KARCHER K 7 WCM Premium High Pressure Cleaner Instruction Manual

KARCHER K 7 WCM Premium High Pressure Cleaner

Product Information

The K 7 WCM and K 7 WCM Premium are high-pressure washers designed for cleaning various surfaces. The product comes with a range of accessories, including a transport wheel, water connection with a built-in sieve, cleaning agent suction hose, power cable with plug, hose reel, high-pressure gun, a button for separating the high-pressure hose from the gun, high-pressure hose, transport handle, type plate, and screws. The product has safety features such as a locking high-pressure gun, auto-stop function, and motor protection switch. The product also has a water filter and cleaning agent filter.

Product Usage Instructions

1. Mounting the Transport Handle: Attach the transport handle and secure it with three screws. See Figure C.
2. Mounting the Hose Reel: Attach the hose reel and make sure it clicks in place. See Figure H and Figure I.
3. Water Supply: Check the water supply company’s regulations and connection values on the type plate or technical data chapter. Connect the garden hose to the water supply and thewater connection on the product. Make sure there are no air bubbles in the system and that water comes out of the high-pressure gun before starting.
4. Using with High-Pressure: Make sure the high-pressure gun is locked before starting. Release the lock to operate the gun. See Figure P.
5. Using with Cleaning Agent: Use cleaning agents that are suitable for high-pressure cleaners. Fill the cleaning agent container and attach the suction hose to it. Make sure to rinse the container after use.
6. Cleaning and Maintenance: Clean the water filter regularly and replace it if necessary. Clean the cleaning agent filter after each use. Store the product in a dry and frost-free place.

General notes

Read these original operating instruc-tions and the enclosed safety instruc- tions before using the device for the first time. Proceed accordingly. Keep both books for future reference or for future owners.

Environmental protection

The packing materials can be recycled. Please dispose of packaging in accordance with the environmental regulations. Electrical and electronic devices contain valua-ble, recyclable materials and often components such as batteries, rechargeable batteries or oil, which – if handled or disposed of incorrectly – can pose a potential danger to human health and the envi- ronment. However, these components are required for the correct operation of the device. Devices marked by this symbol are not allowed to be disposed of together with the household rubbish.

• Cleaning work producing in oily waste water, e.g. washing engines, washing undercarriage, etc., may only be performed at washing stations with an oil separator.
• Working with detergents may only be performed on watertight surfaces with connection to the waste water sewage system. Do not allow detergent to enter waterways or the soil.
• Extraction of water from public waterways is not permitted in some countries.

Notes on the content materials (REACH)
Current information on content materials can be found at: www.kaercher.de/REACH

Intended use

Use the high-pressure cleaner in private households only. The high-pressure cleaner is intended for cleaning ma-chines, vehicles, buildings, tools, façades, terraces, garden machines etc. using a high-pressure water jet.

Accessories and spare parts

Only use original accessories and original spare parts. They ensure that the appliance will run fault-free and safely. Information on accessories and spare parts can be found at www.kaercher.com.

Scope of delivery

The scope of delivery for the appliance is shown on the packaging. Check the contents for completeness when unpacking. If any accessories are missing or in the event of any shipping damage, please notify your deal-er.

Device description

For the illustrations, refer to the graphics page

• Illustration A
• Illustration B

1. Transport wheel
2. Water connection with integrated sieve
3. Detergent suction hose
4. Mains connection cable with mains plug
5. Mains connection cable storage compartment
6. Hose reel
7. Holder for high-pressure hose
8. Spray lance dirt blaster for stubborn soiling
9. Vario Power spray lance for common cleaning tasks The working pressure can be continuously in-creased from “SOFT” to “HARD”. To adjust the working pressure, release the trigger gun lever and turn the spray lance to the desired position. Deter-gent can be added to the water jet when the spray lance is turned all the way in the SOFT direction.
10. High-pressure gun
11. Button for separating the high-pressure hose from the high-pressure gun
12. High-pressure gun lever
13. High-pressure gun lock
14. High-pressure hose
15. Trigger “0/OFF” / “I/ON”
16. Storage for spray lance
17. Storage for high-pressure hose / mains connection cable
18. Transport handle
19. Storage for high-pressure gun
20. Quick coupling for high-pressure connection
21. Type plate
22. Water connection coupling
23. Garden hose (fabric reinforced, diameter at least 1/2 inch (13 mm), length at least 7.5 m, with com-mercially available quick coupling)
24. KÄRCHER suction hose for water supply from open containers (order no. 2.643-100)
25. Screws
26. High-pressure hose clip  additionally required

Safety devices

CAUTION Missing or modified safety devices!
Safety devices are provided for your own protection. Do not bypass, remove or render ineffective any safety devices.

