ideal lux Pegaso SP12 Pegaso Chandelier Instruction Manual
- June 1, 2024
- ideal lux
Table of Contents
ideal lux Pegaso SP12 Pegaso Chandelier
Specifications:
- Model : Pegaso SP12
- Maximum Wattage : E14 max 12 x 28W
- Power Supply : 220-240V, 50/60 Hz
- Color Options : BIANCO (White), OTTONE (Brass)
- Manufacturer: IDEAL LUX s.r.l.
- Manufacturer Address: Via Taglio Destro 32, 30035 Mirano (VE), Italy
- Manufacturer Website : www.ideal-lux.com
Product Usage Instructions
Installation:
1. The lighting fitting should be installed by a qualified electrician.
2. Follow the assembly instructions by reading the numerical progression provided.
Safety Instructions:
1. Ensure the power supply is switched off before starting the installation or any maintenance work.
2. The product may have parts that can become hot, handle with caution.
3. Use appropriate fixing accessories specific to the material. Only use screws and plugs compliant with regulations.
4. Do not look directly at the light source.
Maintenance and Troubleshooting:
1. If the lamp does not turn on, replace the fuse.
2. Do not attempt to disassemble the LED light source as it is non- replaceable.
Electrical Safety Classes:
- Class I : Mandatory grounding connection for electrical safety.
- Class II : Double insulation or reinforced insulation, no grounding required.
- Class III : Low voltage supply (<50 Volts), no grounding needed.
Ingress Protection (IP) Ratings:
The product has different levels of protection against solid objects and dust, as indicated by the IP ratings.
FAQ
- Q: What should I do if the lamp is not turning on?
- A : Check and replace the fuse if necessary. If the issue persists, consult a qualified electrician for further assistance.
- Q: Can I replace the LED light source?
- A: The LED light source is non-replaceable. Do not attempt to disassemble it; consider consulting a professional for any issues related to the light source.
FEATURES
INSTALLATION
FOLLOW THE ASSEMBLY INSTRUCTIONS BY READING THE NUMERICAL PROGRESSION
THE LIGHTING FITTING SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN
THE SAFETY AND RELIABILITY ARE GUARANTEED ONLY WHEN INSTALLATION INSTRUCTIONS ARE PROPERLY FOLLOWED. PLEASE KEEP THIS INSTRUCTION SHEET FOR FUTURE REFERENCE.
SAFETY INSTRUCTIONS
- This fitting is produced and tested in accordance with the strictest European safety standards.
- This fitting cannot be disposed of as household waste. For disposal information ask the local authorities about how to collect it.
- As indicated by specific regulations, the lighting fitting should be installed by a qualified electrician.
- If the external wire is damaged it has to be replaced exclusively by the manufacturer, distributor or by a qualified electrician.
- Always isolate power before commencing installation, maintenance or repair.
- The luminaire contains certain parts which can be very hot.
- Each material requires specific mounting accessories. Use screws and wall plugs suitable for the material to which they are fastened. Those included may be unsuitable.
- Always tighten the screws firmly to avoid contact problems.
- This fitting should only be installed indoors.
- Luminaires are not suitable for recessed on normally flammable surfaces.
- Luminaire is not suitable for direct mounting on normal flammable surfaces.
- This fitting is only suitable for fixing to the ceiling.
- This fitting is only suitable for fixing to the wall.
- The weight of the lamp has to be supported by the chain. Adjust the length of the electric wire so that it is longer than the chain.
- Only use lamps that do not exceed the maximum specified wattage.
- Always observe the minimum distance between the lamp and the surface being lit, as shown in the icon. The lamp can cause a fire if the minimum distance is not observed.
- Auto-protected bulb. Only use bulbs marked with this symbol. Halogen bulbs get very hot. Wait until they cool down before replacing them.
- Cracked or broken safety glass has to be replaced immediately. Use only manufacturer-approved parts complying with regulations.
- Light source with not-substitutable light emitting diode (LED). Do not disassemble the product since the diodes can damage the eyes. Do not immerse in water. Wipe with a damp cloth. Do not use solvents or strong detergents.
- This fitting is equipped with a fuse. If the lamp is out of order, replace the internal fuse.
- Class | Electrical safety is guaranteed by the main insulation and an additional protective conductor (earthing) connected with the metal frame of the lamp. Earthing is obligatory.
- Class Il Electrical safety is guaranteed by the main insulation and double or reinforced insulation. Earthing is not necessary.
- Class Ill Electrical safety guaranteed by very low power supply (less than 50 Volt). Earthing excluded.
- Not protected.
- Protected against solid objects greater than 50 mm.
- Protected against solid objects greater than 12 mm.
- Protected against solid objects greater than 2,5 mm.
- Protected against solid objects greater than 1mm.
- Dust protected.
- Totally protected against dust infiltration.
- Not protected.
- Protected against vertically falling water drops.
- Protected against water drops falling with a maximum angle of 15° to the vertical axis.
- Protected against rain.
- Protected against splashing water.
- Protected against water jets.
- Protected against strong water jets.
- Protected against temporary immersion.
- Protected against prolonged immersion.
- The luminaire was not suitable for covering with thermally insulating material.
- Caution, risk of electric shock.
- Do not stare at the operating light source.
IDEAL LUX s.r.l.
Via Taglio Destro 32
30035 Mirano (VE) Italy
www.ideal-lux.com
IDEAL LUX Warehouse
Via delle Industrie, 8/D
30036 Santa Maria di Sala (Venezia)
8.00 – 12.00 / 13.30 – 17.00
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>