2N IP Intercoms and Access Units Instruction Manual Product Information
- June 1, 2024
- 2N
Table of Contents
- IP Intercoms and Access Units
- Product Information
- Specifications
- Product Usage Instructions
- 1. Express Wizard for Basic Settings
- 2. Firmware Upload
- 3. SIP Server Connection Setting
- 4. Quick Dial Button Settings
- 5. Electric Lock Switching Settings
- Q: How do I update the firmware of my 2N IP intercom?
- Q: Can I use the 2N IP intercom with IP phones without a SIP
IP Intercoms and Access Units
Product Information
Specifications
- Model: 2N IP Intercoms
- Version: 2.42
- Website: www.2n.com
- Processor: Artpec-7
- Camera Resolution:
- 2560 x 1920
- 1920 x 1440
- 1280 x 960
- 640 x 480
- External Analog Camera Support: No
- External IP Camera Support: Yes
- Internal RFID Card Reader: Yes
Product Usage Instructions
1. Express Wizard for Basic Settings
When setting up your 2N IP intercom for the first time, use the
Express Wizard for Basic Settings. Remember to save your new
password securely. If you forget the password, you will need to
reset the intercom to default values, as detailed in the
Installation Manual.
2. Firmware Upload
It is recommended to update your intercom firmware upon initial
login. Visit www.2n.cz for the latest firmware version. Navigate to
the System / Maintenance menu and press the Update Firmware button
to upload the firmware. The updating process will take about 30
seconds and the intercom will restart upon completion.
3. SIP Server Connection Setting
To enable your intercom to make calls within your VoIP
infrastructure, configure the SIP settings in the Services / Phone
/ SIP menu. Set the addresses for your SIP server (Proxy,
Registrar) and enter authentication parameters if required.
4. Quick Dial Button Settings
If you are using the intercom with IP phones without a SIP
server, utilize Direct SIP Call for outgoing calls. Enter the
called phone’s SIP address (sip:phone_number@phone_ip_address)
instead of the phone number.
5. Electric Lock Switching Settings
You can connect an electric lock to the intercom for control via
keypad codes. Follow the instructions in the Installation Manual to
connect the electric lock. Enable the switch in the Hardware /
Switches / Switch 1 tab and set activation codes for the electric
door lock switching.
FAQ
Q: How do I update the firmware of my 2N IP intercom?
A: To update the firmware, visit www.2n.cz to get the latest
version. Then, navigate to System / Maintenance menu on your
intercom, and press the Update Firmware button to upload and
complete the process.
Q: Can I use the 2N IP intercom with IP phones without a SIP
server?
A: Yes, you can use Direct SIP Call feature to make outgoing
calls with IP phones without a SIP server by entering the called
phone’s SIP address.
Configuration manual for 2N IP intercoms
v.2.42
www.2n.com
Configuration manual for 2N IP intercoms
Content:
· 1. Product Overview · 2. Express Wizard for Basic Settings · 3. Model
Differences and Function Licensing
· 3.1 Model Differences · 3.2 Function Licensing · 4. Signalling of
Operational Statuses · 5. Intercom Configuration · 5.1 Status · 5.2 Directory
· 5.2.1 Users · 5.2.1.1 Call Connection Settings · 5.2.1.2 User Fingerprint
Setting Instructions · 5.2.1.3 USB RFID Card Reader
· 5.2.2 Time Profiles · 5.2.3 Holidays · 5.3 Hardware · 5.3.1 Switches · 5.3.2
Audio · 5.3.3 Camera · 5.3.4 Keypad · 5.3.5 Buttons · 5.3.6 Backlight · 5.3.7
Display
· 5.3.7.1 2N® IP Style Display · 5.3.8 Card Reader · 5.3.9 Digital Inputs ·
5.3.10 Extenders · 5.3.11 Lift Control · 5.4 Services · 5.4.1 Phone
· 5.4.1.1 Dial Cycles Limit · 5.4.2 Access Control · 5.4.3 Streaming · 5.4.4
E-Mail · 5.4.5 Automation · 5.4.6 HTTP API · 5.4.7 User Sounds · 5.4.8 Web
Server · 5.4.9 Audio Test · 5.4.10 SNMP · 5.5 System · 5.5.1 Network
2 / 283
Configuration manual for 2N IP intercoms
· 5.5.2 Date and Time · 5.5.3 Features · 5.5.4 License · 5.5.5 Certificates ·
5.5.6 Auto Provisioning · 5.5.7 Diagnostics · 5.5.8 Maintenance · 5.6 Used
Ports · 6. Supplementary Information · 6.1 Troubleshooting · 6.2 Directives,
Laws and Regulations · 6.3 General Instructions and Cautions
3 / 283
Configuration manual for 2N IP intercoms
1. Product Overview
The 2N IP intercoms can smartly replace traditional doorbell push-button
speakerphone panels and all wiring, bells and home intercom installations in
buildings with structured cabling. The intercoms provide more advanced and
wider services than standard home phones. The installation is very easy, all
you need is connect the intercom to the other LAN elements using a UTP cable
and set necessary parameters. Thanks to the integrated SIP protocol, the
intercom can make use of all VoIP services: call forwarding at absence (to
another office, VoiceMail or a cellular phone) or call transfer (from the
secretary’s office to the required person, e.g.). The intercoms are equipped
with a programmable number of quick dial buttons for speed calling to the
users whose numbers are included in the intercom Users list. Each of the quick
dial buttons can be assigned up to three phone numbers, which can be dialled
in parallel or sequentially. Thanks to an integrated time sheet it is possible
to configure each of the buttons in such a way that the called party is always
accessible and/or calls to selected phone numbers can be barred off the
working hours. Some 2N IP intercom models are equipped with a numeric keypad,
which can be used as a code lock or a standard push-button phone. The 2N IP
intercoms help LAN users scan the area in front of the camera via video
streaming. Thanks to the full ONVIF support, the intercoms can become part of
the Video Surveillance System in your facility. The 2N IP intercoms can be
equipped with an RFID card reader for authorised access control and thus
become a key part of your surveillance or attendance control systems. The 2N
IP intercom is equipped with a relay switch (and, optionally, other relays and
outputs), which controls the electric lock or other equipment connected to the
intercom. Its activation time and method can be programmed flexibly: it can be
activated by a code, automatically by a call, by pressing a button, and so on.
It is always recommended that the 2N® Security Relay (Part No. 9159010) is
used for increased security.
4 / 283
Configuration manual for 2N IP intercoms
The following symbols and pictograms are used in the manual: Safety · Always
abide by this information to prevent persons from injury. Warning · Always
abide by this information to prevent damage to the device. Caution · Important
information for system functionality. Tip · Useful information for quick and
efficient functionality. Note · Routines or advice for efficient use of the
device.
5 / 283
Configuration manual for 2N IP intercoms
2. Express Wizard for Basic Settings
LAN Connection Setting You have to know the intercom configuration interface
address to connect to the LAN successfully. Automatic IP address retrieval
from the DHCP server is set by default in the 2N IP intercoms. Thus, if
connected to a network in which a DHCP server configured to assign IP
addresses to all new devices is available, the intercom will obtain an IP
address from the DHCP server. The intercom IP address can be found in the DHCP
server status (according to the MAC address given on the production plate), or
will be communicated to you by the intercom voice function; refer to the
Installation Manual of your intercom model. If there is no DHCP server in your
LAN, use the intercom buttons to set the static IP address mode, refer to the
Installation Manual of your intercom model. Your intercom address will then be
192.168.1.100. Use it for the first login and then change it if necessary. Now
enter the intercom IP address into your favourite browser. We recommend you to
use the latest Chrome, Firefox or Internet Explorer 9+ versions 2N IP intercom
is not fully compatible with earlier browser versions. Use the name admin and
password 2n (i.e. default reset password) for your first login to the
configuration interface. The intercom requires a password change upon the
first login. Strong passwords are only accepted – eight characters at least
including one capital letter, one small letter and one digit.
Remember the new password well or put it down just in case. Because if you
forget the password, you will have to reset the intercom to default values
(refer to the Installation Manual of your intercom model) and lose all your
current configuration changes.
Tip · FAQ : IP address – How to get IP address from 2N IP Intercom?
6 / 283
Firmware Upload
Configuration manual for 2N IP intercoms
We also recommend you to update your intercom firmware upon the first login to
the intercom. Refer to www.2n.cz for the latest firmware version. Press the
Update Firmware button in the System / Maintenance menu to upload firmware.
The intercom will get restarted upon upload and only then the updating process
will be complete. The process takes about 30 seconds.
SIP Server Connection Setting
To allow your intercom make calls and be accessible within your VoIP
infrastructure Set the following parameters in the Services / Phone / SIP menu
to allow your intercom make calls and be accessible within your VoIP
infrastructure.
· Display name set the name to be displayed as CLIP on the called party’s
phone. Set the name to be displayed in the login window and web interface
start page.
· Phone number (ID) set the intercom phone number (or another unique ID
composed of characters and digits). Together with the domain, this number
represents a unique intercom identification in calls and registration. ·
Domain set the domain name of the service with which the intercom is
registered.
Typically, it is equivalent to the SIP Proxy or Registrar address. If you do
not use a SIP Proxy in your intercom installation, enter the intercom IP
address. · Test call display a dialog window allowing you to test a call to
a selected phone number, see below.
If you use a SIP server (Proxy, Registrar), set the addresses for the
following network
elements :
7 / 283
Configuration manual for 2N IP intercoms
· Proxy address set the SIP Proxy IP address or domain name. · Proxy port
set the SIP Proxy port (typically 5060). · Backup Proxy Address set the SIP
Proxy IP address or domain name to be used
where the main proxy fails to respond to requests. The address is used where
the main proxy fails to respond to requests. · Backup Proxy Port set the
backup SIP Proxy port (typically 5060).
· Registration enabled enable intercom registration with the set SIP
Registrar. · Registrar address set the SIP Registrar IP address or domain
name. · Registrar Port set the SIP Registrar port (typically 5060). · Backup
Registrar Address set the backup SIP Registrar IP address or domain
name. to be used where the main registrar fails to respond to requests. ·
Backup Registrar Port set the backup SIP registrar port (typically 5060). ·
Registration Expires set the registration expiry, which affects the network
and SIP
Registrar load by periodically sent registration requests. The SIP Registrar
can alter the value without letting you know. · Registration State display
the current registration state (Unregistered, Registering…, Registered,
Unregistering…). · Failure Reason display the reason for the last
registration attempt failure: the registrar’s last error reply, e.g. 404 Not
Found.
8 / 283
Configuration manual for 2N IP intercoms
If your SIP server requires authentication of terminal equipment, enter the
following parameters:
· Password enter the password for intercom authentication.
Quick Dial Button Settings
All the 2N IP intercom models are equipped with quick dial buttons. If you
press a quick dial button, a call will be set up to the phone number assigned
to the respective Users list position. In the Hardware / Buttons menu is
displayed the list of all potentially available intercom buttons The list is
including those that are physically absent. In some intercom models (2N® IP
Vario, 2N® IP Verso), the button list is divided into 8/ 5-item groups
corresponding to the button extending modules. Click , select the user and
press Add to add a user to the editing field. To search a user in the list,
use the fulltext field and the username. One quick dial button can be shared
by multiple users.
9 / 283
Configuration manual for 2N IP intercoms
You can also use the 2N IP intercom with one or more IP phones without a SIP
server. Use the Direct SIP Call. For outgoing calls and enter the called phone
SIP address (sip:phone_number@phone_ip_address) instead of the phone number.
Electric Lock Switching Settings
An electric lock can be attached to the 2N IP intercoms and controlled by a
code from the intercom numeric keypad, or a code from the IP phone keypad
during a call. Connect the electric lock as instructed in the Installation
Manual of your intercom model.
10 / 283
Configuration manual for 2N IP intercoms
Enable the switch in the Switch Enabled parameter in the Hardware / Switches /
Switch 1 tab, set the Controlled Output to the intercom output to which the
electric door lock is connected. Now set one or more activation codes for the
electric door lock switching.
11 / 283
Configuration manual for 2N IP intercoms
3. Model Differences and Function Licensing
Here is what you can find in this section: · 3.1 Model Differences · 3.2
Function Licensing
included in device licensed function be purchased additionally
unavailable *) The service availability depends on the mobile provider’s
network configuration.
Note · The license overview does not apply to the US, Canada, Mexico,
Caribbean, and Central and South America.
3.1 Model Differences
This manual is valid for all members of the 2N IP intercom family and so some
features described herein are only available in selected 2N IP intercom models
or need to be activated with a valid license key. This section provides a
short list of differences between the models and licenses which affect the
configuration options. If a function is not available in all the models, there
is a note in the respective subsection and reference to this section. The
table below includes an overview of properties and functions of all the 2N IP
intercom models.
12 / 283
Configuration manual for 2N IP intercoms
Property/ Model
2N® IP 2N® IP 2N® IP 2N®
Style Verso Verso IP
2.0
Bas
e
2N® IP Solo
2N® IP Vario
2N® IP Forc e
2N® 2N®
IP
IP
Safet Uni
y
2N® IP Audi o Kit
2N® IP Vide o Kit
Part No.
