sikkerthjem S7 Pro Smart Pad Touch panel Med User Guide

sikkerthjem S7 Pro Smart Pad Touch panel Med

Specifications

• Working humidity : 90%
• Working temperature: -10~50
• Input: DC 5V 1.5A
• Battery: Lithium-ion 800 mAH
• Frequency: 433.92 MHz / 868.35 MHz
• Transmission distance: Up to 1000m without obstacles
• Standby time: 180g with backup battery
• Switch: Reset button
• Buttons: 13 touch buttons
• Materials: [Materials]

Product Usage Instructions

Paring the Keyboard with the Main Panel:

1. Ensure the keyboard is properly paired with the system.
2. Scan the QR code for pairing.

Activating the Panel:
To activate the panel:

• Press the activation button on the keyboard.
• Choose between activate, deactivate, or home activation modes.

Troubleshooting:
If you encounter any issues such as low battery, unresponsiveness from the keyboard, difficulty in pairing, or inability to deactivate using the RFID tag, follow these steps:

• Check the battery status and replace if necessary.
• Reset the keyboard by pressing the reset button.
• Ensure proper pairing between the keyboard and system.
• If unable to deactivate with the RFID tag, ensure it is paired correctly with the system.

FAQ

• Why is my keyboard not responding?
  If your keyboard is not responding, check for any interference or try replacing the battery.

• How do I pair the RFID tag with the system?
  To pair the RFID tag with the system, ensure it is correctly scanned and paired using the provided QR code.

• What should I do if I cannot deactivate the system using the RFID tag?
  If you cannot deactivate the system using the RFID tag, verify that the tag is properly connected and paired with the system.

Introduction

Foreword

• Thank you for purchasing this wireless keypad. It is recommended to install close to the entry door inside, so users can conveniently operate arm, disarm, home arm after inputting passcode on keypad or arm/disarm by the RFID tags.
• This keypad is recommended to use the Entry Delay feature of the smart alarm system, to avoid triggering alarm before disarming from keypad after entering the house.
• The operations are quite easy, just input the passcode then press [Arm]/[Disarm]/[Home Arm] key, or put RFID tag on the keypad to arm/disarm the system.

Parts List

Care & Maintenance

Usage Notices

• The keypad should be paired to control panel before use.
• The power supply of keypad could impact on the transmitting distance of wireless signal.
• The keypad is compatible for most of our alarm system, contact the distributer for more detail.
• Please make sure the battery has been installed in the keypad before use.
• The keypad is neither waterproof nor moisture-proof, please install it in a shady, cool and dry place.
• Install the keypad away from equipments that produces heat or electric-magnetic, such as heater, air conditioner, microwave oven etc.
• Take the keypad for disposal of recycling according to the local regulation.
• Do not take apart the product if you are not a professional technician.

Maintenance

• You can get most dust corfinger print off with a dry, soft cloth or tissue.
• If there is dirt on the keypad, please wipe the surface by a soft cloth with a little dilute alkaline detergent and then wipe again with a dry cloth.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
  This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Preparation before Use

1. Make sure the battery has been installed correctly.
2. If you are using it for the first time, please connect the keypad to the power adapter.The LED indicator will flash while charging until it stays on, which means it is fully charged.
3. Remove the battery cover and turn on the power switch.

Pair the Keypad with the Main Panel
Scan QR Code

1. Reset the keypad until the status bar is flashing in 3 colors.
2. Launch the App, In the accessory management section, tap [Add Accessory].
3. Scan the QR Code on the keypad.
4. Follow the guideline in App and save the settings.

Pair the RFID Tag with the Main Panel
Scan QR Code

1. Make sure the keypad has been paired with the system.
2. Launch the App, In the accessory management section, tap [Add Accessory].
3. Scan the QR Code on the RFID Tag.
4. Follow the guideline in App and save the settings.
   You can try disarming the system by reading the RFID tag via keypad after pairing, to check if the tag has been correctly paired.

Usage

Activate Panel

1. When the keypad is in sleep mode, touching any button of the keypad will activate the keypad.
2. After being activated, the keypad will synchronize the real-time status with the alarm system immediately, the result will be represented by the status bar.
3. When there is no operation on the keypad, it will enter sleep mode within 10 seconds.
4. When the keypad is sleeping, it will not react to any signal sent from the system until the next activation.

Why sleep?

• Sleeping is the solution for long-time use when the keypad is in battery mode.
• When the power adapter is connected, it starts providing power and charging the battery. With the help of over-charging protective circuit, we recommend users to keep the adapter connected while using.If you don’t connect adapter, the Low battery indicator will light up once in 15 seconds and push notification will be sent to the APP. Please charge in time.

Arm/Disarm/Home Arm

• Input the operation code, and press [Arm] [Disarm] or [Home Arm] key.

• The status bar will flash once and then change the color as following pattern after command is executed correctly.

  • [Arm] : Red
  • [Disarm] : Green
  • [Home Arm] : Blue
    Note: The operation code can be set in the App.

• Read the RFID tag on the keypad panel, the system will Disarm immediately if the tag is paired before.

• Once the system is in SOS status and the keypad is activated, the status bar will be red-flashing and generate beep alarm sounds for 1 minute.

Appearance

FAQ

No response from keypad

|

Low Battery

|

Please connect the power adapter to charge the battery.If the problem is not solved, please contact the distributer for more help.

Wearing Gloves

| Take off the glove and try pressing the keypad again.

Keypad can’t be paired with the system

|

No response from the alarm system.

|

Make sure the alarm system is power ON and the App has already connected to the system.

Always make sure the location of the keypad installed can be covered by the RF signal sent from the alarm system. You can use a paired remote controller to test.

Can’t disarm by the RFID tag.

|

The RFID tag hasn’t paired with the alarm system.

|

Using the App to pair the RFID tag with the system.

Keypad is in power saving mode.|

Touch any button of the keypad to activate it.

[Arm] [Disarm] [Home Arm] failure|

Wrong operation password

|

Please input the right code. Users can modify the operation code in App, advanced setting–Reset PIN

Technical Specifications

Specifications

Working Humidity| ≤90%
Working Temperature| -10℃~50℃
Input| DC 5V __  1.5A
Battery| Lithium-ion Battery, 800mAH
Wireless Frequency| 433.92MHz / 868.35MHz
Transmission Distance| Up to 1000m without obstacle
Standby Time| 6 months for daily use(8 times per day, 30 seconds each time)
Weight| 180g with backup battery
Size| 144.5×91.8×20.8mm            (LxWxH)(±0.1mm)
Status Bar| 1 bar, 3 color(RED/GREEN/BLUE), upon the button area.
Power Switch| X1, beneath battery cover.
Reset Button| X1, pin hole, beneath battery cover.
Buttons| 13 Touch buttons
RFID Area| All front area around the buttons.
Materials| FRONT : PC, BACK : Non glassy surface to avoid scratches, WALL BRACKET : Non-glassy surface to avoid scratches
Wall Mounting| Using Mounting Bracket
Features
Power Saving| Supported, not supported while charging, the realtime status would be updated only when keypad is activated.
Pairing| Supports scanning QR Code for pairing.
Low Battery Warning| Supported. Color indicated on keypad and warning in APP.
Tamper Alarm| Supported
RFID Disarm| Supported, up to 99 RFID tags.
Reset| Supported

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>