Power switch
The power switch prevents unintentional operation of the device.

High-pressure gun lock
The lock locks the lever of the high-pressure gun and prevents the device from starting unintentionally.

Auto-stop function
If the lever of the high-pressure gun is released, the pressure switch turns off the pump and the high-pressure jet stops. The pump switches on again when the lever is pressed.

Motor circuit breaker
The motor circuit breaker shuts off the device if power consumption it too high.

Symbols on the device

• Do not aim the high-pressure jet may at persons, animals, live electrical equipment or the device itself.
• Protect the device against frost. The device may not be connected to the public drinking water network.

Installation

For the illustrations, refer to the graphics page. Fit the supplied loose parts onto the device before starting up the device. Place the screws provided and matching screwdriver at the ready.

Mounting the transport handle

1. Attach the transport handle.
2. Secure the transport handle with 3 screws. Illustration C

Mounting the storage option for the high-pressure hose / mains connection cable

1. Insert the storage option for the high-pressure hose/ mains connection cable into the holder at the centre of the transport handle. The storage option locks into place. Illustration D

Mounting the storage option for spray lances

1. Push in the storage option for the spray lances into the holder on the device.
2. Hold the storage option in the end position and secure it using a screw. Illustration E

Mounting the storage option for the high-pressure gun

1. Push in the storage option for the high-pressure gun into the holder on the device.
2. Hold the storage option in the end position and secure it using a screw. Illustration F

Mounting the storage option for the mains connection cable
Devices without a hose reel

1. Push in the storage option for the mains connection cable into the holder on the transport handle.
2. Hold the storage option in the end position and secure it using a screw. Illustration G

Mounting the high-pressure hose reel
Devices with a hose reel

1. Attach the holder for the hose reel.
2. Secure the holder using 2 screws. Illustration H
3. Attach the hose reel. The hose reel locks into place. Illustration I

Installing the water connection coupling

1. Screw the water connection coupling onto the water connection on the device. Illustration J

Initial startup

Note
Take care not to exceed the maximum permissible mains impedance at the connection point (see chapter Technical data).  Contact your electricity supplier in the case of any uncertainties regarding the mains grid impedance at your electrical connection point.

1. Place the device on a flat and level surface.

2. Unwind the high-pressure hose and eliminate any loops and twists.
   Note
   Devices with a hose reel During operation, the high-pressure hose must be completely unwound from the hose reel.

3. Insert the high-pressure hose into the high-pressure gun until it audibly latches into place. Illustration K
   Note
   Take care to ensure the correct alignment of the nipple.

4. Insert the high-pressure hose into the quick coupling until it audibly latches into place. Illustration L

5. Check for a secure connection by pulling on the high-pressure hose.

6. Plug the mains plug into a mains socket.

Water supply
For the connection values, see the type plate or chapter Technical data. Observe the water distribution company regulations.

ATTENTION
Damage through contaminated water Contamination in the water can damage the pump and the accessories. KÄRCHER recommends using the KÄRCHER water filter for protection(special accessory, order number 4.730-059).

Connection to the water line

ATTENTION
Hose coupling with Aquastop on the water connection of the device Damage to the pump Never use a hose coupling with Aquastop on the water connection of the device. You can use an Aquastop coupling on the tap.

1. Plug the garden hose onto the water connection coupling.
2. Connect the garden hose to the water line. Illustration M
3. Open the water tap fully.

Sucking water from open containers
When used with the KÄRCHER suction hose with check valve (special accessory, order number 2.643-100) this high-pressure cleaner is suitable for sucking up surface water, e.g. from rain barrels or ponds (for the maximum suction height see chapter Technical data). The water connection coupling is not required for vacuuming operation.

1. Fill the suction hose with water.
2. Screw the suction hose onto the device water connection and hang it in a water source (e.g. water butt).

Vent the device

1. Switch the device on “I/ON”.
2. Unlock the lever of the high-pressure gun.
3. Press the lever of the high-pressure gun. The device switches on.
4. Allow the device for run a maximum of 2 minutes until the water escaping from the high-pressure gun is free of air bubbles.
5. Release the lever of the high-pressure gun.
6. Lock the lever of the high-pressure gun.

Operation

ATTENTION
Pump running dry Damage to the device If pressure does not build up in the device after 2 minutes then switch the device off and proceed according to the instructions in chapter Troubleshooting guide.

High-pressure operation

ATTENTION
Damage to painted or sensitive surfaces Surfaces can be damaged when the jet is too close to the surface or an unsuitable spray lance is used. Maintain a minimum spray distance of 30 cm when cleaning painted surfaces. Do not clean car tyres, paint or sensitive surfaces such as wood with the dirt grinder.

