Panasonic PT-DX100 Fixed Installation Projector Instructions

Panasonic PT-DX100 Fixed Installation Projector

Product Information

Specifications

• Model: PT-DX100
• Projection System: 1-Chip DLP
• Lumens: 10000
• Resolution: XGA (1024 x 768 pixels)
• Lamps: 2 x 420 W UHM lamps
• Lens: Exchangeable lens system with various options
• Contrast Ratio: 10,000:1

Product Usage Instructions

• Installation
  The projector can be installed on the ceiling or floor for front or rear projection.

• Lens Installation
  If using the PT-DX100K/DX100W lens, adjust the zoom and focus as needed. For the PT-DX100LK/DX100LW lens options, follow the specific instructions provided with the lens.

• Powering On/Off
  Connect the projector to a power source and press the power button to turn it on. Use the remote control or buttons on the projector to power off.

• Input Connections
  For video input, connect devices to the available terminals such as DVI-D In or RGB 1 In based on the signal type.

• Adjusting Settings
  Use the menu options on the projector to adjust settings like brightness, contrast, keystone correction, and colour settings for optimal image quality.

• Maintenance
  Regularly clean the air filters and replace them as needed. Monitor lamp usage and replace when necessary for continued performance.

Frequently Asked Questions

• Q: How do I change the lamp on the PT-DX100 projector?
  A: To change the lamp, first power off the projector and allow it to cool. Remove the lamp cover, unscrew the lamp module, and replace it with a new one following the manufacturer’s instructions.

• Q: Can I use third-party lenses with the PT-DX100 projector?
  A: It is recommended to use compatible lenses provided by the manufacturer to ensure proper fit and performance.

• Q: What is the recommended screen size for optimal viewing?
  A: The PT-DX100 projector supports screen sizes ranging from 50 to 600 inches, ensuring flexibility in various installation environments.

1DLP – 10000 lumens – XGA – 2Lamps – Exchangeable lens – Dynamic RGB Booster – Digital Link

PT-DX100
10000 lumens-class fixed installation projector Delivering stunning colours and highly flexible projection for museums, exhibitions and digital signage applications

Key Features

• 1-Chip DLP, 10000 lumens, XGA
• Excellent image quality thanks to the dynamic RGB Booster and Vivid Colour Control
• A dual lamp system with lamp relay mode enables 24/7 operation
• Eco filter enables up to 12000 hours of air filter replacement cycle
• 10,000:1 contrast ratio

Specification

• Power Consumption (120-240V AC, 50/60Hz)
  1,030 W(1,060 VA) (0.3 W with STANDBY MODE set to ECO, 3 W with STANDBY MODE set to NORMAL)

• DLP™ Chip Panel Size
  17.8 mm (0.7 in) diagonal (4:3 aspect ratio)

• Lens PT-DX100K/DX100W
  Powered zoom/focus lenses (1.8 – 2.5:1), F 1.7 – 1.9, f 25.6 – 35.7 mm

• Lens PT-DX100LK/DX100LW
  Optional powered zoom/focus lenses and fixed-focus lens

• Lamp
  420 W UHM lamps (x 2)

• Screen Size
  1.27-15.24 m (50-600 inches), 1.27-5.08 m (50-200 inches) with the ET-DLE055 (4:3 aspect ratio), 2.54-8.89 m (100-350 inches) with the ET-DLE030 (4:3 aspect ratio)

• Brightness
  10,000 lumens (dual lamp, LAMP MODE: NORMAL)

• Center-to-Corner Uniformity
  90%

• Contrast
  10,000:1 (full on/full off, in dynamic iris 3 mode)

• Resolution
  1,024 x 768 pixels (Input signals that exceed this resolution will be converted to 1,024 x 768 pixels.)

