Comet Innovation BC3-109 Distance Monitor Device Instructions
- June 6, 2024
- Comet Innovation
Table of Contents
BC3-109 Distance Monitor Device
Instruction Manual
Layout
L- W-H(45mm X 60mm X 13mm)
Operation
The sample is the Distance monitor function by default, just turn the ON/OFF
button to the ON state, and the function is enabled. The LED will flash once,
a Beep and a vibration reminder when it is turned on.
The alarm distance currently set is 1.5-2.5m. When two or more Bubbles
approach and exceed the alarm distance, the corresponding Pubble will emit a
Beep sound, LED light indication, and vibration.
If the distance gets closer, the beeper, LED light and vibration will increase
urgently.
When reminding, if the battery is low, the vibration reminder function will be
turned off.
When the corresponding Pubble that triggers the alarm returns to a safe
distance, the alarm will be automatically eliminated.
If not used, please turn the ON/OFF button into the OFF state to save power
consumption. When OFF, the LED will flash twice and beep twice.
Low Battery
If low battery, the system cannot be turned on. The LED will light up for 3S
with two Beep reminders, and shut down. In this case, it needs to charge
before turn on.
If the sample detects that the battery is low during the working process, The
LED will flash twice and two Beep reminders. It will be reminded every 10
minutes. In this situation, the sample can continue to be used normally, but
it needs to be charged in time.
If the prototype detects that the battery is very low during the working process and needs to be charged immediately, the LED will be on for 3S and there will be two Beep reminders and shut down. In this case, it needs to charge before turning on.
Recharge
Use DC5V USB power adaptor, please pay attention to the plug direction when
inserting. The wide side of the plug needs to face the button surface.
In order to see the charging instructions, please power ON the sample then
power OFF, During the charging process, different prompts will appear
according to the battery power LED.
After fully charged, the LED will be on after two beep reminders.
Federal Communications Commission (FCC) Statement
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This
the device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired
operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications made to this device not expressly
approved by Xian Chishine Optoelectronics
Technology Co., Ltd may void the FCC authorization to operate this device.
Note: The manufacturer is not responsible for any radio or TV interference
caused by unauthorized modifications to this equipment. Such modifications
could void the user’s authority to operate the equipment.
Radiation Exposure StatementThis equipment complies with FCC radiation
exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with a minimum distance of 20cm between the
radiator and your body.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>