SUNELL SN-NVR3964E8-JR Network Video Recorder User Guide

SUNELL SN-NVR3964E8-JR Network Video Recorder

Precautions

Fully understand this document before using this device, and strictly observe rules in this document when using this device. If you install this device in public places, provide the tip “You have entered the area of electronic surveillance” in an eye-catching place. Failure to correctly use electrical products may cause fire and severe injuries.

WARNING| It alerts you to moderate dangers which, if not avoided, may cause minor or moderate injuries.
---|---
CAUTION| It alerts you about risks. Neglect of these risks may cause device damage, data loss, device performance deterioration, or unpredictable results.
NOTE| It provides additional information.

WARNING

• Strictly observe installation requirements when installing the device. The manufacturer shall not be liable for device damage caused by users’ non-conformance to these requirements.
• Strictly conform to local electrical safety standards and use power adapters that are marked with the LPS standard when installing and using this device. Otherwise, this device may be damaged.
• Use accessories delivered with this device. The voltage must meet input voltage requirements for this device.
• If this device is installed in places with unsteady voltage, ground this device to discharge high energy such as electrical surges in order to prevent the power supply from burning out.
• When this device is in use, ensure that no water or any liquid flows into the device. If water or liquid unexpectedly flows into the device, immediately power off the device and disconnect all cables (such as power cables and network cables) from this device.
• If this device is installed in places where thunder and lightning frequently occur, ground the device nearby to discharge high energy such as thunder strikes in order to prevent device damage.

CAUTION

• Avoid heavy loads, intensive shakes, and soaking to prevent damages during transportation and storage. The warranty does not cover any device damage that is caused during secondary packaging and transportation after the original packaging is taken apart.
• Protect this device from fall-down and intensive strikes, keep the device away from magnetic field interference, and do not install the device in places with shaking surfaces or under shocks.
• Clean the device with a soft dry cloth. For stubborn dirt, dip the cloth into slight neutral cleanser, gently wipe the dirt with the cloth, and then dry the device.
• Do not jam the ventilation opening. Follow the installation instructions provided in this document when installing the device.
• Keep the device away from heat sources such as radiators, electric heaters, or other heat equipment.
• Keep the device away from moist, dusty, extremely hot or cold places.
• If the device is installed outdoors, take insect- and moistureproof measures to avoid circuit board corrosion that can affect monitoring.
• Remove the power plug if the device is idle for a long time.
• When unpacking, please first confirm whether fragile label is damaged, if damaged, please contact customer service or sales personnel in time. The company will not be liable for any humanmade damage to fragile labels.

Special Announcement

• All complete products sold by the manufacturer are delivered along with nameplates, quick setup guide and accessories after strict inspection. The manufacturer shall not be liable for counterfeit products.
• The manufacturer will update this manual according to product function enhancement or changes and regularly update the software and hardware described in this manual. The updated content will be added to new versions of this manual without prior notice.
• This manual may contain misprints, technology information that is not accurate enough, or product function and operation description that is slightly inconsistent with the actual product, the final interpretation of company is as a standard.
• This manual is only for reference and does not ensure that the information is totally consistent with the actual product. For consistency, see the actual product.

NOTE

For more information, please refer to our website.

Package List

Open the package, check the appearance of product for no obvious damage, and confirm whether the items are consistent with the list.

Table 1-1 Packing list

Device Structure

Device Ports

NOTE: Different devices may have different ports and multi-head cables; Please refer to the actual product.

For front panel description of device refer to table 2-1.

Table 2-1 Front panel description

PWR

Indicator

| When the NVR is operating, the PWR indicator is steady on. When the NVR is shut down, the PWR indicator is off.
HDD

Indicator

| Hard disk status indicator.

This indicator flashes when data is transmitted.

USB 2.0| Support connected to an USB mouse or USB disk.

• For rear panel description of device, please refer to table 2-2.

Table 2-2 Rear panel description

cameras.
Audio out/ Audio in| Audio output and audio input.
VGA| Video output interface. If the Auxiliary Screen is enable, HDMI1’s output is main screen, VGA’s output is auxiliary screen.
HDMI1/2
e SATA| External hard disk interface.
USB 3.0| Support connected to 3.0 U disk.
RS232| Standard Rs232 serial communication interface of the device.
ALARM I/O RS 485| Alarm input and alarm output, 1A&1B~4A/4B are alarm out. A is RS 485+, B is RS 485-.
| Safe ground screw of the device.
| Power switch.
| AC 110V/220V power input interface.

Device Dimensions

NOTE: Different devices may have different dimensions; Please refer to the actual product.

Figure 2-1 Dimensions (Unit:mm)

Device Installation

The hard disks of the NVR must be provided by the user. Take the following steps to install the hard disks：

• Step 1 Remove the screws for fixing the cover and take down the cover. Remove the screws of bracket and side way, take over the two panels. Remove the cover of power panel to plug the redundant power supplies on.
• Step 2 Put the four hard disks under every panel, then fix the screws for hard disk, as shown in figure.

Device Operation

Startup
Before starting NVR, ensure that the NVR is connected to a power supply properly and a monitor is connected to the HDMI or VGA interface of the NVR correctly. After starting the NVR, there is a login window located in the center, as shown in figure 4-1.

CAUTION

In some environments, if the power supply is abnormal, the NVR may not work properly. In severe cases, the NVR may be damaged. In these environments, it is recommended to use regulated power supply.

NOTE

• The default name is admin, and NVR needs to activate, please create new password of device and channels to activate.
• Users can set pattern to unlock quickly.
• Users can change the system display language on the login window.

