POWER-POLE AVG-MP-0915 PV Extension Pulpit Instructions
- June 1, 2024
- POWER-POLE
Table of Contents
- POWER-POLE AVG-MP-0915 PV Extension Pulpit
- Product Information
- FAQ
- TOOLS AND HARDWARE
- DETERMINE MOUNTING LOCATION
- INSTALLATION INSTRUCTIONS
- 3 Phillips Head Screwdriver, tighten hardware snug using a 7/16” Socket &
- Contacts
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
- 2 Phillips Head Screwdriver
- 3 Phillips Head Screwdriver
POWER-POLE AVG-MP-0915 PV Extension Pulpit
Product Information
Specifications
- Hardware Included: Screws, Pulpit Plate, Rubber Washers, Stainless Steel Washers, Nylon Lock Nuts, Hex Head Bolts, Lock Washers
FAQ
- Q: What should I do if I encounter difficulties during installation?
- A: Contact our Customer Service Team at 1 + 813.689.9932 Option 2 for assistance.
TOOLS AND HARDWARE
TOOLS:
-
2 Phillips Head Screwdriver
-
3 Phillips Head Screwdriver
- 7/16” Socket
- 7/16” Wrench
- Ratchet
- Electric Drill
- 5-16” Drill Bit
INCLUDED HARDWARE
| QTY. | LABEL | ITEM # | DESCRIPTION |
|---|---|---|---|
| 6 | A | AVG-MH-SC-0318 | 1/4”-20, Full Thread, 3”, Stainless Flat-Head Phillips |
Drive Screw
1| B| AVG-MP-0936| Pulpit Plate, Short
6| C| AVG-MP-0915| Thick Rubber Washer
6| D| AVG-MH-WS-0306| 1/4” Large Stainless Steel Flat Washer
6| E| nut-14-tall| 1/4” Brass Tall Nylon Lock Nut
4| F| AVG-MH-BT-0320| 1/4”-20, 1 1/8” Stainless Hex Head Bolt
2| G| AVG-MH-BT-0319| 1/4”-20, 7/8” Stainless Hex Head Bolt
6| H| AVG-WASH-14-PP| 1/4” Stainless Lock Washer
6| I| AVG-MH-WS-0321| 1/4” Small Stainless Steel Flat Washer
DETERMINE MOUNTING LOCATION
After reading the Mounting Parameters lay the Pulpit B on the boat deck and line up the mounting holes on the included PV Mounting Template (included with trolling motor) with the holes on the Pulpit B . Move the Pulpit B into position so the Cam Arms have proper clearance and all parameters are met.
MOUNTING PARAMETERS
- Ensure there are no obstructions or sensitive components where the mounting hardware will be installed.
- Make sure the cam arms can have a full range of motion and will not hit the boat when the unit is deployed.
- Ensure there are no obstructions blocking the motor from fully deploying and stowing.
- If mounting to a curved Boat Deck, ensure Rubber Washers C are used between the Pulpit and Deck.
DRILL PILOT HOLES
- Drill Pilot holes for the Flat Head Screws A using a 5/16” Drill Bit.
- Use the furthest possible forward two holes, the furthest possible back two holes, and two holes that are spaced evenly in between the others.
Caution: Check the area beneath where the Pulpit will be mounted to ensure there are no hoses, wires lines tanks or other sensitive components.
IMPORTANT
- If installing to gel-coat, follow the drilling procedure in Appendix A of the Installation & Owner’s Guide to ensure you do not crack or chip the gel-coat.
- Make sure the cut-out is facing the front of the boat and the counter-sunk holes are facing upright.
INSTALLATION INSTRUCTIONS
INSTALL PULPIT
Install the Pulpit Mounting Hardware in order. While holding Screws A with a
3 Phillips Head Screwdriver, tighten hardware snug using a 7/16” Socket &
Wrench.
- (6) Screws A
- Pulpit B
- (6) Rubber Washers C if needed
- Boat Deck
- (6) Large Washers D
- (6) Nylon Lock Nuts E
NOTICE: If Installing the PV to Pulpit using a Quick Disconnect Mount, follow the Mounting the Move PV Section in the Installation Owner’s Guide.
Warning
- Always disconnect power by turning the main battery cutoff switch to the off position before performing any installations.
REMOVE SPRINGS AND SHROUDS
- STEP 1 Using a #2 Phillips Screwdriver, remove the (2) Screws that attach the Shroud Assembly.
- STEP 2 Rotate the Shroud Assembly so it is resting against the Die Cast Motor Housing.
- STEP 3 (Optional for easiest install) Remove the (2) Springs by pulling upward and sliding the spring eye off of the spring post.
REMOVE QUICK DISCONNECT HARDWARE
- STEP 1 While holding the rear two Flat Head Screws with a #3 Phillips Screwdriver, loosen the Hex Nuts using a 7/16” Socket and Ratchet, then remove hardware. FIG A
- STEP 2 Push down on and hold the Foot Pedal so the arms slide backward, allowing the additional (4) Screws to be accessed. FIG B
- STEP 3 Repeat STEP 1 for the remaining (4) Screws and hardware. FIG A
NOTICE
- You will need to use an extension to reach the front four nuts.
INSTALL PV TO PULPIT
Install the PV mounting hardware in order. Tighten hardware snug using a 7/16” Socket & Wrench.
- (6) Bolts ( F for the front four mounting holes, G for the rear two mounting holes)
- (6) Lock Washers H
- (6) Small Washers I
- Pulpit B
NOTICE
- You will need to use an extension to reach Bolts F .
- You will need to engage the Foot Release to reach Bolts F .
INSTALL SPRINGS AND SHROUDS
- STEP 1 Reinstall the (2) Springs.
- STEP 2 Flip the Shroud Assembly down, ensuring the Shrouds are interlocking not overlapping.
- STEP 3 Install the Screw on either side of the unit. Using a #2 Phillip’s Screwdriver, tighten snug.
Contacts
- 9010 Palm River Road, Tampa, Florida 33619
- phone 813.689.9932
- fax 813.689.8883
- power-pole.com
Power-Pole is a registered trademark of JL Marine Systems, Inc.
© Copyright 2023 JL Marine Systems, Inc. All Rights Reserved.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>