9157 9155 9155 915 91553 9137 915 915 915 915 915 … 2… … 6… …C …. 1… 2… 3… 4… 4… C
Artpec-7
yes
no
processor
Integrated
yes
opti
yes
optional
no
camera
onal
Camera resolution
2560 1920
x
x
1920 1440
1280 x 960
640 640
x
x
480 480
or
128 0 x 960
External analogue camera support
no
yes
External IP
yes
camera
support
no
yes
Internal
yes
RFID card
reader
Display
yes
optional optional
no
optional
no
opti
onal
no no
13 / 283
Configuration manual for 2N IP intercoms
Property/Model
2N® IP Style
2N® IP Verso
2.0
2N® IP 2N® 2N® 2N® 2N® 2N® 2N 2N® 2N® IP Verso IP IP IP IP IP ® IP IP Video
Bas Sol Vari For Saf Un Aud Kit
e oo
ce ety i io
Kit
Basic unit button count
Button extenders
01
no
up to 145
1 1 1, 3 1, 1
or
or 2
2
6 or
4
no up no to 48
1 up to 16 or external 2 programm
able buttons
Numeric keypad yes
optional
no
optional no
Digital input
yes
optional
no 2
Wideband audio codecs (L16, G.722)
Amplifier power 4 W output
yes 2 W
150 10 W m W
no
yes
10 W
Adjustable microphone gain
Extended
no
amplifier power output (10 W)
no
yes
yes
no no
Tamper switch yes
optional
yes no optional ye no s
Users position count
10 000
2 1 999
14 / 283
Configuration manual for 2N IP intercoms
Property/Model
2N® IP Style
2N® IP Verso
2.0
2N® IP 2N® 2N® 2N® 2N® 2N® 2N 2N® 2N® IP Verso IP IP IP IP IP ® IP IP Video
Bas Sol Vari For Saf Un Aud Kit
e oo
ce ety i io
Kit
User deputy
yes
no yes
Controlled switch count
4
24
14
Switch universal code count
10
2 10
2 10
User profile
20
count
JPEG HTTP
yes
video
no
yes
2N® IP
yes
Eye support
no
yes
Telephone mode
yes
no
yes
no
yes
Some of the 2N IP intercom functions are only available if the valid license key is entered (refer to the License subsection).
3.2 Function Licensing
Feature Licensing
A standard license included in the device is mostly sufficient for a common
use of the 2N IP intercom. In addition, the 2N IP intercom can be extended to
include functions that are subject to a paid license.
15 / 283
Configuration manual for 2N IP intercoms License Types
Some 2N IP intercom functions are unavailable until a valid license key is
entered (refer to the License subsection). The following types of licenses are
available:
· NFC (included in device) · Enhanced Audio (included in device) · Enhanced
Security (included in device) · Gold (Part No. 9137909) · InformaCast (Part
No. 9137910, Axis Part No. 01381-001) Info
· The InformaCast license allows the SingleWire InformaCast protocol to be
used. 2N® IP Style, Verso, Base, Solo, Vario, Force, Safety and Audio Kit with
Video Kit support this license scheme. No licensed features are available for
the 2N® IP Uni.
Tip · Refer to 3. Model Differences and Function Licensing for differences
between the models and function licensing.
The table below includes the functions that need to be activated by the
license keys corresponding to the above mentioned licenses. The licenses can
be combined arbitrarily.
16 / 283
Configuration manual for 2N IP intercoms
Function
User sounds
Enhanc ed
Audio
Enhanc ed
Video
Enhanc ed
Integrat ion
Enhanc ed
Securit y
·
NF Inform C aCast
IP interco ms Lift module license
Licence
included in device
Automatic audio · test
included in device
Noise detection
Audio/video streaming (RTSP Server)
· ·
included in device
GOLD
External IP
·
camera support
GOLD
ONVIF support
·
GOLD
PTZ function
·
support
GOLD
17 / 283
Configuration manual for 2N IP intercoms
Function
Enhanc ed
Audio
Enhanc ed
Video
Enhanc ed
Integrat ion
Enhanc ed
Securit y
NF Inform C aCast
IP interco ms Lift module license
Licence
Motion detection support
Extended switch setting options
· ·
GOLD GOLD
HTTP API (see
·
note below)
included in device
Automation
·
functions
GOLD
E-mail sending
·
(SMTP Client)
GOLD
Automatic update
·
(TFTP/HTTP
Client)
GOLD
FTP client SNMP client TR-069 802.1x support
· · ·
·
GOLD
GOLD
GOLD
included in device
SIPS (TLS) support
·
included
in device
SRTP support Silent Alarm
·
included
in device
·
included
in device
18 / 283
Configuration manual for 2N IP intercoms
Function
Limit unsuccessful access attempts
Enhanc ed
Audio
Enhanc ed
Video
Enhanc ed
Integrat ion
Enhanc ed
Securit y
·
NF Inform C aCast
IP interco ms Lift module license
Licence
included in device
Switch Blocking
Scrambled keypad NFC support
InformaCast support Anti-passback
Genetec Synergis Lift Control IP Relay
·
included
in device
·
included
in device
·
included
in device
·
InformaCa
st
·
included
in device
·
GOLD
·
GOLD
·
GOLD
What other products follow this license scheme?
2N® SIP Audio Converter, 2N® SIP Speaker and 2N® SIP Speaker Horn, which
already come with preloaded Gold license, so the only possible upgrade is
InformaCast.
How do I get the license?
Licenses are generated by 2N according to the particular serial number. After
you decide which license you want, you need to get the serial number of your
unit and contact your distributor for the license key.
The license itself comes as a key, alphanumeric string, so it can be easily
sent via email and copied and pasted into the intercom.
19 / 283
Configuration manual for 2N IP intercoms
Licenses are not limited in time. Once you have a license, you have it for
good. In order to activate the license, you need to log in to the intercom web
interface and paste the license key into the System / License field. When you
click Save, the licensed features are immediately activated. Licenses can be
downloaded automatically in the System / License menu.
Tip FAQ: License for 2N IP intercoms How to get it
Can I have a demo license?
Yes, there is an option for an 800-hour trial Gold license period during which
you can try the licensed features. By default, this demo is disabled enable
it via the web interface of the particular intercom in the System / License
menu. There is a countdown timer showing the remaining time after which all
the licensed features will be disabled again. There is no trial for
InformaCast licenses.
20 / 283
Configuration manual for 2N IP intercoms
4. Signalling of Operational Statuses
2N IP intercom generates sounds to signal switching and changes of operational
statuses. Each status change is assigned a different type of tone. See the
table below for the list of signals.
Tone
Meaning
Call prolongation confirmation signalling Calls are time-limited in 2N IP intercoms for security reasons (protection against blocking). Refer to the Miscellaneous subsection for details.
Internal application launched The internal application is launched upon 2N IP intercom power up or restart. A successful launch is signalled by this tone combination.
Connected to LAN, IP address received 2N IP intercom logs in upon the internal application launch. A successful LAN login is signalled by this tone combination.
Disconnected from LAN, IP address lost This tone signals UTP cable disconnection from 2N IP intercom. Disconnection is signalled by this tone combination.
Invalid telephone number or invalid switch activation code 2N IP intercom allows the user to dial an extension number directly using the keypad or enter the door unlocking code. An invalid code is signalled by this tone sequence.
21 / 283
Configuration manual for 2N IP intercoms
Tone
Meaning
Default reset of network parameters Upon power up, a 30 s timeout is set for the default reset code entering. Refer to the Device Configuration subsection in the 2N IP intercom Installation Manual for details.
Call end signalling 2N IP intercom enables the user to set a call end timeout to avoid call blocking. Press a key on your VoIP phone to extend the call time during this timeout. The purpose of the timeout setting is to avoid call blocking.
Connected VoIP phone This short tone signals successful connection between a VoIP phone and 2N IP intercom.
Note
· Signalling of some of the above mentioned statuses can be modified; refer to
the User Sounds subsection.
22 / 283
5. Intercom Configuration
Configuration manual for 2N IP intercoms
Start Screen
The start screen is an introductory overview screen displayed upon login to
the intercom web interface. Use the back arrow in the left-hand upper corner
of the following web interface pages to return to this screen anytime. The
screen header includes the intercom name (refer to the Display Name parameter
in the Services / Phone / SIP menu). Use the menu in the right-hand upper
corner of the web interface for selecting the language. Click Log out in the
right-hand upper corner of the screen to log out from the device, press the
question mark icon to display Help or use the bubble to provide feedback. The
start screen is also the first menu level and quick navigation (click on a
tile) to selected intercom configuration sections. Some tiles also display the
state of selected services.
23 / 283
Configuration manual for 2N IP intercoms
Configuration Menu
The 2N IP intercom configuration includes 5 main menus: State, Directory,
Hardware, Services and System including submenus; see below.
Status
· Device essentials on the intercom · Services information on active
services and their states · License current states of licenses and available
intercom functions · Access Log last 10 access logs · Call Logs last 20
accomplished calls · Events last 500 events recorded by the device
Directory
· Users settings for user phone numbers, quick dial buttons, access cards
and switch control user codes
· Time Profiles time profile settings · Holidays holiday settings
Services
· Phone telephone and SIP connection settings · Access Control
arrival/departure rule settings · Streaming audio/video streaming settings
(ONVIF, RTSP, Multicast, etc.) · E-Mail E-mail sending and SMTP connection
settings · Automation flexible intercom settings according to the user’s
requirements · HTTP API HTTP API authorisation settings · User Sounds user
sound settings and upload · Web Server web server and access password
settings · Audio Test automatic audio test settings · SNMP SNMP settings
Hardware
· Switches electric lock, lighting, etc. settings · Audio audio,
signalling, etc. volume control, microphone parameters · Camera internal
camera, external IP camera settings · Keypad button and keypad settings
24 / 283
Configuration manual for 2N IP intercoms
· Buttons – user speed dial settings · Backlight backlight intensity setting
· Display basic display settings · Card Reader card reader, Wiegand
interface settings · Digital Inputs digitial input settings · Extenders
2N® IP Verso extender settings · Lift Control floor lift access settings
System
· Network LAN connection settings, 802.1x, packet capturing · Date and Time
real time and time zone settings · Features test function settings ·
License license settings, trial license activation · Certificates
certificate and private key settings · Auto Provisioning automatic firmware
and configuration update settings · Syslog syslog message sending settings ·
Maintenance backup and configuration reset, firmware update · 5.1 Status ·
5.2 Directory · 5.3 Hardware · 5.4 Services · 5.5 System · 5.6 Used Ports
25 / 283
Configuration manual for 2N IP intercoms
Caution
Warning In order to ensure the full functionality and guaranteed performance,
we strongly recommend that the topicality of the product / device version in
use be verified as early as in the installation process. The customer hereby
acknowledges that the product / device can achieve the guaranteed performance
and full functionality pursuant to the manufacturer’s instructions only if the
latest product / device version is used after having been tested for full
interoperability and not having been determined by the manufacturer as
incompatible with certain versions of other products, and only in conformity
with the manufacturer’s instructions, guidelines or recommendations and in
conjunction with suitable products and devices of other suppliers. The latest
versions are available at https://www.2n.com/cs_CZ/ or can be updated via the
configuration interface if the devices are adequately technically equipped.
Should the customer use a product / device version other than the latest one
or a version determined by the manufacturer as incompatible with certain
versions of other products, or should the customer use the product / device in
contradiction to the manufacturer’s instructions, guidelines or
recommendations or in conjunction with unsuitable products / devices of other
suppliers, the customer is aware of and agrees with all functionality
limitations of such a product / device if any as well as with all consequences
incurred as a result thereof. Using a product / device version other than the
latest one or a version determined by the manufacturer as incompatible with
certain versions of other products, or using the product / device in
contradiction to the manufacturer’s instructions, guidelines or
recommendations or in conjunction with unsuitable products / devices of other
suppliers, the customer agrees that the 2N TELEKOMUNIKACE a.s. company shall
not be held liable for any functionality limitation of such a product or any
damage, loss or injury related to this potential functionality limitation.
26 / 283
5.1 Status
Configuration manual for 2N IP intercoms
The Status menu provides clear status and other essential information on the
intercom. The menu is divided into five tabs: Device, Services, License,
Access Log, Call Log and Events.
Device
The Device tab displays basic information on the intercom model, its features,
firmware and bootloader versions and so on.
· Factory Certificate Installed specify the user cerificate and private key
to be used for verifying the intercom authorization to communicate with the
third party device server.
27 / 283
Configuration manual for 2N IP intercoms
· Locate Device optical and acoustic signaling of a device. Optical
signaling is possible only if the device is equipped with control backlight
(2N® IP Style, 2N® IP Verso, 2N® IP Solo, 2N® IP Base, 2N® IP Vario, 2N® IP
Force, 2N® IP Safety a 2N® IP Uni). If a speaker is not integrated in the
device, make sure than an external speaker is connected (2N® IP Audio Kit and
2N® IP Video Kit) to use sound signaling.
Services
The Services tab displays the status of the network interface and selected
services.
28 / 283
Configuration manual for 2N IP intercoms 29 / 283
Configuration manual for 2N IP intercoms License
The License tab displays the list of licensed functions of the intercom
including their current availability (on the basis of a valid license key
entered in the System | License menu).
30 / 283
Configuration manual for 2N IP intercoms Access Log
The Access Log tab displays the last 10 records on applied cards. Each record
includes the card tapping time, card ID and type and description details
(validity, card owner, etc.).
31 / 283
Configuration manual for 2N IP intercoms Call Log
The call log provides a list of all accomplished calls. Each call includes the
contact type, called/ calling user ID, call date and time, call duration and
status (incoming, outgoing, missed, picked up elsewhere, doorbell button). Use
the search box for fulltext search in the call name. Use the check box for
selecting all records for bulk deletion. The selected call record can also be
deleted individually using a button . The list includes the last 20 records
that are arranged from the latest call to the oldest one.
Events
The Events tab displays the last 500 logged events. Every event contains time
and date, event type and description specifying the event. The events can be
filtered by type in a dropdown menu, above the event log.
32 / 283
Configuration manual for 2N IP intercoms
·
press the button to export all recorded events to a CSV file.
Event
Description
AccessLimite d
Event generated after 5 unsuccessful user authentication atttempts (card, code, fingerprint). The access module gets blocked for 30 seconds even if the subsequent authetication is correct.
ApiAccessReq Generated whenever the request is sent to /api/accesspoint/grantaccess
uested
with the “success” : true result.
AccessTaken Card tapping in Anti-passback area.
AudioLoopTe Generated after the audio test indicating the test result. st
33 / 283
Configuration manual for 2N IP intercoms
Event
Description
CallSessionSt Event describing the call direction/state, address, session number and call ateChanged sequence number.
CallStateCha Indicates the call direction (incoming, outgoing) and opponent / SIP account
nged
identification at a call state change (ringing, connected, terminated).
CardHeld
Indicates that an RFID card has been held for more than 4s.
CardEntered Indicates that an RFID card has been tapped.
CodeEntered Generated whenever a code ending with * is entered via the numeric keyboard.
DeviceState Device state indication, startup of the device, for example.
DoorOpenTo Detection of a too-long opened door, settings in Hardware / Door / Door. oLong
DoorStateCh Door open/closed state detection. Settings can be made in Hardware / Door /
anged
Door.
