SEALEY CHT20V Cordless Hedge Trimmer Instruction Manual
- June 1, 2024
- SEALEY
Table of Contents
20V 52CM SV20 SERIES CORDLESS
HEDGE TRIMMER – BODY ONLY
MODEL NO: CHT20V
CHT20V Cordless Hedge Trimmer
Thank you for purchasing a Sealey product. Manufactured to a high standard,
this product will, if used according to these instructions, and properly
maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE
OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND
WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE
INSTRUCTIONS SAFE FOR FUTURE USE.
SAFETY
Always wear appropriate eye
protection, ear protection, substantial footwear, gloves, long trousers whilst
operating.
Remove ill fitting clothing.
Remove ties, watches, rings and other loose jewellery and contain long hair.
Inspect and ensure equipment is
in good working order before use.
Maintain and clean tool and
battery pack, regularly. Check air holes are clear.
Must be serviced by an
authorised agent. Use genuine parts only. Non authorised parts will invalidate
the warranty.
WARNING! Remove battery before: performing maintenance, carrying out
adjustments, inspecting the machine after striking an object, before clearing
a blockage, before leaving the tool unattended, before moving to the next job
location.
WARNING! Risk assess the
work area. Keep bystanders away from the work area. DO NOT operate with anyone
or pets nearby. Check intended work area for wildlife.
DO NOT use in bad weather conditions, especially when there is a risk of
lightning. DO NOT expose to rain. Only use in good light.
DO NOT use if tool vibrates abnormally, switch off, remove battery and then
inspect.
DO NOT touch hazardous moving parts. Allow to come to a complete stop first.
DO NOT operate whilst tired, ill under the influence of alcohol or other
intoxicating drugs.
DO NOT overreach and keep balance at all times.
DO NOT use if damaged. DO NOT operate with defective guards or shields or
without safety devices.
DO NOT use for a task it was not designed to perform.
Store with the battery removed
and separate from the machine, in a dry, childproof location.
WARNING! Never allow children, persons with reduced physical sensory or
mental capabilities or lack of experience and knowledge or people unfamiliar
with these instructions to use the machine, local regulations may restrict the
age of the operator.
INTRODUCTION
Lightweight cordless hedge trimmer makes gardening easy, clean and effective. Blade tip and blade head protector fitted for added user safety. Rear handle features a soft grip and swivel feature which can be adjusted through 3-positions, making it easier to get to the desired angle. Works in conjunction with our one one-battery-fits-all program. Requires compatible 20V battery and mains charger, sold separately.
SPECIFICATION
Model No:………………………………………………… CHT20V
Battery: ……….. 20V 2Ah – 6Ah Lithium-ion (not included)
Blade Length: ………………………………………………… 52cm
No-Load Speed: ……………………………………….. 2200spm
Teeth Distance: …………………………………………….. 14mm
Voltage: ………………………………………….. 20V Lithium-ion
Emission Sound Pressure Level: ……… 79dB(A) K = 3dB
Sound Pressure Level: ……………………. 70dB(A) K = 3dB
Sound Power Level: ……………………….. 90dB(A) K = 3dB
Vibration Level: ………………………a h ≤2.5m/s 2 K = 1.5m/s 2
Consumable Parts: CP20VBP2 – 2Ah Battery, CP20VBP4 – 4Ah Battery, CP20VBP6 –
6Ah Battery Replacement Parts: CP20VMC – Mains Charger (not included)
ASSEMBLY
4.1. FITTING THE HAND GUARD
4.1.1. Push home the hand guard (fig.1.C) in the direction of the arrow as
shown in fig.1. As it seats, it will click into place. Fasten with the 2 10mm
long self tapping screws (fig.1.B) as shown in fig.1.
4.1.2. Fully tighten the screws on both sides (Fig.1.B).
4.2. FITTING THE STEADY GRIP
4.2.1. Push home the steady grip (fig.1.D) in the direction of the arrow as
shown in fig.1. As it seats, it will click into place. Fasten with the 2 12mm
long self tapping screws (fig.1.A) as shown in fig.1.
4.2.2. Fully tighten the screws on both sides (fig.1.A).
OPERATION
5.1. SWITCHING ON/OFF
5.1.1. The hedge trimmer is equipped with a two-handed safety switch. The
machine works only when the switch on the steady grip (fig.2) is pressed with
one hand and the switch on the handle (fig.2) is pressed with the other hand.
