ideal lux SP7 Giada Pendant Light Suspension Lamp Instruction Manual
- June 1, 2024
- ideal lux
Table of Contents
ideal lux SP7 Giada Pendant Light Suspension Lamp
Product Information
Specifications:
- Brand: Giada
- Model: SP7 G9
- Max Power: 7 x 40W
- Power Supply: 220-240V, 50/60Hz
- Product Code: 8021696098739
- Energy Efficiency Class: F
Product Usage Instructions
Installation:
The lighting fitting should be installed by a qualified electrician. Follow
the assembly instructions by reading the numerical progression provided in the
manual.
Light Source Replacement:
This product is equipped with a light source that can be replaced by the
end-user. Refer to the legend icons for guidance on the type of light sources
that can be replaced.
Safety Instructions:
- Ensure the device complies with European safety standards EN 60 598-1.
- For some regulations, installation must be carried out by a qualified electrician.
- If the external power cable is damaged, it should only be replaced by the manufacturer, retailer, or a qualified electrician.
- Always disconnect the power supply before starting any installation or maintenance work.
- Use appropriate fixing accessories for different materials and ensure compliance with regulations.
- Do not disassemble the LED light source; it is non-replaceable.
- If the lamp fails to turn on, replace the fuse if applicable.
- The device is equipped with a fuse for added safety.
Frequently Asked Questions (FAQ):
-
Q: Can I replace the LED light source myself?
A: No, the LED light source is not user-replaceable. It should only be replaced by authorized personnel. -
Q: What should I do if the lamp does not turn on?
A: Check the fuse and replace it if necessary. If the issue persists, contact the manufacturer or retailer for further assistance. -
Q: Is it safe to install the lighting fitting without a qualified electrician?
A: It is recommended to have the lighting fitting installed by a qualified electrician to ensure safety and proper functionality.
SAFETY INSTRUCTIONS
- This fitting is produced and tested by the strictest European safety standards (EN 60.598-1).
- This fitting cannot be disposed of as household waste. For disposal information ask the local authorities about how to collect it.
- As indicated by specific regulations, the lighting fitting should be installed by a qualified electrician.
- If the external wire is damaged it has to be replaced exclusively by the manufacturer, distributor or by a qualified electrician.
- Always isolate power before commencing installation, maintenance or repair.
- The luminaire contains certain parts which can be very hot.
- Each material requires specific mounting accessories. Use screws and wall plugs suitable for the material to which they are fastened. Those included may be unsuitable.
- Always tighten the screws firmly to avoid contact problems.
- This fitting should only be installed indoors.
- Luminaires are not suitable for recessed on normally flammable surfaces.
- Luminaire is not suitable for direct mounting on normal flammable surfaces.
- This fitting is only suitable for fixing to the ceiling.
- This fitting is only suitable for fixing to the wall.
- The weight of the lamp has to be supported by the chain. Adjust the length of the electric wire so that it is longer than the chain.
- Only use lamps that do not exceed the maximum specified wattage.
- Always observe the minimum distance between the lamp and the surface being lit, as shown in the icon. The lamp can cause a fire if the minimum distance is not observed.
- Auto-protected bulb. Only use bulbs marked with this symbol. Halogen bulbs get very hot. Wait until they cool down before replacing them.
- Cracked or broken safety glass has to be replaced immediately. Use only manufacturer-approved parts complying with regulations.
- Light source with not-substitutable light emitting diode (LED). Do not disassemble the products the diodes can damage the eyes. Do not immerse in water. Wipe with a damp cloth. Do not use solvents or strong detergents.
- This fitting is equipped with a fuse. If the lamp is out of order, replace the internal fuse.
- Class I Electrical safety is guaranteed by the main insulation and an additional protective conductor (earthing) connected with the metal frame of the lamp. Earthing is obligatory.
- Class I| Electrical safety guaranteed by the main insulation and double or reinforced insulation. Earthing not necessary.
- Class III Electrical safety is guaranteed by very low power supply (less than 50 Volt). Earthing excluded.
- Not protected.
- Protected against solid objects greater than 50 mm.
- Protected against solid objects greater than 12 mm.
- Protected against solid objects greater than 2,5 mm.
- Protected against solid objects greater than 1mm.
- Dust protected.
- Protected against dust infiltration.
- Not protected.
- Protected against vertically falling water drops.
- Protected against water drops falling with a maximum angle of 15° to the vertical axis.
- Protected against rain.
- Protected against splashing water.
- Protected against water jets.
- Protected against strong water jets.
- Protected against temporary immersion.
- Protected against prolonged immersion.
- Luminaire was not suitable for covering with thermally insulating material.
- Caution, risk of electric shock.
- Do not stare at the operating light source.
FEATURES
- Suspension lamp
- G9 max 7 x 40W / 220~240V 50/60Hz
- 8021696098739 TRASPARENTE
DIMENSION
This product is provided with a light source with efficient energy class of:
- EAN/Energy Efficiency Class
- 8021696209043 F
ASSEMBLY INSTRUCTIONS
- FOLLOW THE ASSEMBLY INSTRUCTIONS BY READING THE NUMERICAL PROGRESSION
- THE LIGHTING FITTING SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN
THE SAFETY AND RELIABILITY ARE GUARANTEED ONLY WHEN INSTALLATION INSTRUCTIONS ARE PROPERLY FOLLOWED. PLEASE KEEP THIS INSTRUCTION SHEET FOR FUTURE REFERENCE.
LEGENDA ICONE
- Replaceable light source by an end-user.
- Replaceable LED light source by an end-user.
- Replaceable light source authorized personnel only.
- Non-replaceable light source.
- Upon end of life of the light source, the whole product will be replaced.
- Replaceable control gear by an end-user.
- Replaceable light source by authorized personnel only.
- Upon end of life of the control gear, the whole product will be replaced.
IDEAL LUX s.r.l.
Via Taglio Destro 32
30035 Mirano (VE) Italy
www.ideal-lux.com
IDEAL LUX Warehouse Via delle Industrie, 8/D
30036 Santa Maria di Sala (Venezia) 8.00 – 12.00 / 13.30 – 17.00
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>