DtmfEntered DTMF code received in call or off call locally.
DtmfPressed DTMF code pressed in call or off call locally.
DtmfSent
DTMF code sent in call or off call locally.
FingerEntere d
InputChange d
Fingerprint authorization. Signals a state change of the logic input.
KeyPressed
Generated whenever a button is pressed (numeric keypad digits are 0, 1, 2…, 9 and quickdial buttons are %1, %2 …).
KeyReleased Generated whenever a button is released (numeric keypad digits are 0, 1, 2…, 9 and quickdial buttons are %1, %2 …).
LiftFloorsEna Floor access via lift enabled. bled
34 / 283
Configuration manual for 2N IP intercoms
Event
Description
LiftStatusCha Detection of Lift Control module connection/disconnection. nged
LoginBlocked Event generated after 3 wrong logins to the web interface. Contains information about IP address.
MobKeyEnter Bluetooth authorization. ed
MotionDetect Generated after motion detection, settings can be made in Hardware /
ed
Camera / Internal Camera.
NoiseDetecte Generated after noise detection, settings in Hardware / Audio. d
OutputChang Signals a state change of the logic output. ed
RegistrationS Change of the SIP Proxy registration state. tateChanged
RexActivated Event at input activation set for the REX button.
SilentAlarm
Silent alarm event generated whenever a code higher by one than the correct one is entered. With access code 123, the silent alarm code is 124. Or, whenever a finger is placed on the fingerprint reader module designated for silent alarm activation.
SwitchesBloc Switches blocked by an invalid access attempt. ked
SwitchOperat Switch operation changed (signals switch lock/hold, timer start/restart/ ionChanged termination transition to permanent hold).
SwitchStateC Change of the switch state, settings in Hardware / Switches. hanged
TamperSwitc hActivated
Signals tamper switch activation device cover opening. Make sure that the tamper switch function is configured in the Digital Inputs | Tamper Switch menu.
Unauthorized Unauthorized door opening indication, settings in Hardware / Door / Door. DoorOpen
35 / 283
Configuration manual for 2N IP intercoms
Event
Description
UserAuthenti Signals user authentication and subsequent door opening. cated
UserRejected User rejection.
VirtualInput Virtual input change.
VirtualOutput Virtual output change.
CallSessionSt Informs of the current call phase (initialized, connecting, ringing, connected, ateChanged terminated).
5.2 Directory
Here is what you can find in this subsection: · 5.2.1 Users · 5.2.2 Time
Profiles · 5.2.3 Holidays
36 / 283
5.2.1 Users
Configuration manual for 2N IP intercoms
The Users list is one of the crucial parts of the intercom configuration. It
contains user information relevant for such intercom functions as quick
dialing, RFID card/code door unlocking, missed call e-mails and so on.
The Users list contains up to 10 000 users (variable in the 2N IP intercom
models). Also includes the users that can be called via the quick dial buttons
and the users that are assigned the RFID card, code, etc. access to the
building. If your external card reader is connected to the intercom via the
Wiegand interface, the card ID is shortened to 6 or 8 characters for
transmission (depending on the transmission parameters). If you apply a card
to the reader, you will receive a complete ID, which is typically longer (8
chars or more). The last 6 or 8 characters, however, are identical. This is
useful for comparing card IDs with the intercom database: if the IDs to be
compared have different lengths, they are compared from the end and match has
to be found in 6 characters at least. If they have identical lengths, all the
characters are compared. This ensures mutual compatibility of the internal and
external readers. All cards applied via the reader or the Wiegand interface
are recorded. Refer to the Status / Access Log menu for the last 10 cards
including the card ID/type, card tapping time and other information if
necessary. With small systems, you can make a trick to enter card IDs: tap the
card on the intercom reader and find it in the Access Log. Double-click to
select the card ID and push CTRL+C. Now that you have the card ID in your box,
you can insert it with CTRL+V in any intercom setting field. Having been read,
the card ID is compared with the intercom card database. If the card ID
matches any of the cards in the database, the appropriate action will be
executed: switch
37 / 283
Configuration manual for 2N IP intercoms
activation (door unlocking, etc.). To change the switch number to be
activated, use the Associated Switch parameter in the Hardware / Card Reader
menu (2N® IP Base, Vario, Force, Safety models) or the Associated Switch
parameter in the Hardware / Modules menu of the card reader module (2N® IP
Style, 2N® IP Verso model). Use the Hardware / Buttons menu to assign the
quick dial users. You can change the user and button settings as necessary.
Most of the 2N IP intercoms are equipped with one or more quick dial buttons.
Refer to the Installation Manual of your intercom model for the quick dial
button count and extending options.
Warning · You are not advised to edit the device directory that is managed by
2N® Access Commander via the device web interface. Due to synchronization with
2N® Access Commander the directory changes made via the web interface will be
lost.
38 / 283
Configuration manual for 2N IP intercoms
The Search in directory function works as a fulltext search in user names,
phone numbers and e-
mail addresses. It searches for all matches in the list. Press the button
above the table to add a User. Or, search a device in the LAN and then add the
device as a new contact to the Directory.
Click to show the user details. Click to set the table column display; the default table
setting displays the user name, e-mail and assigned accesses. Press to remove a user and
delete its details. The
icons in the access column describe the active user
authentications. The user’s position in the list is sorted alphabetically.
Using the / icon, it is possible to export/import from/into the device a CSV file including a user list. If the directory is empty, a file is exported with the header only (in English) to be used as a user importing template. If an empty file with the header only is imported and Replace directory is selected, the whole directory is deleted. All the users available in the directory are
39 / 283
Configuration manual for 2N IP intercoms
exported except for the special types of users. Up to 10,000 users can be
imported depending on the device type.
Caution · While editing the CSV file using Microsoft Excel, remember to save
the file in the CSV UTF-8 format (with separators).
Every record in the Users list includes the following parameters:
· Name mandatory parameter for easier user search, for example. · Photo
load the user photo. Click the photo adding frame to display the Photo editor
to
load a photo from a file or create a user photo using an integrated camera.
The supported photo formats are .jpg, .png and .bmp. This function is only
available in display-equipped models: 2N® IP Style, 2N® IP Verso and 2N® IP
Vario.
40 / 283
Configuration manual for 2N IP intercoms
Caution · If the cropped image does not fill the whole crop window space, the
resultant picture is centered on 2N® IP Style.
· E-mail user e-mail address for sending missed call information. You can
enter more email addresses separated with commas.
· Virtual Number number to be used for user calling via a numeric keypad.
The number can have 2 to 4 digits. Virtual numbers are not associated with
user telephone numbers. They are included in an independent numbering plan
allowing you to withhold user telephone numbers, especially in installations
where the quick dial button count is insufficient. The visitor enters a
virtual number via the numerical keypad and presses the * key. You are
recommended to place a clear user/virtual number list nearby including simple
instructions for use to facilitate this type of user calls. Enable this
function Calling Virtual Numbers in the Services / Phone / Calls / Outgoing
calls menu. The number may include 17 digits.
· Position within a Phonebook the root directory is only created by default,
to which users from the directory can be added directly. The root directory
cannot be deleted or renamed. One user can be assigned to up to 5 root
directory subgroups.
· Call group enter a user group name to be displayed in the directory. By
dialing the group you make calls to all of its users at the same time. When
one call is answered, the other calls will be terminated automatically.
Caution · The <, > and / characters are not allowed for the Name, Position
within a Phonebook and Call group parameters.
41 / 283
Configuration manual for 2N IP intercoms
Each user in the list can be assigned up to three phone numbers. In case the
user is inaccessible on one number, the following number will be dialed after
a ringing timeout. Enable the Parallel call to following number to enable
dialing multiple numbers simultaneously. The phone
number validity can also be time profile-limited.
· Phone Number enter the phone number of the station to which the call shall be routed. Enter the address sip:[user_id@]domain[:port] for Direct SIP calling, e.g.: sip:200@192.168.22.15 or sip:name@yourcompany. For local calls to the 2N IP intercoms and answering units enter device:device ID. Set the device name in the respective devices. For calls to Crestron enter RAVA:device_name. Enter /1 or /2 behind the phone number to specify which SIP account shall be used for outgoing calls (account 1 or 2). Enter /S or /N to force an encrypted or unencrypted call respectively. Enter /B to activate door opening via Callback. Combine account selection, encryption and Callback door opening by e.g. /1S, /1B. etc. The parameter can contain up to 255 characters.
Click
to edit the phone number details.
42 / 283
Configuration manual for 2N IP intercoms
· Call Type set the scheme in the called destination URI. If you choose
Without scheme, the URI is completed with the data from the SIP account
settings. Further settings include direct SIP calls (sip:), 2N local calls
(device:), Crestron calls (rava:) or calls with video management systems, e.g.
AXIS Camera Station (vms:).
· Destination Set the other parts of the called destination URI. As a rule,
it contains the number, IP address, domain, port or device identifier. Enter
an asterisk (*) for calls to the VMS.
· Preferred SIP Account SIP account 1 or 2 is primarily used for calling. ·
Call Encryption set mandatory call encryption or no encryption. · Door
Opening via callbacks. · Time Profile assign a time profile to each phone
number to define the number validity. If the profile in inactive, the phone
number is not used and the following phone number is dialed if defined. · IP®
Eye Address set the address of the PC to be sent a special UDP message on
each active user phone number call. With the aid of this message, the 2N® IP
Eye application displays the camera image screen for those users who are not
provided with a displayequipped videophone. Enter the address as follows:
domain[:port1][:port2], e.g.: computer.yourcompany.com or 192.168.22.111. The
port1 and port2 parameters are optional and are used in case there is Network
Address Translation (NAT) between the PC and intercom and the addresses have
to comply with the router or another NAT-executing device. The port1 (default
value: 8003) parameter defines the destination port for the UDP messages sent
to 2N® IP Eye. The port2 (default value: 80) parameter defines the destination
port for the 2N® IP Eye intercom HTTP communication.
43 / 283
Configuration manual for 2N IP intercoms
Note · The ‘IP Eye Address’ function is available in selected 2N IP intercom
models only (refer to the model and license overview). · When Enhanced
Integration is not licensed on a device, it is possible to control the locks
only when a call is in progress. If a call with user, who has 2N® IP Eye
address filled in, is in progress, no license is needed to control the locks.
Tip · FAQ: 2N® IP Eye How to set
Tip · Video Tutorial: SW application for IP intercoms 2N® IP Eye
· Parallel call to following number enable group calling, i.e. calling to
more phone numbers at the same time. You can call the first two numbers, the
last two numbers, or all of the three user numbers in parallel. Answering one
call automatically terminates the other calls.
· Parallel call to following deputy enable group calling, i.e. calling to
more phone numbers at the same time. You can call the first two numbers, the
last two numbers or all of the three user numbers in parallel. Once one of the
calls is answered, the other calls are automatically terminated. The maximum
total count of numbers to be dialed in parallel is 16, which can occur when
group calling and multiple numbers assigned to a speed dial button are used
simultaneously.
· User Deputy select a user to which the user calls will be routed in the
event of inaccessibility. Enter the user position number or use the search
button. The maximum total count of calls to be dialed in parallel is 16, which
can occur when group calling and multiple numbers assigned to a speed dial
button are used simultaneously.
Note · The User Deputy function is available in selected 2N IP intercom models
only (refer to the model and license overview).
44 / 283
Configuration manual for 2N IP intercoms
· Entry Rules · Access Enabled enable authentication via this access point.
· Access Profiles select one of the profiles pre-defined in Directory / Time
profiles or set the time profile for this element manually.
· Exit Rules · Access Enabled enable authentication via this access point. ·
Access Profiles select one of the profiles pre-defined in Directory / Time
profiles or set the time profile for this element manually.
· Validity term · Valid from set the beginning of the mode validity term. ·
Valid to set the end of the mode validity term.
· Access Exception set an exception from the access blocking and Anti-
passback rules for the user.
45 / 283
Configuration manual for 2N IP intercoms
Each of the users can be assigned a unique private QR code / numerical code for switch activation. The user switch codes can be arbitrarily combined with the universal switch codes defined in the Hardware | Switches menu. If the codes are identical with the codes already defined in the intercom configuration, the mark will appear at the colliding codes.
· PIN Code set the user’s Personal Identification Number. The code must include 2 characters at least.
·
generate a QR code image. Codes shorter than 10 digits cannot be entered by
QR code reading for security reasons. The codes must contain digits only. If
authentication using a hexadecimal QR code is required, convert this code into the hexadecimal format before entering. Accepted hexadecimal range: 1000 to
FFFFFFFF. · Switch 14 set a private user switch activation code: up to 16
characters including digits
09 only. The code must include 2 characters at least. The code must include
at least two
door unlocking characters via the intercom keypad and at least one door unlocking
character via DTMF.
·
generate a QR code image. Codes shorter than 10 digits cannot be entered by
QR code reading for security reasons. The codes must contain digits only. If
authentication using a hexadecimal QR code is required, convert this code into the hexadecimal format before entering. Accepted hexadecimal range: 1000 to
FFFFFFFF.
Each of the intercom users can be assigned two access RFID card.
46 / 283
Configuration manual for 2N IP intercoms
· RFID Card ID set the user access card ID: 632 characters including 09,
AF. Each user can be assigned up to two access cards. When a valid card is
tapped on the reader, the switch associated with the card reader gets
activated. If the double authentication mode is enabled, the switch can only
be activated using both a card and numeric code.
· Virtual Card ID set the user virtual card ID for user identification in
the devices that are integrated with the 2N IP intercoms via a Wiegand
interface. Each user can be assigned just one virtual card. The virtual card
ID is a sequence of 632 characters: 09, AF. After the user is validated via
the Bluetooth/biometric reader, the identifier is sent to the device
integrated with the 2N IP intercom via Wiegand.
· Auth ID set a unique mobile device/user identifier. The parameter value is
automatically generated for pairing. You can move Auth ID to another user or
copy it to another device in
the same location. · Pairing State display the current pairing state
(Inactive, Waiting for pairing, PIN validity
expired or Paired). · Pairing valid until display the date and time of the
generated authorization PIN validity
end.
·
pair via USB reader
·
pair via this device
·
delete Auth ID
Pairing via Bluetooth Module in Intercom
To pair a mobile phone with the user:
· Click
at Auth ID to start pairing for the selected user account.
