Metra 99-3410 Chevrolet Tracker Dash Kit Installation Guide

Table of Contents

Preparation

Disconnect the negative battery terminal to prevent short circuits.
Gather the necessary tools including a Phillips screwdriver, cutting tool, wrench, etc.

Radio Housing Installation

Cut and remove all mounting tabs on the radio housing except specific tabs identified.
Remove climate control knobs, cigarette lighter, and ashtray if applicable.
Unclip the radio trim bezel and remove any screws exposed.

Factory Unit Removal

Aftermarket Unit Installation

Slide the aftermarket head unit into the kit and secure it with shaft nuts.
Cut and remove shaft supports if necessary.
Slide the DIN cage into the radio housing and secure it by bending the metal locking tabs down.

Frequently Asked Questions (FAQ)

Q: Why is it important to disconnect the negative battery terminal?

A: Disconnecting the negative battery terminal prevents accidental short circuits during installation.

Q: How do I identify the mounting tabs on the radio housing?

A: The mounting tabs can be identified by the stamped letter on the back of each tab. Cut and remove all tabs except those specified.

Q: What tools are required for installation?

A: Tools such as a Phillips screwdriver, cutting tool, wrench, etc., are necessary for a successful installation.

CHEVROLET Tracker 1998-04 • GEO Tracker 1992-97 SUZUKI Sidekick 1992-98 / Vitara series 1999-04

Disconnect the negative battery terminal to prevent an accidental short circuit.
Remove the cigarette lighter and climate control knobs.
Remove the ashtray and (1) screw exposed. Pull out the climate control cluster and remove (2) screws exposed.
Unclip the radio trim bezel.
Remove (4) screws from the factory head unit, slide the unit out, and disconnect the wiring.
Cut and remove all mounting tabs on the Radio Housing EXCEPT tab “B”. (The mounting tabs can be identified by the stamped letter on the back of each tab). (see Fig. A).
Cut and remove the (2) side clips on the back side of the radio trim bezel. (This will provide proper clearance when re-attaching the bezel after the aftermarket head unit has been installed) (see Fig. B).
Skip to the Installation Instructions for ALL VEHICLES.

GEO Metro / SUZUKI Swift 1992-94

Disconnect the negative battery terminal to prevent an accidental short circuit. Remove the climate control knobs. Remove (1) Phillips screw above and (2) Phillips screws below the climate controls.
Unclip the radio trim bezel. Remove (4) screws from the factory head unit, slide the unit out, and disconnect the wiring.
Cut and remove all mounting tabs on the
Radio Housing EXCEPT for tabs “A”. The mounting tabs can be identified by the stamped letter on the back of each tab. Skip to the Installation Instructions for ALL VEHICLES.

SUZUKI Aerio 2003

Disconnect the negative battery terminal to prevent an accidental short circuit. Unclip the dash trim bezel and remove it. Remove (4) Phillips screws securing the factory head unit and disconnect the wiring.
Cut and remove all mounting tabs on the Radio Housing EXCEPT tab “B”. The mounting tabs can be identified by the stamped letter on the back of each tab. Skip to the Installation Instructions for ALL VEHICLES.

SUZUKI Esteem 1995-03

Disconnect the negative battery terminal to prevent an accidental short circuit. Remove the climate control knobs. Remove (1) Phillips screw located above the radio opening.
Unclip the radio trim bezel.
Remove (4) screws from the factory head unit, slide the unit out, and disconnect the wiring.
Cut and remove all mounting tabs on the Radio Housing EXCEPT tab “B”. The mounting tabs can be identified by the stamped letter on the back of each tab. Skip to the Installation Instructions for ALL VEHICLES.

ALL VEHICLES

2-SHAFT HEAD UNITS:
- Slide the aftermarket head unit into the kit and secure it with shaft nuts. (see Fig.A)
DIN HEAD UNITS:
- Cut and remove the shaft supports. Slide the DIN cage into the Radio Housing and secure it by bending the metal locking tabs down. Slide the aftermarket head unit into the cage until secure. (see Fig.B)
IF AN EQUALIZER WILL BE INCLUDED:
- Slide the aftermarket equalizer into the back of the Radio Housing.
- Using the hardware included with the equalizer, mount the unit to the kit. (see Fig. A)
IF AN EQUALIZER WILL NOT BE INCLUDED:
- Snap the Equalizer Dummy Plate into the Radio Housing. (see Fig. B)
Locate the factory wiring harness in the dash. Metra recommends using the proper mating adaptor and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuits).
Re-connect the battery terminal and test the unit for proper operation. Slide (4) Speed Clips over the holes in the sub-dash mounting brackets and mount the head unit/kit assembly with (4) Phillips Pan-Head Screws supplied.

WIRING AND ANTENNA CONNECTIONS (Sold Separately)

Harness:
- Please visit www.metraonline.com for specific interface applications
Antenna Adapter:
- 40-GM10 – GM antenna adapter 88-up

KNOWLEDGE IS POWER

Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry.
Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.
1-800-221-0932 www.metraonline.com
© COPYRIGHT 2001-2009 METRA ELECTRONICS CORP.