is defective and will need to be replaced.
This test is meant to determine if the port or the light string is defective. Once that is determined, contact customer service for a replacement.
Problem:
Light strand(s) is staying illuminated after the power is turned off.
Answer:
Detached the affected string from the port. Reattached again and tighten the
connector. Test. If issue persists move to the next step.
The light strand will need to be replaced. Contact customer service or visit our website for more information.
Customer Support
Designed in the USA Made in P.R.C.
ServiceFirstFlagpole.com
T: 385-985-7244
e: Contact@weareservicefirst.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>