· A dialogue window with the PIN code is displayed.
· Find the appropriate reader in the 2N® Mobile Key application and press Start pairing. · Enter the code from item 2 into the input field.
· Pairing is completed.
47 / 283
Configuration manual for 2N IP intercoms
Refer to 5.4.5 Mobile Key for 2N® Mobile Key configuration details.
48 / 283
Configuration manual for 2N IP intercoms
· User Fingerprints display the set count of fingerprints; up to 2 different fingerprints can be set. This section is displayed only if the biometric reader module is available.
·
enroll via USB reader
·
enroll via Fingerprint scanner module 3
Caution · The fingerprint loading capacity is up to 2000 per device.
Refer to Subs. 5.2.1.1 User Fingerprint Setting Instructions for user
fingerprint loading details.
The 2N IP intercom helps you use the recognized license plates sent in the
HTTP request by the AXIS cameras equipped with additional VaxALPR to
api/lpr/licenseplate (refer to the HTTP API Manual for IP Intercoms for more
details). In case the function is on, the event is recorded into the
LicensePlateRecognized history when a valid HTTP request has been received.
If an image is sent within the HTTP request (photo part or whole photo of the
license plate detecting scene), it is saved. The last five photos are stored
in the device memory and can be retrieved via an HTTP request sent to
api/lpr/image available in 2N® Access Commander.
It is advisable that each license plate should be assigned to just one entry
in the directory. Multiple license plate assignments may result in the
inability to assign a license plate to an entry in the directory unambiguously
(the first entry assigned the specified license plate is selected and given
the access rights).
· License Plates set the car license plates for the selected entry in the
directory. An entry can be assigned multiple license plates separated with
commas (up to 20). The set license plates are used for recognizing license
plates from external camera images (refer to the Interoperability Manual for
details). One license plate may include up to 10 characters. The set string
length is limited to 255 characters.
49 / 283
Configuration manual for 2N IP intercoms
· Floors select the floors available to the user. · Time Profile select
one or more time profiles to be applied. Set the time profiles in the
Directory / Time Profiles section.
·
mark the selection from predefined profiles or manual setting of a time profile
for the given element.
·
set a time profile for the given element.
50 / 283
Configuration manual for 2N IP intercoms
5.2.1.1 Call Connection Settings
To make calls with other terminal devices in IP networks, it is necessary to
assign the device to a contact in the Directory.
Connection with 2N Devices in LAN
1. Make sure that Local calls is enabled on both the 2N devices. 2. Click
Find device above the table. Check the listed device that you want to make
connection to. Once the device is added, the new user can be edited. 3. You
can edit basic user information or manage user access options. Set a virtual
number
for the user if you want to use a numerical keypad for dialing calls. 4. Once
saved, the contact will be shown in the phone book on the device display. To
dial
calls with a device button, assign the selected user to the quick dial button
in Hardware > Buttons, refer to 5.3.5 Tlacítka. 5. Make sure that Local calls
is enabled on the called 2N device to make a successful call.
Connection with Other Devices
1. Click Add user above the table to create a new contact or open an existing
contact detail. 2. Click the pencil icon next to the Phone number to open
phone number editing. 3. Select the type of call:
· SIP for calls via SIP, · rava for calls with Creston, · vms for calls with
Axis Camera Station, · device for calls with a local 2N device. 4. Enter the
calling destination address into the destination field to which the call is to
be routed. Complete SIP URI in the format user_name@host or the target IP
address (e.g.: johana@255.0.255.0 or johana@calls.2N.com). For local calls,
fill in the called 2N device ID, refer to Local Calls in 5.4.1 Phone. 5. You
can edit basic user information or manage the user access options. Set a
virtual number for the user if you want to use a numerical keypad for dialing
calls. 6. Once saved, the contact will be shown in the phone book on the
device display. To dial calls with a device button, assign the selected user
to the quick dial button in Hardware > Buttons, refer to 5.3.5 Buttons. 7.
Make sure that the call transmitting service is enabled on the called device
to make a successful call.
51 / 283
Configuration manual for 2N IP intercoms
Tip · Each user can be assigned up to 3 phone numbers. In case the first user
fails to answer, the call is forwarded to the next number. Alternatively, you
can set calling to multiple phone numbers simultaneously. Check Call in group
between the selected numbers to set such multiple phone number calling for one
user. · In case all the user phone numbers are unavailable, you can set call
forwarding to Deputy. · Users can be gathered in calling groups. The calling
group name is shown in the phone book on the device display. You can assign a
calling group to a quick dial button. To terminate an outgoing group call
after the first rejection from any of the called users, set this function in
Services > Phone > Calls, refer to 5.4.1 Phone.
5.2.1.2 User Fingerprint Setting Instructions
To load fingerprints, use the 2N® IP Verso (Part No. 9155045) fingerprint
reader or an external USB fingerprint scanner (Part No. 9137423E) as follows:
1a) To load fingerprints via the 2N® IP Verso reader, use the web interface at
the selected user and click Load via fingerprint reader module in Directory /
Users/ User fingerprints.
1b) To load fingerprints via an external USB fingerprint scanner, use the 2N®
IP USB Driver and select Fingerprint reader in the Settings and press OK for
confirmation. Click Load via fingerprint reader module in Directory / Users/
User fingerprints via the web interface at the selected user.
52 / 283
Configuration manual for 2N IP intercoms 53 / 283
Configuration manual for 2N IP intercoms
2) Click to select a finger for fingerprint loading.
Up to two fingerprints may be saved for each user. 3) Click SCAN FINGER to
load a fingerprint.
54 / 283
Configuration manual for 2N IP intercoms
4) Place the selected finger on an external USB reader. This process is
repeated three times for greater precision.
Repeat the process if any inconsistency occurs during fingerprint reading.
55 / 283
Configuration manual for 2N IP intercoms
5) If fingerprint scanning is successful, click DONE to confirm the settings.
To set the finger function, click the icon to display the list of available
functions: · Open door · Silent Alarm; only if Open door is active ·
Automation F1 generate the FingerEntered event in Automation. F1 helps
identify the fingerprint in Automation. · Automation F2 generate the
FingerEntered event in Automation. F2 helps identify the fingerprint in
Automation.
56 / 283
Configuration manual for 2N IP intercoms
Click SAVE AND QUIT to confirm the fingerprint enrolment and selected
functions. 6) You can check the current settings in the User tab.
57 / 283
Configuration manual for 2N IP intercoms 5.2.1.3 USB RFID Card Reader
It is possible to read the card ID via an RFID card reader. Proceed as
follows: · Go to the 2N USB Driver settings. · Set up the COM port for the
connected reader.
· Press the Read button via the 2N IP intercom web interface.
58 / 283
· Tap the card on the card reader.
Configuration manual for 2N IP intercoms
· The card ID is successfully read. Do not forget to save the configuration.
59 / 283
5.2.2 Time Profiles
Configuration manual for 2N IP intercoms
Such intercom functions as outgoing calls and RFID card/numeric code access,
for example, can be time-limited by being assigned a time profile. By
assigning a time profile you can:
· block all calls to a selected user beyond the set time interval · block
calls to selected phone numbers beyond the set time interval · block RFID
access for a user beyond the set time interval · block numeric code access for
a user beyond the set time interval · block switch activation beyond the set
time interval Assign a time profile according to a week time sheet to define
availability of the selected function. Just set from-to or days in the week on
which the function shall be available. 2N IP intercom helps you create up to
20 time profiles (depending on the 2N IP intercom model) that can be assigned
to the function; refer to the Users, Access Cards and Switches settings. The
time profiles are defined not only using the week time sheet but also manually
with the aid of special activation/deactivation codes that you can assign to
them after arriving in/before leaving your office, for example. Enter the
activation/deactivation codes using the numeric keypad of your intercom or
phone (during the intercom call). Refer to the Directory / Time Profiles menu
for the time profile settings.
60 / 283
List of Parameters
Configuration manual for 2N IP intercoms
· Profile name enter a profile name. This parameter is optional and helps you find items in the time profile list and select profiles in the switch, card and phone number settings more easily.
This parameter helps you set time profiles within a week period. A profile is
active when it matches the set intervals.
61 / 283
Configuration manual for 2N IP intercoms
If a day is marked as holiday (refer to Directory Holidays), the last table
row (Holiday) is applied regardless of the day in a week. Make sure that the
real time settings are correct (refer to the Date and Time subsection) to make
this function work properly.
Note · You can set any number of intervals within a day: 8:0012:00,
13:0017:00, 18:00 20:00, e.g. · To make a profile active for the whole day,
enter one day-covering interval: 00:00 24:00.
62 / 283
5.2.3 Holidays
Configuration manual for 2N IP intercoms
Here select the bank holidays (including Sundays). You can assign them
different time intervals than to working days in their time profiles.
You can set holidays for the coming 10 years (click the year number at the top
of the screen to select a year). The screen displays a calendar for the whole
year for you to select/unselect a holiday. Fixed (annual) holidays are marked
green and variable holidays (valid for the particular year only) are blue.
Click a date once to select a fixed holiday, click twice to select a variable
holiday and click for the third time to remove the holiday from the holiday
list.
63 / 283
5.3 Hardware
Here is what you can find in this section: · 5.3.1 Switches · 5.3.2 Audio ·
5.3.3 Camera · 5.3.4 Keypad · 5.3.5 Buttons · 5.3.6 Backlight · 5.3.7 Display
· 5.3.7.1 2N® IP Style Display · 5.3.8 Card Reader · 5.3.9 Digital Inputs ·
5.3.10 Extenders · 5.3.11 Lift Control
Configuration manual for 2N IP intercoms
64 / 283
5.3.1 Switches
Configuration manual for 2N IP intercoms
Switches provide a very flexible and efficient control of such intercom
peripherals as electric door locks, lighting, additional ringing signalling,
and so on. 2N IP intercoms allows you to configure up to 4 (depending on model
types) independent all-purpose switches. A switch can be activated:
· by entering the valid code via the intercom numeric keypad or receiving a
DTMF sequence during a call.
· by tapping a valid RFID card on the reader. · with a predefined delay after
another switch activation. · by an incoming or outgoing call. · by pressing a
quick dial button ). · by a time profile ). · by receiving the HTTP command
from another LAN device. · via Automation using the Action.ActivateSwitch
action ). Switch activation can be blocked by an appropriately selected time
profile if necessary.
Caution · The options marked with ) require their respective active licences.
Switch locking and hold The switch activation conditions are modified using
two functions: switch locking and switch hold. If a switch is locked, it is
permanently deactivated and cannot be operated until unlocked (locked has a
higher priority than held in case the switch is locked and held
simultaneously, locking is applied). If held, the switch is in the activated
state and cannot be operated until
65 / 283
Configuration manual for 2N IP intercoms
released. Switch locking and holding can be controlled by time profiles among
others. It is not recommended that a time profile be used for the locking
function (the time-profile based lock control is present in the device for
legacy switch compatibility reasons) because this case results in switch
unlocking at the end of the time profile despite manual switch locking. The
current combination of these two functions is shown by the Current switch
function parameter (Normal lock and hold are off; Held lock is off and
hold is on; Locked lock is on regardless of the hold setting). Check after
restart whether or not the lock/hold is controlled by a time profile. If so,
the given function is activated/deactivated according to the time profile
setting. If not, the last locking state before the device power off is set, or
hold is set to inactive (the switch is not held). If a switch is active, you
can:
· activate any logical output of the intercom (relay, power output). ·
activate the output to which the 2N® IP Intercom – Security Relay module is
connected. · send an HTTP command to another device. The switch can work in
the monostable or bistable mode. The switch is switched off after a timeout in
the monostable mode and switched on with the first activation and off with the
next activation in the bistable mode. The switch signals its state: · by a
programmable beep or a predefined user sound. · by a LED indicator if
available in the intercom model. · by an open-door icon on the display if
available in the intercom model.
66 / 283
Switch 14
Configuration manual for 2N IP intercoms
· Switch Enabled enable/disable the switch globally. When disabled, the switch cannot be activated by any of the available codes (including user switch codes), by a call or quick dial button.
· Switch Mode set the monostable/bistable mode for the switch. The switch is
switched off after a timeout in the monostable mode and switched on with the
first activation and
off with the next activation in the bistable mode. · Switch-On Duration set
the switch-on time for a monostable switch. This value is not
applied in the bistable mode. · Controlled Output assign an electric output
to the switch. Choose one of the available
intercom outputs: relay, power output, extender output. If you select None,
the switch will not control any electric output but can control external
equipment via HTTP commands.
· Output Type if you use the 2N® IP Intercom Security Relay module, set
the output type to Security. In the Security mode, the output works in the
inverse mode, i.e. remains closed and controls the 2N® IP Intercom Security
Relay module using a specific pulse sequence. If you use the inverse mode
(i.e. the door is locked when voltage is applied), set the inverse output
type. In case multiple switches are set to the same output but different
output types, the following priority will be applied: 1. security, 2. inverse,
3. normal.
67 / 283
Configuration manual for 2N IP intercoms
Caution · 2N® IP Vario be sure to set the internal power supply and
switching relay on the configuration connector. 2N® IP Force the security
relay is connected to the DOOR + and – terminals. · A switch activation value
higher than 1 s can be set for the security output type. A value equal to or
higher than 0.1 s can be set for the normal and inverse output types.
Security · The 12V output is used for lock connection. If, however, the unit
(2N IP Intercom, 2N Access Unit) is installed where unauthorized tampering may
happen, we strongly recommend that the 2N® Security Relay (Part No. 9159010)
be used for enhanced installation security.
· Current Switch State display the current switch state (On/Off). · Current
Switch Function display the current switch function.
· Normal: the switch is not locked or held. · Held: the switch is held and
unlocked. · Locked: the switch is locked (locking has priority over holding,
the holding state is
irrelevant in this case). · Switch Locking on: the switch is permanently in
position 0 and cannot be controlled
until unlocked. Off: the switch is unlocked. · Switch Hold on: the switch is
permanently in position 1 and cannot be controlled until
released (if the switch hold and lock are active at the same time, the switch
is locked). Off: the switch not held in position 1. · Switch Hold by Time
Profile assign a predefined time profile to the switch or set a time profile
manually that allows for switch activation. If the assigned time profile is
inactive,
68 / 283
Configuration manual for 2N IP intercoms
the switch can be activated by tapping a valid RFID card, making a call,
entering a code or pressing a quick dial button. · Test the switch activate
the switch manually to test its function, e.g. an electric lock or another
device connected. Caution
· In case the switch is locked and the device is turned off and on, the switch
will be locked after the device is turned on again. The same is true when the
switch is disabled and enabled again.