• Scanning Frequency (HDMI/DVI-D)
  fH: 15 – 100 kHz, fV: 24 – 120 Hz, dot clock: 25 – 162 MHz

• Scanning Frequency (RGB)
  fH: 15 – 100 kHz, fV: 24 – 120 Hz, dot clock: 162 MHz or lower

• Scanning Frequency YPBPR (YCBCR)
  525i(480i): fH 15.75 kHz; fV 60 Hz, 625i(576i): fH 15.63 kHz; fV 50 Hz,525p(480p): fH31.50 kHz; fV 60 Hz, 625p(576p): fH 31.25 kHz; fV 50 Hz, 750(720)/60p: fH 45.00 kHz; fV60 Hz, 750(720)/50p: fH 37.50 kHz; fV 50 Hz, 1125(1035)/60i: fH 33.75 kHz; fV 60 Hz,1125(1080)/60i: fH 33.75 kHz; fV 60 Hz, 1125(1080)/50i: fH 28.13 kHz; fV 50 Hz,1125(1080)/25p: fH 28.13 kHz; fV 25 Hz, 1125(1080)/24p: fH 27.00 kHz; fV 24 Hz,1125(1080)/24sF: fH 27.00 kHz; fV 48 Hz, 1125(1080)/30p: fH 33.75 kHz; fV 30 Hz,1125(1080)/60p: fH 67.50 kHz; fV 60 Hz, 1125(1080)/50p: fH 56.25 kHz; fV 50 Hz

• Scanning Frequency (Video/S-Video)
  fH: 15.75 kHz, fV: 60 Hz [NTSC/NTSC4.43/PALM/PAL60]; fH: 15.63 kHz, fV: 50 Hz [PAL/PAL-N/SECAM]

• Optical Axis Shift
  Vertical: +50% (powered) (±45° with the ET-DLE085/ET-DLE105), Horizontal: ±10%(powered); NOTE: Optical axis shift function cannot be operated when used with the ET-DLE055. If using the ET-DLE030, the optical axis is fi xed.

• Keystone Correction Range
  Vertical ±40°; ±30° with the ET-DLE055/ET-DLE085/ET-DLE105. Cannot be used when theET-DLE030 is installed.

• Installation
  Ceiling/floor, front/rear

• Terminals DVI-D In
  DVI-D 24-pin x 1, DVI 1.0 compliant, HDCP compatible, for single link only; 525i(480i),625i(576i), 525p(480p), 625p(576p), 750(720)/60p, 750(720)/50p, 1125(1080)/60i,1125(1080)/50i, 1125(1080)/25p, 1125(1080)/24p, 1125(1080)/24sF, 1125(1080)/30p,1125(1080)/60p, 1125(1080)/50p; VGA(640 x 480) – WUXGA(1,920 x 1,200), dot clock: 25MHz – 162 MHz; NOTE: Compatible with non- interlaced signals only.

• Terminals RGB 1 In
  BNC x 5

• Terminals RGB 1 In R, G, B
  R: 0.7 Vp-p, 75 ohms; G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms; B: 0.7 Vp-p, 75ohms; HD, VD/SYNC: TTL, high impedance, positive/negative automatic; NOTE: SYNC/HDand VD terminals do not accept tri-level sync signals.

• Terminals RGB 1 In Y, PB, PR (Y, CB, CR)
  Y: 1.0 Vp-p (including sync signal), PB/PR (CB/CR): 0.7 Vp-p, 75 ohms

• Terminals RGB 1 In S-Video Signal
  Y: 1.0 Vp-p, C: 0.286 Vp-p, 75 ohms

• Terminals RGB 2 In
  D-sub HD 15-pin (female) x 1

• Terminals RGB 2 In R, G, B
  R: 0.7 Vp-p, 75 ohms; G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms; B: 0.7 Vp-p, 75ohms; HD, VD/SYNC: TTL, high impedance, positive/negative automatic; NOTE: SYNC/HDand VD terminals do not accept tri-level sync signals.

• Terminals RGB 2 In Y, PB, PR (Y, CB, CR)
  Y: 1.0 Vp-p (including sync signal), PB/PR (CB/CR): 0.7 Vp-p, 75 ohms

• Terminals 3D Sync 1 In/Out
  BNC x 1, 1.0 Vp-p, 75 ohms; Input: TTL, high impedance. Output: TTL, max. 10 mA

• Terminals 3D Sync 2 Out
  BNC x 1, 1.0 Vp-p, 75 ohms, TTL, max. 10 mA

• Terminals Video In
  BNC x 1, 1.0 Vp-p, 75 ohms

• Terminals Serial In
  D-sub 9-pin (female)x 1 for external control (RS-232C compliant)

• Terminals Serial Out
  D-sub 9-pin (male) x 1 for link control (RS-232C compliant)