If either switch is released, the cutters will stop moving. Please beware of
the cutters as they slow down to a standstill.
5.2. SWIVEL HANDLE
5.2.1. The hedge trimmer is fitted with a rear swivelling handle grip. It can
be swivelled 90° to either left and right of the vertical. To do so, pull the
slide (fig.3) in the direction indicated by the arrow and turn the handle.
5.2.2. To return the handle grip to its original position you must pull the
slide (fig.3) in the direction indicated by the arrow again. The handle grip
may be turned through 90° for vertical cuts.
MAINTENANCE
WARNING! Remove battery before attempting any cleaning, maintaining or
storing the device.
6.1. CLEANING
6.1.1. Keep all safety devices, air vents and the motor housing free of dirt
and dust as far as possible. Wipe the equipment with a clean cloth or blow it
with compressed air at low pressure.
6.1.2. Clean the equipment immediately each time you have finished using it.
6.1.3. Clean the equipment regularly with a moist cloth and some soft soap. DO
NOT use cleaning agents or solvents; these could attack the plastic parts of
the equipment.
6.1.4. Ensure that no water can seep into the device. The ingress of water
into an electric tool increases the risk of an electric shock.
6.1.5. Remove deposits from the guard hood with a brush.
6.2. CARBON BRUSHES
6.2.1. In case of excessive sparking, have the carbon brushes checked only by
a qualified electrician.
WARNING! The carbon brushes should not be replaced by anyone but a
qualified electrician.
6.3. MAINTENANCE
6.4. The cutters should be cleaned and lubricated at regular intervals in
order to ensure best performance at all times. Remove deposits with a brush
and apply a thin film of oil.
6.4.1. There are no parts inside the equipment which require additional
maintenance.
6.4.2. Store the trimmer with blade guard fitted.
WARNING! – Risk of Hand Arm Vibration Injury.
This tool may cause Hand Arm Vibration Syndrome if its use is not managed
adequately.
This tool is subject to the vibration testing section of the Machinery
Directive 2006/42/EC.
This tool is to be operated in accordance with these instructions.
Measured vibration emission value (a): 2.5m/s²
Uncertainty value (k): 1.5m/s²
Please note that the application of the tool to a sole specialist task may
produce a different average vibration emission. We recommend that a specific
evaluation of the vibration emission is conducted prior to commencing with a
specialist task.
A health and safety assessment by the user (or employer) will need to be
carried out to determine the suitable duration of use for each tool.
NB: Stated Vibration Emission values are type-test values and are intended to
be typical.
Whilst in use, the actual value will vary considerably from and depend on many
factors.
Such factors include; the operator, the task or consumable.
The state of maintenance of the tool itself is also an important factor, a
poorly maintained tool will also increase the risk of Hand Arm Vibration
Syndrome.
Health surveillance.
We recommend a programme of health surveillance to detect early symptoms of
vibration injury so that management procedures can be modified accordingly.
Personal protective equipment.
We are not aware of any personal protective equipment (PPE) that provides
protection against vibration injury that may result from the uncontrolled use
of this tool. We recommend a sufficient supply of clothing (including gloves)
to enable the operator to remain warm and dry and maintain good blood
circulation in fingers etc. Please note that the most effective protection is
prevention, please refer to the Correct Use and Maintenance section in these
instructions. Guidance relating to the management of hand arm vibration can be
found on the HSE website www.hse.gov.uk – Hand-Arm
Vibration at Work.
WEEE REGULATIONS
**** Dispose of this product at the end of its working life in compliance
with the EU Directive on Waste Electrical and Electronic Equipment (WEEE).
When the product is no longer required, it must be disposed of in an
environmentally protective way. Contact your local solid waste authority for
recycling information.
ENVIRONMENT PROTECTION
**** Recycle unwanted materials instead of disposing of them as waste. All
tools, accessories and packaging should be sorted, taken to a recycling centre
and disposed of in a manner which is compatible with the environment. When the
product becomes completely unserviceable and requires disposal, drain any
fluids (if applicable) into approved containers and dispose of the product and
fluids according to local regulations.
Note: It is our policy to continually improve products and as such we
reserve the right to alter data, specifications and component parts without
prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is
required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
sales@sealey.co.uk
www.sealey.co.uk
LED109 SERIES Issue 3 (H,2,3,4,F) 14/06/23Original Language Version
© Jack Sealey Limited
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>