· In case the switch is held and the device is turned off and on, the switch
will not be held after the device is turned on again. The switch is held after
power on only if a switch hold time profile is set and active at the moment of
the power on. The same is true when the switch is disabled and enabled again.
The table above includes a list of universal codes that help you activate
switches from the phone or intercom keypad. Up to 10 universal codes can be
defined for each switch (depending on the particular intercom model).
· Code enter the numerical code for the switch. The code must include at
least two door unlocking characters via the intercom keypad and at least one
door unlocking character via DTMF. We recommend you to use four characters at
least. Codes 00 and 11 cannot be entered and are not accepted from a numeric
keypad; they are reserved for opening doors via DTMF. Confirm the code with *.
The code length is up to 16 characters.
· Accessibility block the switch activation code entering from the intercom
numeric keypad or your phone.
· Time Profile assign a time profile to the switch code for validity
control. · Distinguish on/off codes set a switch code mode in which odd
codes (1, 3 ….) are used
for switch activation and even codes (2, 4 …) are for switch deactivation.
This mode can only be used if the switch is set to the bistable mode.
69 / 283
Configuration manual for 2N IP intercoms
· Activation by Call enable switch activation by an incoming or outgoing
call, for example. During an outgoing call the switch is activated after SIP
message 180 Ringing is received. The called party confirms ringing by this
message. The switch is active during the whole call in the bistable mode and
activated by the call beginning and deactivated after the predefined switch-on
duration in the monostable mode.
· Activation by Quick Dial Button assign a quick dial button to the switch.
The switch is activated whenever the button is pressed.
Note · Activation by a quick dial button is available with the Gold.
· Synchronise with set switch synchronisation to enable automatic switch
activation after another switch activation with a predefined delay. Define the
delay in the Synchronisation delay parameter.
· Synchronisation Delay set the time interval between synchronised
activations of two switches. The parameter will not be applied if the
Synchronise function is disabled.
70 / 283
Configuration manual for 2N IP intercoms
· Switch-On Command set the command to be sent to the external device (WEB
relay, e.g.) upon switch activation. The command is sent via the HTTP (GET
request) and must be as follows: http://ip_address/path. E.g.:
http://192.168.1.50/relay1=on.
· Switch-Off Command set the command to be sent to the external device (WEB
relay, e.g.) upon switch deactivation. The command is sent via the HTTP (GET
request) and must be as follows: http://ip_address/path. E.g.:
http://192.168.1.50/relay1=off
· Username enter the username for the external device (WEB relay, e.g.)
authentication. The parameter is obligatory only if the external device
requires authentication.
· Password enter the external device (WEB relay, e.g.) authentication
password. The parameter is obligatory only if the external device requires
authentication.
71 / 283
Configuration manual for 2N IP intercoms
The HTTP commands do not add URL encoding. If, e.g., you enter
http://10.27.24.6/ message.cgi?action=9%3A%2F, the following is
sent:http://10.27.24.6/message.cgi? action=9%3A%2F. To include URL encoding,
enter, e.g.: http://10.27.24.6/message.cgi? action=9%253A%252F and the
following is sent: http://10.27.24.6/message.cgi? action=9%253A%252F.
Tip With an external relay, Part No. 9137410E, the following HTTP commands are
used: To turn on the switch http://ip_address/state.xml?relayState=1 (e.g.:
http:// 192.168.1.10/state.xml?relayState=1) To turn on for pre-defined time
(default value is 1.5 s) http://ip_address/state.xml? relayState=2 (e.g.:
http://192.168.1.10/state.xml?relayState=2) To turn off
-http://ip_address/state.xml?relayState=0 (e.g.: http://192.168.1.10/
state.xml?relayState=0) With an external relay, Part No. 9137411E, the
following HTTP commands are used (replace the X symbol with the relay number):
To turn on the switch http://ip_address/state.xml?relayXState=1 (e.g.:
http:// 192.168.1.10/state.xml?relay1State=1) To turn on for pre-defined time
(default value is 1.5 s) http://ip_address/state.xml? relayXState=2 (e.g.:
http://192.168.1.10/state.xml?relay1State=2) To turn off
-http://ip_address/state.xml?relayXState=0 (e.g.: http://192.168.1.10/
state.xml?relay1State=0)
Advanced
· Legacy Switch Code enable the option to activate the first-listed switch
code from the phone without being confirmed with . When this box is checked,
first code does not require confirmation by . This setting does not apply to
other switch codes listed and to numeric keypad code activation, those must be
always confirmed by *. The Legacy switch code helps you keep back
compatibility with earlier 2N intercom models.
72 / 283
Configuration manual for 2N IP intercoms
· Output 1 Maximum Power set the maximum output 1 power value.
73 / 283
5.3.2 Audio
Configuration manual for 2N IP intercoms
All the 2N IP intercom models are equipped with a speaker or power amplifier output to which an external loudspeaker can be connected. Set the phone call and state signalling volume control in this configuration section. Set the Master volume to control the master volume of the device: volume of calls, signalling tones, etc. Set this parameter according to the ambient noise level. If the noise level is not constant, use the Adaptive mode to increase the master volume temporarily depending on the ambient noise level.
Model
Master Volume
IP Style
-12 dB .. +8 dB (2 x 4 W)
IP Vario
-10 db .. +0 dB (150 mW)
Force/Safety 1W
-12 dB .. +6 dB (1 W)
Force/Safety 10W
-12 dB .. +20 dB (10 W)
IP Uni
-12 dB .. +6 dB (1 W)
IP Verso
-8 dB .. +8 dB (2 W)
IP Solo
-8 dB .. +4 dB (2 W)
74 / 283
Model
IP Base Audio/Video Kit SIP Speaker SIP Speaker Horn
List of Parameters
Configuration manual for 2N IP intercoms
Master Volume
-8 dB .. +8 dB (2 W) -10 dB .. +10 dB -10 dB .. +10 dB -16 dB .. +16 dB
· Master volume set the master volume for the entire system. This setting affects the volume of phone calls and all signalling tones.
· Adaptive volume enable the adaptive volume mode in which the speaker
volume is adjusted automatically depending on the noise level of the intercom
installation site.
· Maximum gain set the maximum gain to be applied to the master volume in
the adaptive mode.
· Sensitivity threshold set the ambient noise threshold at which adaptive
gain is applied. · Current noise level display the current ambient noise
level.
75 / 283
Configuration manual for 2N IP intercoms
· Current adaptive gain display the current adaptive gain of the master
volume. The value is determined by the difference of the Current noise level
and Sensitivity threshold and never exceeds the Maximum gain value.
· Ringtone volume set the incoming call signal loudness. · Call-progress
tone volume set the dial, ring and busy tone volume. In case the call-
progress tones are automatically generated by the PBX, this setting will not
be applied.
· Key beep volume set the key beep volume. The volume values are relative
against the set master volume.
· Warning tone volume set the volume of warning and signalling tones
described in the Signalling of Operational Statuses section. The volume values
are relative against the set master volume.
· Switch activation tone volume set the volume of the switch activation
tone. The volume values are relative against the set master volume.
· User sounds volume set the volume of the user sounds to be played. The
volume values are relative against the set master volume.
76 / 283
Configuration manual for 2N IP intercoms
· Default audio input set the default audio input (microphone, line input or
audio module input) to be used for phone calls and audio streaming.
· Microphone input gain set the microphone input gain. · Line input gain
set the line input gain independently of the microphone gain value. Tip
Only at 2N® SIP Speaker Horn, 2N® IP Audio Kit and 2N® IP Video Kit is
possible to configure microphone gain. The microphone/line input gain setting
is connected with the input signal level and type of external microphone
installation. The wide gain range (0 to 39dB for a microphone input and -6dB
to 24dB for a line input) should be sufficient for most installations. Set a
value to ensure good audibility and eliminate excessive acoustic feedback at
high loudspeaker volumes with subsequent signal saturation on the
microphone/line input and thus acoustic echo cancellation (AEC) deterioration.
· Acoustic feedback filter set automatic suppression of acoustic feedback
(typically whistling) between the intercom speaker and phone handset if
located in close proximity to the intercom. This mode is disabled by default.
77 / 283
Configuration manual for 2N IP intercoms
· Noise Detection Enabled switch on automatic detection of noise or
microphone noise level threshold exceeding. Process the threshold exceeding
alarm using Event.NoiseDetected and assign it to other user actions.
· Noise Level Threshold set the microphone noise level threshold for alarm
setting. · Alarm Start Delay set the time interval during which the signal
must be above the
threshold to start alarm. · Alarm End Delay set the time interval during
which the signal must be below the
threshold to stop alarm. · Noise Level Graph display the signal level
history. Red designates alarm activation.
78 / 283
5.3.3 Camera
Configuration manual for 2N IP intercoms
This menu is only available in the 2N IP intercom models that are equipped
with an internal camera or can be connected to an external camera. The camera
signal can be streamed directly into the call via a videophone, sent by
E-mail, streamed via ONVIF/RTSP to another device (a video surveillance
device, e.g.), or simply HTTP downloaded from the intercom in the JPEG format.
The following video signal sources can be used:
· an internal integrated camera or external analog camera (2N® IP Video Kit
only) · a standard external IP camera supporting RTSP stream with codecs MJPEG
(640 x 480 max
resolution) or H.264 (640 x 480 Base Line Profile max resolution). The
recommended framerate is 15 frames per second in either case. Higher frame
rates may result in undesired effects (less smooth playing). The Camera menu
helps you set such camera parameters as brightness, color saturation and
external IP camera login data if necessary. Refer to the Services / Phone,
Services / Streaming and Services / E-Mail menus for the video call/streaming
parameters.
Common Settings
· Default Video Source set the default video signal source. Choose Internal
camera (or an analog camera connected to the intercom) or External IP camera.
The change of the default video signal source is applied to the RTSP stream
and HTTP API. In 2N® IP Eye it is required to enable the external camera
manually, even when there is no internal camera
79 / 283
Configuration manual for 2N IP intercoms
present in the device. If no internal camera is connected to the intercom,
External IP camera can only be selected. If the external camera is not
connected or configured properly, N/A is displayed on a blue background. ·
Live Preview display a live preview from a 2N IP intercom camera.
Internal Camera
· Brightness Level set the camera image brightness level. · Exposure Level
set the image exposure level (higher values mean that a longer exposure
time is preferred by the device). · Contrast set the camera image contrast.
The parameter is only available in the 2N® IP
Style model. · Color Saturation set the camera image color saturation. ·
Camera Mode select suitable camera modes according to the current intercom
installation conditions (indoor/outdoor use). Choose variable image flicker
cancellation modes for indoor sites illuminated by artificial light. Or, set
direct sunshine suppression for outdoor applications. · Automatic Framerate
Decreasing enable automatic frame rate decreasing under worsened
illumination conditions to improve image quality by lowering the frame rate. ·
Image Trimming the 2N® IP Force camera view angle allows you to scan the
largest area possible. Use this parameter to enable automatic camera image
trimming to eliminate the (sometimes annoying) view of the intercom frame.
Disable this function to get the maximum possible view angle. The parameter is
available in the 2N® IP Force models only. · Day/Night Mode set the camera
day/night mode. The options are automatic (controlled by the ambient light
level), or permanently day or night mode.
80 / 283
Configuration manual for 2N IP intercoms
· Current Mode display the currently selected camera mode (day/night). In
the day mode, the camera uses an IR suppressing filter and infrared
illumination is disabled. In the night mode, the IR suppressing filter is
disabled and infrared illumination is on.
· IR LED Brightness Level set the infrared LED brightness level in the range
of 0-100% in several steps. Infrared illumination is automatically activated
in night mode. The IR LED brightness level settings are only available in the
2N® IP Style, 2N® IP Verso and 2N® IP Force with HD camera models.
· Current IR LED Brightness Level display the current IR LED brightness level
percentage. The level can automatically be decreased below the set value so
that the maximum power consumption cannot be exceeded (typically, when
multiple extenders are connected and PoE supply is used).
· Live Preview display a live preview from a 2N IP intercom camera.
The Advanced Settings menu is available for the 2N® IP Style intercom model. ·
Image Correction set the digital correction (flattening) for the device
internal camera. · Custom Image Crop sets default centered scene crop
(margins are symmetrically cropped). · White Balance set the fixed white
balance according to the prevailing light source where the automatic white
balance is insufficient (an improperly chosen white balance method leads to an
undesired image discoloration). · WDR Allowed you are advised to enable WDR
(Wide Dynamic Range) in case there are very dark places as well as highly
illuminated spots on the scene. The WDR ensures that the whole scene is seen.
· Local Contrast set a higher level to increase the contrast of the boundary
between the bright and dark spots on the scene. · Tone Mapping set a higher
level to increase the contrast of the boundary between the bright and dark
spots on the scene. · Exposure Time Limit set the maximum time span for an
image to be exposed and created. Where more light is available, the shutter
does not have to be open for the whole time and the camera sets a shorter
shutter speed automatically.
81 / 283
Configuration manual for 2N IP intercoms
Caution · Having changed the Custom image crop parameter for devices with the
ARTPEC-7 chip set, check the limits of the motion detection and privacy
masking areas, which will change spatially, see the picture.
Note · This setting is only available in the models equipped with an external
analog camera input.
· Video Input choose one of the analog camera inputs. You can change the
input by automation via the Action.SetCameraInput during operation.
· Video Standard set the video standard for the camera connected. Modify the
value only if the automatic video standard detection does not work well (Auto
value).
· Motion Detection Enabled enable automatic motion detection via an internal
camera. Motion is detected by monitoring of a brightness change in the
selected image section in time. When objects move within the camera range, the
selected part of the image detects an activity, which can be expressed in
percentage. If the activity exceeds the upper limit, motion is detected and
indicated as long as the activity drops below the lower limit. Select the
sensitivity thresholds and detection area according to the requirements and
installation site conditions.