1. Insert a spray lance into the high-pressure gun and lock it by turning it 90°. Illustration N
2. Switch the device on (“I/ON”).
3. Unlock the lever of the high-pressure gun.
4. Press the lever of the high-pressure gun.The device switches on.

Operation with detergent

DANGER
Failure to adhere to the safety data sheet Incorrect handling of the detergent can seriously damage your health Observe the safety data sheet of the detergent manufacturer, in particular the instructions on personal protective equipment.

Note
KÄRCHER detergents ensure fault-free operation. Ask us for a consultation, request our catalogue or our detergent information sheets.

Note
Detergent can only be mixed into the jet at low pressure.

1. Pull the desired length of the detergent suction hose out of the casing. Illustration O
2. Hang the detergent suction hose in a container with detergent solution.
3. Use the Vario Power spray lance.
4. Turn the spray lance all the way into the “SOFT” position. The detergent solution is mixed with the water jet during operation.

Recommended cleaning method

1. Spray the detergent sparingly on the dry surface and let it work for a while (do not let it dry).
2. Rinse off the loosened dirt with the high-pressure jet.

After operation with detergent

1. Flush the device with clear water for approx. 30 seconds.

Interrupting operation

1. Release the lever of the high-pressure gun. The device switches off when the lever is released. The high pressure in the system is retained.
2. Lock the lever of the high-pressure gun. Illustration P
3. Switch the device off “0/OFF” during work breaks longer than 5 minutes.

Ending operation

CAUTION
Pressure in the system Injuries from high-pressure water escaping uncontrollably Only disconnect the high-pressure hose from the high-pressure gun or the device when the system is fully depressurised.

1. Release the lever of the high-pressure gun.
2. Close the water tap.
3. Press the lever of the high-pressure gun for 30 seconds. The pressure remaining in the system is discharged.
4. Release the lever of the high-pressure gun.
5. Lock the lever of the high-pressure gun.
6. Disconnect the device from the water supply.
7. Switch off the device “0/OFF”.
8. Pull the mains plug out of the socket.

Transport

CAUTION
Failure to observe the weight Risk of injury and damage Be aware of the weight of the device during transportation.

Pulling the device

1. Pull the device via the transport handle.

Transporting the device in a vehicle

1. Secure the device against slipping and tipping over.

Storage

CAUTION
Risk of injury and damage! The device may tip over on sloping surfaces. Be aware of the weight of the device during storage.

Storing the device

1. Place the device on a level surface.

2. Disconnect the spray lance from the high-pressure gun.

3. Press the separation button on the high-pressure gun and disconnect the high-pressure hose from the high-pressure gun.

4. Press the casing of the high-pressure hose quick coupling in the direction of the arrow and pull out the high-pressure hose.

5. Stowing the high-pressure hose.
   Devices without a hose reel
   Store the high-pressure hose on the device.
   Devices with a hose reel

   • Insert one end of the high-pressure hose into the
     opening at the front of the hose reel.

   • Turn the crank to wind up the high-pressure hose.

   • While doing so, guide the high-pressure hose with the second hand. Illustration Q

   • Fasten the coiled high-pressure hose to the hose reel with the high-pressure hose clip. Illustration R

6. Stow the mains connection cable on the device.

7. Stow both spray lances and the high-pressure gun in the appropriate storage options.
   Observe the additional instructions before storing the device for a longer period of time, see chapter Care and service.

Frost protection

ATTENTION

Danger of frost
Incompletely emptied devices can be destroyed by frost. Completely empty the device and accessories. Protect the device from frost.

The following requirements must be satisfied:

• The device is disconnected from the water supply.
• The high-pressure hose is removed.
  1. Switch the device on “I/ON”.
  2. Wait for a maximum of 1 minute until no more water escapes from the high-pressure connection.
  3. Switch off the device.
  4. Store the device in a frost-protected room, together with all accessories.

Care and service

DANGER
Danger of electric shock Injuries due to touching live parts Switch off the device. Remove the mains plug. The device is maintenance-free, i.e. you do not need to perform any maintenance work.

Clean the sieve in the water connection

ATTENTION
Damaged sieve in the water connection Damage to the device through contaminated water Check the sieve for damage before inserting it in the water connection.
If necessary, clean the sieve in the water connection.

1. Remove the water connection coupling.
2. Pull the sieve out.
3. Clean the sieve under running water. Illustration S
4. Insert the sieve into the water connection.

Clean the detergent filter
Clean the detergent filter before longer periods of storage.

