BOSCH SMS6ZCW10G Dishwasher Instruction Manual
- June 1, 2024
- Bosch
Table of Contents
BOSCH SMS6ZCW10G Dishwasher
Specifications :
- Model : Dishwasher
- Water Hardness Settings: Soft, Medium, Hard
- Special Salt Dispenser
- Rinse Aid Dispenser
- Programmes: Multiple with varying durations, energy consumption, and water usage
- Machine Care Programme
- Favourite Programme
Product Usage Instructions
Setting up Home Connect:
- Install the Home Connect app on your mobile device.
- Follow the instructions on the app.
- Scan the QR code with the Home Connect app.
Overview of Water Hardness Settings:
Refer to the table in the instruction manual to select the appropriate
water hardness setting.
Adding Special Salt:
- Unscrew the lid of the special salt dispenser.
- Fill the dispenser with water on initial start-up.
Adding Rinse Aid :
- Press the catch on the lid of the rinse aid dispenser and lift.
- Add rinse aid up to the max mark.
- Close the lid of the rinse aid dispenser.
Setting the Water Softening System:
- Open the basic settings by pressing a specific button for 3 seconds.
- Select the right water hardness by pressing a certain button repeatedly.
- Save the settings by pressing a button for 3 seconds.
Programmes:
Choose the appropriate programme based on duration, energy consumption, and
water usage.
How to Use Your Appliance:
- Load suitable tableware into the dishwasher after removing large food remnants.
- Add detergent to the dry detergent dispenser.
- Switch on the appliance.
- Select the programme.
- Start the programme.
- Remove tableware at the end of the programme.
- To cancel a programme, press a specific button for approximately 4 seconds.
Cleaning Filters:
After each wash, check and clean the filters to ensure optimal performance.
FAQ:
- Q: When should I add special salt to the dispenser?
A: Only add special salt just before starting a programme to avoid damage to the appliance.
Before using for the first time, read the instruction manual and the safety information it contains.
Setting up Home Connect
Tip: Connect your appliance to a mobile device. You can conveniently change all settings using the Home Connect app.
- Install the Home Connect app on your mobile device and follow the instructions.
- Scan the QR code with the Home Connect app.
Overview of water hardness settings
- You can find an overview of the water hardness values that can be selected here.
- A table of country-specific units can be found in the instruction manual.
Setting the water softening system
- Press .
- To open the basic settings, press Setup 3 sec. for 3 seconds.
- The display shows Hxx.
- The display shows .
- Press Start repeatedly until the right water hardness has been set.
- To save the settings, press Setup 3 sec. for 3 seconds.
Programmes
- The programme data has been measured in the laboratory according to
- European standard EN 60436.
- The consumption figures depend on the programme and additional function selected.
- The running time will change if the rinse aid system is switched off or rinse aid needs to be added
Programme
- Duration [h: min]
- Energy consumption [kWh]
- Water [l]
Suitable programme for running at night: it takes longer, but is extremely quiet
Adding special
salt
To avoid damage to the appliance, only add special salt to the dispenser for
special salt just before the programme starts.
- Unscrew the lid of the dispenser for special salt and remove.
- On initial start-up: Fill the dispenser right up with water.
- Add the special salt to the dispenser. The water in the dispenser is displaced and forced out. Never add detergent.
- Place the lid back on the dispenser and turn to close.
Adding rinse aid
- Press the catch on the lid of the dispenser for rinse 1 aid and lift 2 .
- Add rinse aid up to the max mark.
- Close the lid of the dispenser for rinse aid.
- The lid clicks into position.
Adding detergent
- Add the detergent to the dry detergent dispenser.
- Close the lid of the detergent dispenser.
- The lid clicks into position.
How to use your appliance
- Load the tableware. Only clean tableware that is suitable for dish washers. Remove large remnants of food from the tableware. Check that the spray arms can rotate freely.
- Add detergent.
- Switch on the appliance .
- Select the programme.
- Start the programme START
- Remove the tableware at the end of the programme.
- To cancel the programme, press RESET 4SEC for approx. 4 seconds. The programme is cancelled and ends after approx. 1 minute
Cleaning filters
- After each wash check the filters for residue.
- Turn the coarse filter anticlock-wise 1 and re-move the filter system 2.
- Pull down the micro filter to remove.
- Press the locking catches 1 together and lift the coarse filter out 2.
- Clean the filter elements under running water.
- Re-assemble the filter system.
- Insert the filter system into the appliance and turn the coarse filter clockwise. Make sure that the arrow markings match up.
Cleaning spray arms
-
Unscrew the upper spray arm 1 and pull down to remove 2
-
Pull up the lower spray arm to remove..
-
Check the outlet nozzles on the spray arms for blockages under running water and remove any foreign bodies.
-
Insert the lower spray arm.
The spray arm clicks into position. -
Insert the upper spray arm and screw it firmly in place.
Clean wastewater pump
- Disconnect the appliance from the power supply.
- Remove the filter system.
- Scoop out any water.
- Prise off the pump cover using a spoon and grip it by the crosspiece.
- Lift the pump cover inwards at an angle and remove.
- Remove any remnants of food and foreign bodies in the area of the impeller.
- Insert the pump cover 1 and press down 2 . The pump cover clicks into position.
- Install the filter system.
Troubleshooting