82 / 283
Configuration manual for 2N IP intercoms
· Sensitivity Threshold set the lower and upper sensitivity and hysteresis
limits for the motion detecting algorithm.
· Detection Area set the rectangular detection area in the image. · Activity
Graph display the activity history (image brightness changes) including the
upper/lower sensitivity thresholds. Motion Detection and Privacy with ARTPEC-7
Equipped Devices
· Motion Detection Profile 1/2 Enabled enable automatic motion detection
from an internal camera image. Motion detection is based on a change of the
brightness component in the selected image section in time. Any movement
within the camera detection area results in a change of a certain part of the
image. If the activity exceeds the upper sensitivity threshold, motion is
indicated. Motion is indicated until the activity drops below the lower
sensitivity threshold.
83 / 283
Configuration manual for 2N IP intercoms
· Detection Area set the rectangular detection area in the image. · Activity
Graph display the activity detection history on as time axis. Green means no
motion, grey means motion detection that fails to meet the set criteria and
red means motion detection that meets the criteria. · Mode the event
triggering mode is designed to generate short motion detection events for
actions, e.g. image uploading. The uploading mode is configured to generate
longer events, for ONVIF uploading, for example. · Minimum Inactive Time set
the minimum inactive time interval between two motion detection events to
prevent generation of too many events in quick succession. · Filter Objects
with Duration Less than set the minimum time in seconds during which motion
has to be detected continuously for the motion detection event to be
generated. The setting range is 1 to 5 seconds. The motion must meet the
conditions set in this section. · Filter Objects with Width Less than set
the minimum width of the objects to be detected in relation to the whole
camera image width for the event to be generated. The setting range is 3 to
100 %. The motion must also meet the other conditions set in this section. ·
Filter Objects with Height Less than set the minimum height of the objects
to be detected in relation to the whole camera image width for the event to be
generated. The setting range is 3 to 100 %. The motion must also meet the
other conditions set in this section.
84 / 283
Configuration manual for 2N IP intercoms
· Filter Swaying with Amplitude Less than set the minimum amplitude of
swaying objects in relation to the whole camera image width/height that has to
be exceeded for the object to be detected (the setting has no influence on
non-swaying objects). The setting range is 3 to 20 %. The motion must also
meet the other conditions set in this section.
Caution · In ARTPEC-7 equipped devices, moving objects are evaluated even
beyond the active zone including the set filters (if Custom Image Crop is
enabled, objects are evaluated even in the cropped image parts that cannot be
seen in the preview). The objects that enter the active area trigger a
detected motion event. For example, if the time filter is set to 5 s, any
object moving beyond the active area for 10 s triggers a detected motion the
moment it enters the active area, because it has met the filter condition
beyond the active zone. The object keeps being detected even if it leaves the
active zone and having re-entered the active area, it triggers the event
instantaneously (unless it leaves the camera image area completely and is
‘forgotten’).
· Privacy Masking Enabled enable privacy masking to mask an image section
with the green color or mosaic.
· Masking Mode set the color / mosaic for the masked area. · Mosaic Cell
Size set the mosaic cell size in the masked area. · Privacy Masking Area
set the privacy masking area position and size.
85 / 283
Configuration manual for 2N IP intercoms
Caution · Privacy masking may limit other functions, e.g. QR code reading or
motion detection. We do not recommend the use of privacy masking together with
the aforementioned functions.
External Camera
· External Camera Enabled enable RTSP stream download from the external IP
camera. Complete the valid RTSP stream address or the username and password to
make the function work properly.
· RTSP Stream Address enter the IP camera RTSP stream address: rtsp://
camera_ip_address/parameters. The parameters are specific for the selected IP
camera model. If you choose another 2N IP intercom for the external camera,
enter http:// ip_address/mjpeg_stream or http://ip_address/h264_stream.
· Username enter the username for the external IP camera authentication. The
parameter is obligatory only if the external IP camera requires
authentication.
· Password enter the external IP camera authentication password. The
parameter is obligatory only if the external IP camera requires
authentication.
· Local RTP Port set the local UTP port for RTP stream receiving. Tip
· FAQ: External camera How to set it in 2N IP intercom
86 / 283
Configuration manual for 2N IP intercoms
The Camera Preview window displays the current image received from an external
camera. If the external camera is disconnected or configured incorrectly, the
N/A characters are displayed on a blue background.
The External IP Camera Log displays the RTSP communication with the selected
external IP camera including failures and error states if any.
87 / 283
5.3.4 Keypad
Configuration manual for 2N IP intercoms
This configuration section helps you set the numeric keypad and quick dial
button functions. 2N IP intercoms allows you to:
· use the numeric keypad for making calls by dialing a virtual user number ·
use the numeric keypad for entering the access code for door unlocking, e.g. ·
set the # function · set the timeout for entering codes and phone numbers ·
set the function of the buttons and keys of the connected 2N® IP Audio/Video
Kit units
Keypad Mapping
The 2N® IP Audio Kit and 2N® IP Video Kit models are equipped with eight
terminals for up to 16 external buttons or a keypad. The functions can be set
for each button separately. The buttons and their settings are arranged in a
matrix of 4 columns x 4 rows; see the figure below. The figure below shows the
default button settings.
88 / 283
Configuration manual for 2N IP intercoms
You can assign one function to each matrix position: numeric keypad keys 0
through 9, *, # or one of the quick dial buttons 116.
89 / 283
5.3.5 Buttons
Configuration manual for 2N IP intercoms
Assign the Directory / Users users to the quick dial buttons. By default, all
available intercom buttons are assigned to the listed users. A non-assigned
button can be used for automation or switch activation, for example. In 2N® IP
Base models, however, first select the count of buttons in Hardware /
Extending modules.
· Clear Button Assignment clear all assignments of buttons to users.
90 / 283
Configuration manual for 2N IP intercoms
Display the list of all potentially available intercom buttons including those
physically absent. In some intercom models (2N® IP Vario, 2N® IP Verso), the
button list is divided into 8/5-item
groups corresponding to the button extending modules. Click , select the user
and press Add to add a user to the editing field. To search a user in the
list, use the fulltext field and the
username. One quick dial button can be shared by multiple users. Click
to test the set
quick dial button. A dialogue window is displayed including detailed information on the ongoing call (user, call direction, state, reason and last event time).
Info
· Up to 16 users can be assigned to one speed dial button. · The maximum total
count of numbers called in parallel is 16. This can occur in the
case of group call and multiple called users assigned to one quick dial
button.
91 / 283
5.3.6 Backlight
Configuration manual for 2N IP intercoms
This tab helps you control the backlight level of nametags, buttons and brightness of signaling LEDs.
If equipped with an ambient light level sensor, the intercom automatically chooses the suitable backlight level within the set range of values. The selected intercoms allow you to control the backlight brightness of name tags (buttons) and signaling LEDs (illuminated pictograms). Refer to the table below:
Property/ Model
2N® IP Style
2N® IP Verso / LTE Verso
2N® IP Solo
2N® IP Base
2N® IP Vario
2N®
2N® IP 2N®
IP
Safet IP
Force y
Uni
2N® IP Audio Kit
2N® IP Video Kit
Backlight
Yes
level control
Ambient
Yes
light level
sensor
Yes
Yes
No No
No No
92 / 283
Configuration manual for 2N IP intercoms
Property/ Model
2N® IP Style
2N® IP Verso / LTE Verso
2N® IP Solo
2N® IP Base
2N® IP Vario
2N®
2N® IP 2N®
IP
Safet IP
Force y
Uni
2N® IP Audio Kit
2N® IP Video Kit
Independen
Yes
Yes
No
No
t name tag
and LED
backlight
level control
The Backlight brightness settings are valid for the backlight intensity of the
main unit, buttons and extending modules.
The Signaling LEDs settings are valid for the signaling LEDs of the 2N® IP
Verso extending modules.
· Intensity by day set the LED intensity percentage value for the day mode.
· Intensity by night set the LED intensity percentage value for the night
mode. If the
Intensity by day and Intensity by night are set to one and the same value, the
ambient light level is ignored. · Current value display the current LED
intensity value automatically selected according to the ambient daylight
level.
93 / 283
Configuration manual for 2N IP intercoms
Note · The intensity brightness parameters affect the function, power
consumption and general appearance of your device. A high nametag and button
backlight value may, if the ambient light level is low, dazzle the persons
standing in front of the intercom and, in general, increase the power
consumption of the device. A low LED intensity value, on the other hand, may,
if the intercom is placed in direct sun, result in a lower LED on/off contrast
and potential LED state identification problems.
2N® IP Style Display Backlight Settings
The Backlight and Backlight in Low Power Mode settings are valid for the
display and ambient LED backlight.
· Intensity in Active Mode by Day set the maximum backlight intensity for
the daytime (the value is controlled by the ambient light sensor). Set the
value as a percentage of the maximum possible brightness.
· Intensity in Active Mode by Night set the maximum backlight intensity for
the night (the value is controlled by the ambient light sensor). Set the value
as a percentage of the maximum possible brightness.
· Current Value display the current backlight intensity value automatically
selected according to the ambient light level detected.
94 / 283
Configuration manual for 2N IP intercoms
· Lower intensity in Power Saving Mode to backlight intensity decrease when
the device has switched to the idle mode.
· Go to Low Power Mode in set the idle timeout (i.e. the time period during
which there are no interactions with the device) after which the low power
mode is automatically switched on. The setting range is 1 to 600 seconds.
· Go back from Low Power Mode set the interactions ways that allow for the
low power mode to be suspended. Choose between screen touch and between touch
or motion detection. Moreover, the device comes back from the low power mode
at user authentication, incoming calls and other operational statuses.
The Signaling LEDs settings are valid for the signaling LEDs (2N® IP Style
internal reader backlight).
· Intensity by Day set the signaling LED brightness value for the day mode.
Set the value as a percentage of the maximum possible LED brightness.
· Intensity by Night set the signaling LED brightness value for the night
mode. Set the value as a percentage of the maximum possible LED brightness. If
the Intensity by day and Intensity by night are set to one and the same value,
the ambient light level is ignored.
· Current Value display the current backlight intensity value automatically
selected according to the ambient light level detected.
95 / 283
5.3.7 Display
Configuration manual for 2N IP intercoms
Some intercom models (2N® IP Vario, 2N® IP Verso) can be equipped with a color
LCD display. The device state is displayed (call progress, door opening, etc.)
and the following modes are available: Display enable the display and
language settings for 2N® IP Vario and basic and language settings for 2N® IP
Verso. Directory display a configurable list of users. Use the numeric
keypad buttons (arrows) to go through the user list. You can create
practically any count of nested groups within the user list and add any count
of users to each group. Slideshow display a slideshow showing a set of
recorded images after a defined idle time. The automatic switching time can be
configured.
Display (for 2N® IP Vario only)
· Language set the language for the texts to be displayed. Choose one of the
predefined languages: English, Czech, German, Italian, French, Spanish,
Russian, Finnish, Danish,
96 / 283
Configuration manual for 2N IP intercoms
Polish, Dutch, Portuguese, Turkish, Norwegian, Swedish, Thai, Hebrew or a
custom language. · Phonebook Search Mode set the Phone Book searching mode.
You can search users either according to the first username characters (Prefix
only) or an arbitrary incidence of the selected characters in the username
(Arbitrary incidence). · Default Display Activation Timeout set the maximum
display idle time (i.e. during which the display is not controlled via the
buttons or numeric keypad) in which the Phonebook mode is switched to the Name
tag display if configured. Or, the 2N logo default window is displayed. ·
Showcase Mode set whether the device shall go into the showcase mode when
idle. Choose various options in the showcase mode (OFF, Slideshow). · Delay of
Showcase Mode Activation set the idle timeout in the range of 1 to 600
seconds after which the device goes into the Showcase Mode. There is always a
fixed 15second timeout for the device to return to the homescreen.
· Original Language download a preset XML file with all the texts to be
displayed. · User Language record, remove and load a localization file of
your own. · User Font record, remove and load a font of your own for the
texts to be displayed. Keep
the TTF format and make sure that the file does not exceed 4 MB. Note
If none of the pre-defined languages is convenient for you, proceed as
follows: · Download the original language file (English). · Modify the file
using a text editor (replace the English texts with your own ones). · Upload
the modified localization file to the intercom. · Set Language Settings |
Language to Custom. · Check and correct if necessary the texts on the intercom
display.
If you do not like the default graphic appearance of the name tags, upload a
background of your own to the intercom. Make sure that the image resolution is
320 x 240 pixels. Upload your name
97 / 283
Configuration manual for 2N IP intercoms
tags to the intercom to replace the original name tags. The original user
assignments, however, remain the same.
Display (for 2N® IP Verso only)
· Code Entering Keypad Button turn on the keypad display for entering
numeric codes. · Code Entering Keypad Mode set the keypad mode on the
display for entering numeric
codes. The modes include normal keypad and keypad with scrambled keys for
enhanced security. The setting is applied to the keypad even during multi-
factor authentication.
· Phone book Displayed enable/disable display of the phone book function. ·
Entry Keypad enable the keypad/keypad type.
· Disabled disable the keypad.
98 / 283
Configuration manual for 2N IP intercoms
· Regular Keypad set the regular keypad type. · Scrambled Keypad
enable/disable keypad button scrambling (random button
transposing) before every new display to prevent other persons from watching
the code entered (Enhanced Security license required). · Language set the
language for the texts to be displayed. Choose one of the predefined
languages: English, Czech, German, Italian, French, Spanish, Russian, Finnish,
Danish, Polish, Dutch, Portuguese, Turkish, Norwegian, Swedish, Thai, Hebrew
or a custom language. · Prefer Icons to Text the icons on the display will
be preferred to the text. · Power Saving Mode activate the power saving mode
in which the display brightness is reduced. If no event occurs during two
Slideshow screen activation timeouts, the power saving mode activation has
been successful. Set 0 in the Slideshow screen activation timeout to disable
the power saving mode. Any movement in front of the intercom camera or any
display event (such as door lock activation or display touch) restores the
full brightness of the display. · Showcase Mode set whether the device shall
go into the showcase mode when idle. Choose various options in the showcase
mode (OFF, Slideshow). · Delay of Showcase Mode Activation set the idle
timeout in the range of 1 to 600 seconds after which the device goes into the
Showcase Mode. There is always a fixed 15second timeout for the device to
return to the homescreen.