1. Pull the filter off the detergent suction hose.
2. Clean the filter under running water. Illustration T

Troubleshooting guide

Malfunctions often have simple causes that you can remedy yourself using the following overview. When in doubt, or in the case of malfunctions not mentioned here, please contact your authorised Customer Service.

DANGER

Danger of electric shock

• Injuries due to touching live parts
• Switch off the device.
• Remove the mains plug.

Device not running

1. Press the lever of the high-pressure gun. The device switches on.
2. Check that the voltage specified on the type plate corresponds to the voltage of the power source.
3. Check the mains connection cable for damage.
4. If the motor is overloaded and the motor circuit breaker has triggered:
   • Switch off the device “0/OFF”.
   • Allow the device to cool down for 1 hour.
   • Switch the device on “I/ON” and resume operation. Have the device checked by Customer Service if this fault occurs repeatedly.

The device does not start up, the motor buzzes

Voltage drop due to a weak mains grid or when using an extension cable

1. When switching on, first press the lever on the high-pressure gun and then switch on the device “I/ON”.

Device does not reach required pressure

The water supply is too low.

1. 1. Open the water tap fully.

2. Check the water inlet for an adequate flow rate.
3. Check the setting at the spray lance.
4. Check that the maximum suction height is not exceeded.

The sieve in the water connection is dirty.

1. Pull the sieve in the water connection out using flat pliers.
2. Clean the sieve under running water. Illustration S

Air is in the device.

1. Vent the device:
   • Switch on the device without a connected spray lance for a maximum of 2 minutes.
   • Press the high-pressure gun and wait until the water escaping from the high-pressure gun is free of air bubbles.
   • Connect the spray lance.

Strong pressure fluctuations

1. Clean the high-pressure nozzle:
   • Use a needle to remove dirt from the nozzle drill.
   • Rinse the high-pressure nozzle from the front with water.
2. Check the water supply volume.

Device leaking

1. The device leaks a small amount for technical reasons. If the leak is severe, request authorised Customer Service.

Detergent is not sucked in

1. Use the Vario Power spray lance and turn it all the way in the “SOFT” direction.
2. Clean the filter on the detergent suction hose.
3. Check the detergent suction hose for kinks.

Warranty

The warranty conditions issued by our relevant sales company apply in all countries. We shall remedy possible  malfunctions on your appliance within the warranty period free of cost, provided that a material or manufacturing defect is the cause. In a warranty case, please contact your dealer (with the purchase receipt) or the next authorised customer service site. (See overleaf for the address)

Technical data

Exception according to Regulation (EU) 2019/1781 Annex I Section 2 (12): j) Subject to technical changes without notice.

EU Declaration of Conformity

We hereby declare that the machine described below complies with the relevant basic safety and health requirements in the EU Directives, both in its basic design and construction as well as in the version placed in circulation by us. This declaration is invalidated by any changes made to the machine that are not approved by us.

• Product: High-pressure cleaner
• Type: 1.317-xxx

Currently applicable EU Directives

• 2006/42/EC (+2009/127/EC)
• 2014/30/EU
• 2011/65/EU
• 2000/14/EC
• 2009/125/EC

Commission Regulation(s)

• (EU) 2019/1781

Harmonised standards used

• EN 60335-1
• EN 60335-2-79
• EN 62233: 2008
• EN 55014-1: 2017 + A11: 2020
• EN 55014-2: 1997 + A1: 2001 + A2: 2008
• EN 61000-3-2: 2014
• EN 61000-3-11: 2000
• EN IEC 63000: 2018

Applied conformity evaluation method
2000/14/EG: Annex V

Sound power level dB(A)

• Measured: 88
• Guaranteed: 91

The signatories act on behalf of and with the authority of the company management.

Documentation supervisor: S. ReiserAlfred Kärcher SE & Co. KG Alfred-Kärcher- Str. 28 – 40 71364 Winnenden (Germany) Ph.: +49 7195 14-0 Fax: +49 7195 14-2212 Winnenden, 2022/10/01

THANK YOU!

•  DANKE!
• Register your product and benefit from many advantages.
• Rate your product and tell us your opinion.
• www.kaercher.com/welcome
• www.kaercher.com/dealersearch

Alfred Kärcher SE & Co. KG Alfred-Kärcher-Str. 28-40 71364 Winnenden (Germany)

• 4-2-HC-A5-GS

References

• Cher - Official Site
• Cleaning equipment and pressure washers | Kärcher International
• Dealer Search | Kärcher International
• Home and Garden Warranty Registration USA - Kärcher
• Reinigungsgeräte und Hochdruckreiniger | Kärcher

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>