• Terminals Remoter 1 In
  M3 jack x 1 for wired remote control

• Terminals Remoter 1 Out
  M3 jack x 1 for link control

• Terminals Remoter 2 In
  D-sub 9-pin (female)x 1 for external control (parallel)

• Terminals LAN/DIGITAL LINK
  RJ-45 x 1 for network and DIGITAL LINK (video/network/serial control) connection,100Base-TX, compatible with Art-Net, compliant with PJLink™ (class 1), Deep Color, compatible with HDCP, 525i(480i), 625i(576i), 525p(480p), 625p(576p), 750(720)/60p,750(720)50p, 1125(1080)/60i, 1125(1080)/50i, 1125(1080)/25p, 1125(1080)/24p,1125(1080)/24sF, 1125(1080)/30p, 1125(1080)/60p, 1125(1080)/50p; VGA(640 x 480) -WUXGA(1,920 x 1,200), dot clock: 25 MHz – 162 MHz; NOTE: Compatible with non-interlaced signals only.

• Power Cord Length
  3.0 m (9 ft 10 in)

• Cabinet Materials
  Molded plastic

• Dimensions (W x H x D) PT-DX100K /DX100W
  498 x 200 x 556 mm (19-19/32 x 7-7/8 x 21-7/8 inches) (with supplied lens)”

• Dimensions (W x H x D) PT-DX100LK /DX100LW
  498 x 200 x 513 mm (19-19/32 x 7-7/8 x 20-3/16 inches) (without lens)”

• Weight PT-DX100K/DX100W
  Approx. 18.3 kg (40.3 lbs) (with supplied lens)

• Weight PT-DX100LK/DX100LW
  Approx. 17.6 kg (38.8 lbs) (without lens)

• Operation Noise
  40 dB (dual lamp operation, LAMP MODE: NORMAL), 35 dB (dual lamp operation, LAMPMODE: ECO)

• Technology
  1-Chip DLP

• Power Supply
  120-240 V AC, 10-5.2 A, 50/60 Hz

• DLP™ Chip Display Method
  DLP™ chip x 1, DLP™ system

• DLP™ Chip Pixels
  786,432 (1,024 x 768) x 1, total of 786,432 pixels

• Terminals HDMI In
  HDMI 19-pin x 1, Deep Color, compatible with HDCP, 525i(480i), 625i(576i), 525p(480p),625p(576p), 750(720)/60p, 750(720)/50p, 1125(1080)/60i, 1125(1080)/50i,1125(1080)/25p, 1125(1080)/24p, 1125(1080)/24sF, 1125(1080)/30p, 1125(1080)/60p,1125(1080)/50p; VGA(640 x 480) – WUXGA(1,920 x 1,200), dot clock: 25 MHz – 162 MHz;NOTE: Compatible with non-interlaced signals only.

• Operating Temperature
  0℃ – 45 ℃ (32℉ – 113℉)

• Operating Humidity
  10% – 80% (no condensation)

Note
Weights and dimensions shown are approximate. Specifications and appearance are subject to change without notice.

1. When the STANDBY MODE is set to ECO, network functions such as power on over the network will not operate, and the serial output terminal cannot be used. Also, only certain commands can be received for external control using the serial terminal.
2. Measurement, measuring conditions, and method of notation all comply with ISO21118 international standards.
3. Only compatible with a dot clock frequency of 27 MHz (pixel repetition signal)
4. WUXGA resolution is supported only when the signals are compliant with VESA CVT-RB(Coordinated Video Timing-Reduced Blanking).
5. With legs at the shortest position.
6. Average value. May differ depending on models.
7. The operating temperature range is 0 °C to 40 °C (32 °F to 104 °F) when the fan control is set to High Altitude mode (for altitudes from 1,400 m to 2,700 m (4,593 ft to 8,858 ft)above sea level). Also, if the ambient temperature exceeds 40 °C (104 °F) (35 °C (95 °F) in high Altitude mode) when the projector is being used with Lamp Select set to Dual andLamp Power set to High, the light output may be reduced approximately 20% to protect the projector.
8. Operation range differs depending on the environment.

PT-DX100
https://eu.connect.panasonic.com/es/en/products/projectors/pt-dx100.

References

• Panasonic Connect Europe - CHANGE WORK, ADVANCE SOCIETY, CONNECT TO TOMORROW.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>