· Original Language download the localization file template for own
translation. It is an XML file with all the texts to be displayed.
· Custom Language remove, download and upload a localization file of your
own.
If none of the pre-defined languages is convenient for you, proceed as
follows: · Download the original language file (English). · Modify the file
using a text editor (replace the English texts with your own ones). · Upload
the modified localization file to the intercom. · Set Language Settings |
Language to Custom. · Check and correct if necessary the texts on the intercom
display.
99 / 283
Configuration manual for 2N IP intercoms Directory (for 2N® IP Verso and 2N® IP Vario)
This tab helps you configure a structured user list to be displayed. Create any count of groups and add any count of phonebook users to groups. No user can be assigned more times to a group, but one user can be added to multiple groups at the same time.
The created folders and users are displayed to the left. Click
to add a folder. Click to
remove a directory including users and groups. Click user from the main tree to a folder.
to rename a group. Click to move a
100 / 283
Configuration manual for 2N IP intercoms
The users assigned to the selected group are displayed to the right. Click
to add a user to
the group; yet the user remains in the phonebook main tree. Click to remove a user.
The groups and users are arranged in the alphabetical order on the display.
Click to assign a
priority. The directory items have 8 possible priorities. Priority 1 places
the item on the top of the list. No priority puts it on the end of the list.
Multiple items with identical priorities, if any, are grouped and arranged
alphabetically.
Caution · Remember to save the phonebook changes.
Slideshow for 2N® IP Verso
This tab helps you set the image and video list for the Slideshow mode. Up to
8 images and videos can be uploaded for the Slideshow to be switched with a
predefined delay.
· Slideshow Transition Time set the image transition time in a Slideshow. ·
Time Profile choose one or more time profiles to be applied. Set the time
profiles in
Directory / Time profiles.
·
select one of the pre-defined profiles or set the time profile for the given
element manually.
101 / 283
Configuration manual for 2N IP intercoms
Make sure that the image / video resolution is 214 x 214 or 214 x 320 pixels up to 2 MB. Other sizes will be adjusted to the display resolution automatically.
Click the magnifier icon
to view the uploaded image, press
to delete an image and
click
to hide a selected image/video on the device display. Click the variable image/video
icon
to set a time profile
for the display. If no time profile is active, the slideshow will
have no time profile conditioned content. In the same case, the slideshow will always have a
content that is not conditioned by a time profile.
If no image is uploaded, the Slideshow mode will never be activated.
Tip
· To hide the “Start with touch” display on the 2N® IP Verso model display,
upload an image of the resolution of 214 x 320 pixels.
Caution
· Video with a 214 x 320 resolution cannot be uploaded in FW versions lower
than 2.35.
Slideshow for 2N® IP Vario
This tab helps you configure a list of images for the Slideshow mode. Up to 8
images can be uploaded for the Slideshow to be switched with a predefined
delay.
102 / 283
Configuration manual for 2N IP intercoms
· Slideshow Transition Time set the image transition time in a slideshow.
Make sure that the image resolution is 320 x 240 pixels for 2N® IP Vario. Other sizes will be adjusted to the display resolution automatically.
Click the magnifier icon
to view the uploaded image, press
click
to hide a selected image/video on the device display.
If no image is uploaded, the Slideshow mode will never be activated.
to delete an image and
Caution · 2N® IP Vario only supports image display.
103 / 283
5.3.7.1 2N® IP Style Display
Configuration manual for 2N IP intercoms
The 2N® IP Style IP intercom is equipped with a 10 color LCD display with a
resolution of 800 x 1280. The display shows the device state (e.g. call
progress, door opening) and can work in several modes:
· Display display the directory including the users to be called and a
numeric keypad for code access.
· Directory display the configurable list of users, which can be browsed by
a finger touch on the display. You can create practically any count of groups
that can be mutually nested. You can assign any count of directory users to
each group.
· Slideshow a slideshow of recorded images can be displayed after a preset
idle time. The images are automatically switched over and the transition time
can be set.
· Logo a logo uploaded to the device configuration can be displayed after a
preset idle time.
· Address a house address / number / identifier can be displayed after a
preset idle time. · Date and Time set the date, time and weather parameters.
· Welcome Message set a message to be displayed after successful
authentication.
104 / 283
Display
Configuration manual for 2N IP intercoms
· Code Entering Keypad Button turn on the keypad display for entering
numeric codes. · Code Entering Keypad Mode set the keypad mode on the
display for entering numeric
codes. The modes include normal keypad and keypad with scrambled keys for
enhanced security. The setting is applied to the keypad even during multi-
factor authentication. · Door Control via PIN Code enables or disables door
control by entering a PIN code from the screen. · Credentials Forward Group
set the group to which all entered access codes will be forwarded. ·
Transmitted Code Format selects a 4bit or 8bit (higher security) format for
the codes to be transmitted
105 / 283
Configuration manual for 2N IP intercoms
· Language set the language for the texts to be displayed. Choose one of the
predefined languages: English, Czech, German, Italian, French, Spanish,
Russian, Finnish, Danish, Polish, Dutch, Portuguese, Turkish, Norwegian,
Swedish, Thai, Hebrew or a custom language.
· Root Folder Display select the type of directory root folder display on
the device home page. Choose Cards (larger image) or classic item list (the
item list image display then obeys the Show images setting. The setting will
take effect only once any user navigates to other part of GUI (e.g. Search).
· Directory Image Display choose whether or not the images in the directory
display shall be shown in the item list display.
· Touch Sounds enable the acoustic display touch signaling. · Showcase Mode
set whether the device shall go into the Showcase mode when idle.
Choose various options in the Showcase mode (OFF, Slideshow, Logo, Address,
Date and Time). · Showcase Mode Delay set the idle timeout in the range of 1
to 600 seconds after which the device goes into the Showcase mode.
106 / 283
Configuration manual for 2N IP intercoms
Caution · The device automatically returns to the display home page in a
60-second idle time. After that, the countdown of the timeout set in this
parameter starts and then the device goes into the Showcase mode. · After a
2-minute idle time, the screen saver is launched on 2N® IP Style, in which the
display brightness value goes up and down alternately in 20-second intervals.
The screen saver mode is terminated by a screen touch, access attempt,
incoming call, notification display or motion detection even in case the
motion detection function is disabled. If the screen saver is running on the
background in the Showcase mode, the termination by a touch also switches the
device onto the home page.
· Display Touch Icon in Showcase Mode Enable displaying of the touch icon
(pulsating hand) in the Showcase mode.
· Display Antibacterial Notification enable displaying of information on the
antibacterial layer applied to the display (2N® IP Style optional accessory)
during the Showcase mode.
· Bluetooth Authentication Button Mode sets whether the Bluetooth
authentication is activated by swipe or just tap. The setting will take effect
only once there are no phones with Mobile Key application in the vicinity of
2N® IP Style. · Swipe swipe the button from left to right to activate the
lock. · Tap tap the button to activate the lock.
· Bluetooth Button Location set the Bluetooth authentication button
location. The setting will take effect only once there are no phones with
Mobile Key application in the vicinity of 2N® IP Style.
· Background Image load the background image (to be used for various
screens). The file must be an image with the minimum resolution of 800 x 1280
pixels. Images with higher resolutions will be reduced in size.
107 / 283
Configuration manual for 2N IP intercoms
Caution · The root folder display changes are not applied until you go to the
search or dialing menu. · To apply the Bluetooth authentication button
location / mode display change, disconnect all the available devices with
Bluetooth authentication or move them outside the reach of 2N® IP Style.
· Original Language download a preset XML file with all the texts to be
displayed. · User Language record, remove and load a localization file of
your own. Note
If none of the pre-defined languages is convenient for you, proceed as
follows: · Download the original language file (English). · Modify the file
using a text editor (replace the English texts with your own ones). · Upload
the modified localization file to the intercom. · Set Language Settings |
Language to Custom. · Check and correct, if necessary, the texts on the
intercom display.
Directory
108 / 283
Configuration manual for 2N IP intercoms
This tab helps you configure a structured user list to be displayed. Create
any count of groups and add any count of phonebook users to groups. No user
can be assigned more times to a group, but one user can be added to multiple
groups at the same time.
The created folders and users are displayed to the left. Click
to add a folder. Click
to
remove a directory including users and groups. Click to rename a group. Click to move a
user from the main tree to a folder.
The users assigned to the selected group are displayed to the right. Click
to add a user to
the group; yet the user remains in the phonebook main tree. Press in the group on the display. Click to remove a user.
to highlight the first item
The groups and users are arranged in the alphabetical order on the display.
Click to assign a
priority. The directory items have 8 possible priorities. Priority 1 places
the item on the top of the list. No priority puts it on the end of the list.
Multiple items with identical priorities, if any, are grouped and arranged
alphabetically.
Caution
· Remember to save the phonebook changes. · The setting (photos, root folder,
content) display changes are not applied until you
go to the search or dialing menu.
Slideshow
This tab helps you configure a list of images to be displayed in the Slideshow
mode. Up to 14 images and videos can be uploaded for the Slideshow to be
switched with a predefined delay.
· Slideshow Transition Time set the image displaying time in a slideshow. ·
Time Profile choose one or more time profiles to be applied. Set the time
profiles in
Directory / Time profiles.
·
select one of the pre-defined profiles or set the time profile for the given
element manually.
109 / 283
Configuration manual for 2N IP intercoms
The recommended resolution is 800 x 1280 px for images and 400 x 640 px for
video files in 2N® IP Style. The device automatically adjusts images with a
different resolution value.
Video files must have the maximum resolution of 400 x 640 px, maximum size of
7 MB and maximum framerate of 24 fps.
Click the magnifier icon
to view the loaded image, press
to delete an image and click
to hide a selected image/video on the device display. Click the variable image/video icon
to set a time profile
for the display. If no time profile is active, the slideshow will have
no time profile conditioned content. In the same case, the slideshow will always have a content
that is not conditioned by a time profile.If no image is loaded, the Slideshow mode will never be
activated.
Caution
· The Slideshow images are displayed only if this mode is allowed in the
Hardware / Display / Display menu.
Logo
This tab helps you upload a logo for the Showcase mode. Any image with a
resolution higher than 800 x 1280 pixels will be reduced. Smaller files remain
the same and will not cover the whole area. PNG images with transparent
backgrounds are also supported.
110 / 283
Configuration manual for 2N IP intercoms
Caution · The Logo image is displayed only if this mode is allowed in the
Hardware / Display / Display menu.
Address
Address helps you set the house address or any other identifier for the
Showcase mode, which will be displayed during the device idle time.
111 / 283
Configuration manual for 2N IP intercoms
· Number enter the house number or any other identification used in the
location. It is displayed in the Showcase mode if Address is selected.
· Address enter the building address/name shown in the Showcase mode if
Address is selected.
· Swap Address And Number change the address and number sequence. Caution
· The Address image is displayed only if this mode is allowed in the Hardware
/ Display / Display menu.
112 / 283
Configuration manual for 2N IP intercoms Date and Time
Helps you set the date, time and weather parameters.
· Date Format set the data format to be displayed. · Time Format set the
time format to be displayed. Weather · Show Weather display the current
weather info on the device. · Location set the device location for weather
forecast. If not completed, the
automatically selected location is used. · Location Shown set the location
to be shown on the display. If not completed, the
weather forecast location is displayed. · Temperature Units select the
temperature units to be displayed. The options are °C and
°F.
Welcome Message
113 / 283
Configuration manual for 2N IP intercoms
Custom Image
Text Message
Here set a message to be displayed after successul authentication. · Welcome Screen Mode select the type of the welcome message content. · Display Time set the welcome message displaying time. · Icon select one of the welcome text icons:
Info
Caution
No Entry
Left Arrow
Up Arrow
Right Arrow
114 / 283
Configuration manual for 2N IP intercoms
Left Turn Arrow
Down Arrow
Right Turn Arrow
· Message Heading set the welcome text heading. · Message Body set the
welcome text body. · Confirmation set whether or not the welcome text is
provided with an OK confirmation
button. · Upload Custom Image upload an image to be used as a welcome
message. Make sure
that the image resolution is 800 x 1280 px and the format is JPEG or PNG.
5.3.8 Card Reader
This menu is available in the 2N® IP Base, 2N® IP Vario and 2N® IP Force
models only. For 2N® IP Verso only the option to limit unsuccessful access
attempts is configured here. Other card reader options can be configured in
the Extenders menu. The card reader helps you control access to your building
effectively using contactless RFID cards. The supported card types depend on
the card reader model used.
115 / 283
Configuration manual for 2N IP intercoms
The 2N® IP Vario and 2N® IP Force card readers are equipped with an
input/output Wiegand interface. The interface direction is configurable. In
the input mode, the interface can be used for connection of external card
readers, fingerprint readers, biometric data readers and so on. In the output
mode, the interface helps connect the intercom to the security exchange, e.g.
and send IDs of the cards tapped on the internal reader to this exchange.
116 / 283
Basic Settings
Configuration manual for 2N IP intercoms
· Door set the reader direction (Arrival, Departure) for the Attendance
system purposes. · Associated Switch set the number of the switch to be
activated by tapping of a valid
RFID card. The set value is not applied when a valid user card is tapped on
the reader while the double authentication mode is enabled. In this case, a
numeric switch activating code is required to identify the switch to be
activated.)
RFID Interface
· Allowed Card Types select one or more card types to be accepted. If no
selection is made, all types of supported cards are accepted.
Wiegand Interface
117 / 283
Configuration manual for 2N IP intercoms
· Interface Mode enable the Wiegand function and set Wiegand IN/OUT. The IDs
of the cards tapped on the internal card reader are always resent to Wiegand
OUT.
· Door set the reader direction (Arrival, Departure) for the Attendance
system purposes. · Received Code Format set the format for the codes to be
received (Wiegand 26, 32, 37
and RAW). · Transmitted Code Format set the format for the codes to be
transmitted (Wiegand 26,
32, 37 and RAW). · Change Facility Code set the first code part via Wiegand.
