ZEBRA ZT211 Direct Thermal Printer Instruction Manual

June 3, 2024
ZEBRA

ZEBRA ZT211 Direct Thermal Printer logo

ZEBRA ZT211 Direct Thermal Printer

ZEBRA ZT211 Direct Thermal Printer product

Parts List

Before proceeding, verify that your kit contains the following items. To reorder specific parts, navigate to zebra.com/parts, and select your printer model.

Cutter assembly| ZEBRA ZT211 Direct Thermal Printer 01| Qty 1
---|---|---
Cutter catch tray| | Qty 1
Screw: M4X.7X10 so flng zn| | Qty 1

Tools NeededZEBRA ZT211 Direct Thermal Printer 20

  • Metric hexagon keys or bits
  •  Hexalobular (6-lobe, star) keys, drivers, or bits
  •  Sorting bin for screws and small parts (optional)

Prepare for Installation

NOTE:
Retain all parts removed during disassembly, unless otherwise directed.
CAUTION—ESD:
Observe proper electrostatic safety precautions when handling static-sensitive components such as circuit boards and printheads.

  1. Turn off the printer and disconnect it from the power source.
  2. Disconnect all data cables.
  3. Open the media cover.ZEBRA ZT211 Direct Thermal Printer 04
  4. Remove media and ribbon (if used).

Remove the Lower Front Trim Panel

  1. Release the tear lower front panel by pushing down the two tabs that secure it to the printer. Use a flat- blade screwdriver to push down the inner tab.
  2.  Tip the top of the tear lower front panel away from the printer until the mounting tabs separate from the mounting slots.
  3.  Remove the tear lower front panel from the printer.
Install the Cutter Assembly

CAUTION:
The cutter blade is sharp. Do not touch or rub the blade with your fingers.

  1.  Slide the cutter assembly onto the mounting hooks, ensuring that the tabs slide into the slots on the printer base.ZEBRA ZT211 Direct Thermal Printer 07
  2. Install the 3mm mounting screw that secures the cutter assembly to the printer.ZEBRA ZT211 Direct Thermal Printer 08
  3. Install the cutter catch tray (if desired).ZEBRA ZT211 Direct Thermal Printer 09

Remove the Electronics Cover

  1. Remove the T10 screw that secures the electronics cover to the media side of the printer.ZEBRA ZT211 Direct Thermal Printer 10
  2.  Remove the three T10 screws that secure the electronics cover to the electronics side of the printer.ZEBRA ZT211 Direct Thermal Printer 11
  3. Lift the electronics cover off of the printer.ZEBRA ZT211 Direct Thermal Printer 12

Connect the Cutter Cable

  1.  Connect the cutter cable to the cutter assembly (1).ZEBRA ZT211 Direct Thermal Printer 13
  2.  From the media side, thread the end of the cutter cable through the hole to the electronics side (1).ZEBRA ZT211 Direct Thermal Printer 14
  3. Route the cutter cable from the hole to the media side (3) through the clip attached to the power supply (2), and then connect it to J11 on the MLB (1).ZEBRA ZT211 Direct Thermal Printer 15
Install the Electronics Cover
  1. Slide the electronics cover onto the printer.ZEBRA ZT211 Direct Thermal Printer 16
  2.  Install the three  T10 screws that secure the electronics cover to the electronics side of the printer.ZEBRA ZT211 Direct Thermal Printer 17
  3. Install the T10 screw that secures the electronics cover to the media side of the printer.ZEBRA ZT211 Direct Thermal Printer 18

Resume Printer Operation

  1.  Reinstall media and ribbon (if used).
  2.  Close the printhead assembly.
  3. Close the media cover.ZEBRA ZT211 Direct Thermal Printer 19
  4.  Reconnect the AC power cord and interface cables.
  5.  Turn on the printer power.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals