FlightScope E19-GV354 Mevo Plus Launch Monitor Installation Guide
- June 1, 2024
- FlightScope
Table of Contents
FlightScope E19-GV354 Mevo Plus Launch Monitor
Product Information
Specifications
- Minimum Space/Area Required: 18′ x 13′ x 10′ (LxWxH, 5.5m x 4m x 3.1m)
- Recommended Simulator Layout Dimensions:
- 8′ min 2.4m from A to G
- 8′ min 2.4m from G to D
- 7′ 2.1m from G to E
- +/- 6 15cm variance for position E
- +/- 9 22cm variance for position F
- Simulator Hardware Required: Mevo+, device, artificial hitting strip, artificial putting strip, hitting cage with screen or net, data video projector, HDMI cable, Lightning to HDMI female adaptor (if using iPad), iPad or laptop
Product Usage Instructions
Setting Up the Simulator
- Ensure the required minimum space is available for setting up the simulator.
- Install the artificial hitting strip and put the strip as per the recommended dimensions.
- Position the hitting cage with a screen or net in the designated area.
- Connect the Mevo+ device, data video projector, and other hardware components as specified.
- Adjust the green speed setting in the simulator software according to your preference.
Using the Simulator
- Place the hitting ball on the hitting strip at position B.
- Position the putting ball on the putting strip at position D.
- Ensure a clearance of at least 1′ (0.3m) between the unit and any rear wall (position F).
- Mark the ball with metallic stickers for accurate spin results during hitting and chipping activities.
- Refer to the online FAQs for mat supplier recommendations and simulator setup queries.
Frequently Asked Questions (FAQ)
Q: Can I use the simulator outdoors without metallic stickers on the ball?
A: Yes, metallic stickers are recommended for hitting and chipping indoors for accurate spin results. They are not required for outdoor use.
Q: What is the recommended distance between the hitting strip and any wall?
A: Maintain a 1′ (0.3m) gap between your screen and any wall for optimal performance.
Q: How do I address electronic noise interference from appliances?
A: Certain appliances can cause electronic noise that may impact system performance. Refer to the online manual for troubleshooting steps or contact support for assistance.
Simulator Setup
- All setback distances are given on the reverse side of this card.
- Minimum space/area required: 18′ x 13′ x 10′ (LxWxH, 5.5m x 4m x 3.1m). There must be a 1′ (0.3m) gap between your screen and any wall. We also recommend a 1′ (0.3m) clearance between your unit and any rear wall.
- The hitting strip should be a durable artificial turf that can hold a tee. The putting strip should be smooth and be a medium to fast speed.* Contact support@flightscope.com or FAQs online at flightscopemevo.com/faq/ for mat supplier recommendations and any simulator questions you may have.
- Marking the ball with metallic stickers is recommended for hitting and chipping to give accurate spin results when using the Mevo+ with a simulator setup.
- You can also putt with marked balls, however, if you are playing outdoors, metallic stickers are not required.
- Certain appliances can cause electronic noise which can affect the performance of the system, causing for example missed shots. Please check the online manual available at flightscopemevo.com.
- Simulator hardware required: Mevo+, device, artificial hitting strip, artificial putting strip, hitting cage with screen or net, data video projector, HDMI cable, Lightning to HDMI female adaptor (if using iPad), iPad or laptop.
- The unit tilt angle should be 12° for simulator use. Use the simulator angle guide included to easily set the tilt angle.
- The green speed must be entered into the simulator software in settings.
Recommended simulator layout
- A Hitting strip (min 24″ x 12″ / 60 x 30cm)
- B Hitting ball position
- C Putting strip (min 18″ / 45cm wide)
- D Putting ball position
- E Mevo+
- F Clearance (min 1′ / 0.3m)
- G Mat / Surface
- H Screen/net
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>