This applies to Wiegand OUT
for 26-bit code format. Contact your security system supplier to know if the
Facility Code is requested. · Facility Code define the 2N IP intercom
location in the security system. Enter a decimal value for the location
(0255).
118 / 283
Configuration manual for 2N IP intercoms 5.3.9 Digital Inputs
In this configuration section set the parameters associated with digital
inputs and their interconnections with other intercom functions. The digital
inputs are available in selected intercom models or where appropriate
equipment is installed (e.g. card readers).
Door
· Assigned Switch select a switch for the electromagnetic door lock control.
The switch state controls the door unlocking signaling (green door symbol,
green LED).
119 / 283
Configuration manual for 2N IP intercoms
· Assigned Input define one (or none) of the logical inputs for open door
detection. · Unauthorized Door Open Detection detect if the door is open
when switch has been
locked. · Door Open Too Long Detection door open too long detection. ·
Maximum Door Open Time maximum permitted door open duration in seconds.
· Assigned Input select one (or none) of the logic inputs for the departure
button function. The departure button input activation activates the selected
switch. The activation time and mode are set by the selected switch
parameters.
· Input Mode set the active input mode (polarity).
Security
· Assigned input define one (or none) of the logical inputs for secured
state detection. The secured state is then signalled by a LED on the intercom,
whose location may vary in different intercom types.
· Input mode set the active input mode (polarity).
120 / 283
Configuration manual for 2N IP intercoms
Note · Secured state signalling is typically used with an access control
controller connected to one of the intercom digital inputs. The wire leading
from the PBX is connected to the intercom directly or via an extending module.
The secured state LED location is variable depending on the intercom type: The
2N® IP Vario (91371…U) intercoms are equipped with a red LED indicator located
in the middle of the backlit name tags. The 2N® IP Force intercoms are
equipped with a red LED indicator located in the integrated card reader
window. The 2N® IP Verso intercoms are equipped with a red padlock pictogram
in the lefthand upper corner of the basic module.
The tamper switch equipped models help detect opening of the device cover and
signal this event as TamperSwitchActivated. The events are written into a log
and read out via HTTP API (refer to the HTTP API manual). If the function is
enabled, all the switches get blocked for 30 minutes whenever the tamper is
activated. Blocking is active even after the device restart. Each port can be
controlled via Automation. Press the UNBLOCK button, disable the function or
reset the configuration factory values to unblock the switches.
· Assigned input select the logical input to which the tamper switch is to
be connected. TamperSwitchActivated signals the tamper switch activation.
· Enable automatic switch blocking block the switches by tamper activation
for 30 minutes.
· Switch blocking state display and make switch blocking settings.
121 / 283
Triggers
Configuration manual for 2N IP intercoms
· User Actions Trigger 1, 2 · Assigned input select a logic input that will
fulfil the user action function. In case the function is activated, the
UserActionActivated event with parameter state=in (function deactivation is
indicated by state=out) is written into the device event log. Based on this
event, for example, superior systems can trigger alarm, lock the whole
building or perform any other action. · Input mode select whether a user
action should be evaluated based on the inverted or normal value of the
assigned input.
5.3.10 Extenders
The 2N® IP Verso and 2N® IP Style intercoms can be extended by means of
extending modules connected to the intercom basic unit via a VBUS. The
following modules are available:
· Five-button module · Keypad module · Infopanel module · Card reader module ·
Bluetooth module
122 / 283
Configuration manual for 2N IP intercoms
· I/O module · Wiegand module · OSDP module · Induction loop module · Display
module · Fingerprint reader · Touch keypad · Touch keypad & RFID reader 125
kHz, 13.56 MHz · Bluetooth & RFID reader 125 kHz, 13.56 MHz · Touch keypad &
Bluetooth & RFID reader 125 kHz, 13.56 MHz The modules are chain-like
interconnected. Each of the modules has its number depending on the chain
position (the first module has number 1). The basic unit is a special type of
module and has number 0. You can configure each module separately. The
parameters are specific for the given module type. Caution
· The connected module is not detected automatically. Restart the device to
see the module in the extender list.
· In case the firmware versions of the module to be connected and the main
unit are incompatible, the module will not be detected. Therefore, it is
necessary to update the device firmware after the modules are connected. Use
the device web interface in the System > Maintenance > System configuration
section for firmware upgrade.
Caution · Be sure to configure the replaced modules. The configuration is tied
with the module serial number.
123 / 283
Configuration manual for 2N IP intercoms
Note · The extending modules are displayed in the order corresponding to their
interconnection. The modules connected further from the basic unit are listed
below. If more modules of the same type are connected to one intercom, it may
be difficult to assign a setting to a particular module. In this case,
identify the modules connected using the Locate Module button. The module will
flash shortly several times when you press the button.
Caution · Having connected the card reader module via the VBUS cable to a
device into which the 2N® PICard reading keys have been uploaded, remember to
pair the module with the device. Without pairing, the card reader module will
not have access to the reading keys and be unable to read encrypted cards.
Click Pair Module to pair the module.
124 / 283
Configuration manual for 2N IP intercoms
Caution · Module Name has to be unique. · Unnameable modules can be addressed
via ext
Tip · Place the mouse cursor onto the module image to display the module’s
basic production and software information.
125 / 283
Main Unit Module Configuration
Configuration manual for 2N IP intercoms
· Locate Device optical and acoustic signaling of a device. Note: Optical signaling is possible only if the device is equipped with control backlight (Verso, Base, Vario, Force, Safety and Uni). If a speaker is not integrated in the device, make sure than an external speaker is connected (Audio Kit and Video Kit) to use sound signaling.
126 / 283
Button Module Configuration
Configuration manual for 2N IP intercoms
· Button Function assign user positions to the buttons.
Keypad Module Configuration
· Module Name set the module name for logging events from the keypad.
127 / 283
Configuration manual for 2N IP intercoms
· Door set the reader direction (Door Entry, Door Exit) for the Attendance
system purposes.
· Forward to Wiegand Output set a group of Wiegand outputs to which all
pressed keys are to be forwarded.
· Transmitted Code Format select a 4bit or 8bit (higher security) format for
the codes to be transmitted.
Infopanel Module Configuration
· No parameters are available to the public at present.
128 / 283
Configuration manual for 2N IP intercoms 125 kHz Card Reader Module
Configuration
· Module Name set the module name for card reader logging purposes. · Door
set the reader direction (Door Entry, Door Exit) for the Attendance system
purposes. · Associated Switch set the switch to be activated after user
authentication via this
module. If you set Door Lock Switch, the authentication rules specified in
Hardware / Door will be used. · Allowed Card Types set the type of a card to
be accepted by the card reader. The card reader supports just one card type at
an instant. · Forward to Wiegand Output set a group of Wiegand outputs to
which all the received RFID card IDs will be resent. Tip
· To accelerate card reading, you are recommended to select the card types
used by the user in the module settings.
129 / 283
Configuration manual for 2N IP intercoms 13.56 MHz Card Reader Module
Configuration
· Module Name set the module name for card reader logging purposes. · Door
set the reader direction (Door Entry, Door Exit) for the Attendance system
purposes. · Associated Switch set the switch to be activated after user
authentication via this
module. If you set Door Lock Switch, the authentication rules specified in
Hardware / Door will be used. · Allowed Card Types set the type of a card to
be accepted by the card reader. The card reader supports just one card type at
an instant. · Samsung NFC Compatibility enable NFC compatibility with the
Samsung phones. · Forward to Wiegand Output set a group of Wiegand outputs
to which all the received RFID card IDs will be resent. Tip
· To accelerate card reading, you are recommended to select the card types
used by the user in the module settings.
130 / 283
Bluetooth Module Configuration
Configuration manual for 2N IP intercoms
· Module Name set the module name for logging events from the Bluetooth
module. · Door set the reader direction (Not specified, Arrival, Departure)
for the Attendance
system purposes. · Associated Switch set the switch to be activated after
user authentication via this
module. If you set Door Lock Switch, the authentication rules specified in
Hardware / Door will be used. · Signal Range set the signal range (5 =
maximum, 1 = minimum), i.e. the distance over which the Bluetooth module can
communicate with a mobile phone. It is recommended that the actual signal
range is tested while setting, as it is affected by a number of factors
(installation layout, mobile phone type and position in particular). · Launch
Authentication by set the authentication method for a mobile phone:
· Tap in app authentication has to be confirmed by tapping on an icon in the
application running in a mobile phone.
· Interacting with Device touch the card reader having a phone with paired
2N® Mobile Key to confirm authentication.
· Motion detection authentication will be launched by motion detection via a
phone with the paired 2N® Mobile Key application.
· Motion Detection Profile set the motion detection profile for the module
authentication via a mobile phone.
131 / 283
I/O Module Configuration
Configuration manual for 2N IP intercoms
· Module Name set the module name for input/output specification in the SetOutput, GetInput and InputChanged objects in Automation.
132 / 283
Configuration manual for 2N IP intercoms Wiegand Module Configuration
The Wiegand module is equipped with the input and output Wiegand interfaces,
which are mutually independent, have separate settings and can receive and
send codes at the same time. The Wiegand input helps you connect such
equipment as RFID card readers, biometric readers and so on. With the Wiegand
output, you can connect the intercom to the security system in your building,
for example (to send IDs of the RFID cards tapped on the RFID reader or codes
received on any Wiegand input). The 2N® Wiegand Isolator is also equipped with
one logical input and one logical output, which can be controlled via
Automation.
· Module Name set the module name for input/output specification in the
SetOutput, GetInput and InputChanged objects in the 2N Automation.
· Door set the reader direction (Arrival, Departure) for the Attendance
system purposes. · Associated Switch set the switch to be activated after
user authentication via this
module. If you set Door Lock Switch, the authentication rules specified in
Hardware / Door will be used. · Received Code Format set the format for the
codes to be received (Wiegand 26, 32, 37 and RAW). · Output Wiegand Group
assign the output Wiegand to a group to which the codes from the connected
card readers or Wiegand inputs can be resent.
133 / 283
Configuration manual for 2N IP intercoms
· Transmitted Code Format set the format for the codes to be transmitted
(26-bit, 32-bit, 37-bit and RAW format, 35-bit, Corp. 1000, 48-bit, Corp. 1000
and Auto).
· Change Facility Code set the first code part via Wiegand. This applies to
Wiegand OUT for 26-bit code format. Contact your security system supplier to
know if the Facility Code is requested.
· Facility Code define the 2N IP device location in the security system.
Enter a decimal value for the location (0255).
134 / 283
Configuration manual for 2N IP intercoms OSDP Module Configuration
The OSDP module is equipped with an (input-output) OSDP (RS-485) interface.
OSDP helps you connect the 2N IP intercom to, e.g., a building security system
or Control Panel (to send the RFID card IDs read on the connected RFID reader
or PIN codes).
· Module Name set the module name. The module name is used for input /
output specification in Automation.
· Credentials Forward Group assign the OSDP output to the group to which
codes from the connected card readers or OSDP inputs can be resent.
· Transmitted Code Format set the code format to be transmitted. · OSDP
Address OSDP module address ranging from 0 to 126 on an OSDP line. ·
Baudrate set the communication rate in compliance with the device connected.
· Encryption Key set your own key for encrypted communication. · Mode use
the installation mode for encryption key remote setting on the peripheral if
enabled. Once the encryption key is received, the normal operation is switched
on automatically. The installation mode is signaled by a fast flashing of the
LED indicator on the OSDP module. · Force Encryption set forced encryption
for encrypted communication only.
135 / 283
Configuration manual for 2N IP intercoms
Caution · When communication is made by the OSDP device in an unencrypted
format after forced encryption is set, this communication will be rejected.
Induction Loop Module Configuration
· Module Name set the module name. The module name is used for induction
loop event logging.
· Maximum Power set the maximum transmission power for the induction loop
antenna. A higher transmission power means a wider range, but less power for
other intercom functions. The convenient default value is 0.25 W under normal
circumstances.
136 / 283
Display Module Configuration
Configuration manual for 2N IP intercoms
· Module Name set the module name for logging the display events. · Door
set the reader direction (Door Entry, Door Exit) for the Attendance system
purposes. · Credentials Forward Group set the group to which all the
received user access codes
will be resent. · Transmitted Code Format select a 4bit or 8bit (higher
security) format for the codes to
be transmitted.
137 / 283
Configuration manual for 2N IP intercoms Fingerprint Reader Module
Configuration
· Module Name set the module name for logging events from the Fingerprint
reader. · Door set the reader direction (Arrival, Departure) for the
Attendance system purposes. · Associated Switch set the switch to be
activated after user authentication via this
module. If you set Door Lock Switch, the authentication rules specified in
Hardware / Door will be used. · Sunlight Sensivity Mode enable this
parameter to prevent erroneous behavior of the reader if exposed to direct
sunlight. Restart the device to change the setting. The mode may reduce the
reading sensitivity. Caution
· Whenever the fingerprint reader is disconnected, the User fingerprints will
be hidden in the user profile after restart. This section displays how many
user fingerprints have been uploaded to the intercom memory. Once a
fingerprint reader is reconnected, the User fingerprints will be displayed
again.
138 / 283
Touch Keypad Configuration
Configuration manual for 2N IP intercoms
· Module Name set the module name for logging events from the touch keypad.
· Door set the reader direction (Door Entry, Door Exit) for the Attendance
system
purposes. · Blink at Keystroke set keystroke light signaling for noisy
environments
References
- 2N - a Global Leader in IP Intercoms and Access Control - 2N
- yourcompany.com is available for purchase - Sedo.com
- yourcompany.com is available for purchase - Sedo.com
- FAQ Dashboard
- FAQ Dashboard
- 2N - a Global Leader in IP Intercoms and Access Control - 2N
- 2N - a Global Leader in IP Intercoms and Access Control - 2N
- 2N - a Global Leader in IP Intercoms and Access Control - 2N
- Wireshark · Go Deep
- Wireshark · Go Deep
- 2N Manuals Dashboard
- FAQ Dashboard
- FAQ Dashboard
- FAQ Dashboard
- FAQ Dashboard
- FAQ Dashboard
- FAQ Dashboard
- Audacity - Interoperability Manual
- 2N - Jednička v oblasti IP interkomů a kontroly přístupu - 2N
- AXIS IP Utility | Axis Communications
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>