Topology of the NVR
For the cameras and NVR device are on Internet, or at same network, NVR and IP cameras can communicate with each other smoothly with WAN port. Figure 4-3 shows the network topology of the NVR.

Special Function
Some functions are applicable for some special cameras, such as Microphone, Human thermometer, Smart, Intelligent Analysis, Advanced Intelligent Analysis, please refer to actual camera channels.

Power off
Enter the Main Menu >System > Maintenance > Shutdown to power off the NVR. Or turn off the power switch.

Quick menu
Put the mouse arrow on bottom of live video interface, the quick menu will be showing. You can set layout to view live video, switch the split screen, auto sequence, volume, playback, thermal and so on.

Quick Configuration

• Plug in power to access the NVR user page. The wizard window would show at first time, users can configure quickly or close immediately. For configuration details please refer to main menu.
• Right-click on the main interface at any where to access the main menu. Main menu comprises Channel, Record, Alarm, Network and System settings, as shown in figure 5-1.

Channel

• Channel settings contain Camera, Encode, Image, OSD, Privacy Zone, ROI (region of interest), Microphone, Human thermometer, Smart, and Intelligent tracking.
• Camera: Users can add cameras automatically by clicking Click to Add, and add manually by clicking Add. Tick cameras then click Delete to delete cameras. Users can batch update software.
• Encode: Users can set stream, encode type, resolution, frame rate, bit rate type, bit rate and so on.
• Sensor setting: Adjust image parameters and users can set senor parameter.
• OSD: Customize time and channel name displaying in the live video page.
• Privacy Zone: Set a privacy zone by clicking ana dragging cursor and double-click an exist private area to delete it. Support up to 4 zones.
• Some of these settings can be copied to other channels by clicking Copy button.
• Microphone, Human Thermometer, Smart, and Intelligent Tracking are the special functions for some models, not applicable for all cameras.

Record

• Record settings contain Record Schedule, Disk, Storage, RAID,
• S.M.A.R.T, Disk Detection, Disk Calculation and FTP.
• Record Schedule: Set record schedule and storage strategic.
• ANR is auto network recording, if the camera is plugged SD card and enabled record, if camera is disconnected, when the connection is recovered, NVR will copy the recording of the lost videos.
• Enter S.M.A.R.T interface to view the state of disks. Disk detection can detect the disks.
• RAID: If users install more than four disks and want to keep the data safety, it is recommended to build RAID.
• Disk Detection: Check the disk health status.
• Disk Calculation: Two methods to calculate.
• FTP: File Transfer Protocol, set the FTP path to save the alarm information if linkage to FTP.

NOTE

• Format the disk and all data on disk will be lost, please be careful to do this.
• Before replacing the hard disk, the power must be turned off.
• The disks of building RAID should be enterprise level, and the capacities are better at the same.
• For the safety of disks, please make sure the stabilization of power on.

Alarm
Alarm settings contain General, Motion Detection, Video Loss, Advanced Intelligent Analysis, Intelligent Analysis, Alarm in, Abnormal Alarm, Alarm out, ADAM and Local intelligent analysis, as shown in figure 5-2.

• General: Enable or disable alarm and set duration time of alarm and buzzer.
• Motion Detection: Enable this function, if detects any movement, it will alarm.
• Event actions: Contain buzzer, alarm out, push message to App, pop-up message to monitor, send E-mail and post recording (after enabling, choose the recording time from drop list.)
• Area: Set motion detection area. Press left button and drag the cursor to add a detection area, and double-click an area to delete it.
• Schedule: Set schedule to enable or disable motion detection alarm. There are three methods to set: the first is clicking the double arrows button to choose all day. The second, click and drag the cursor to select periods. The third, click one by one.
• Video Loss , Intelligent Analysis are same settings as motion detection. Advanced Intelligent Analysis is used for thermal cameras, alarms for smoker detection, smoke and flame detection and fire spot detection.
• Alarm In / Alarm out: Settings for I/O alarming. Abnormal Alarm can tick disk error, IP conflict, network disconnected, etc.
• ADAM: Add the ADAM data acquisition modules to allow connecting to more alarm devices.
• Local Intelligent Analysis: It is up to be set for 4 channels, set local intrusion parameter on NVR.

Network

Network settings contain Network, 802.1X, DDNS, Port Mapping, E-mail, P2P, IP Filter, SNMP, 3G/4G, PPPoE, Network Traffic and Platform Access, as shown in figure 5-3.

• Network, 802.1X, DDNS, and SNMP interface to set network parameters.
• Email: Set E-mails for sending and receiving alarm messages and password retrieval message.
• Port Mapping: Set the ports for remote scanning.
• P2P: Add NVR into device list of App by accessing the QR code.
• IP Filter: Settings for creating black list or white list.
• 3G/4G: Use 3G/4G modem plug to NVR provide the network.
• PPPoE: Point to point network to access NVR directly.
• Network Traffic: View the send and receive rate of network.
• Platform Access: Set URL parameters for accessing to CMS(Center Management System).

System

System settings contain Information, General, User Account, Security Center , Layout, Auxiliary Screen, Logs, Maintenance and Auto Reboot, as shown in figure 5-4.

• Information: View the basic information, such as System, Network, Channels, Disk, Alarm.
• General: Include system, date and time, time zone, DST.
• User Account: Add users and set advance setting (auto login, password double authentication, boot wizard).
• Security Center: Modify the password, pattern unlock, secure Email, Secure question.
• Layout: Add layouts to preview live video of the channels.
• Auxiliary Screen: Use HDMI and VGA to view live video at the same time. HDMI port output acts as main screen.
• Logs: Users can export logs ( operating and alarm logs) if plug in a USB disk.
• Maintenance: Include shutdown, reboot, exit system, reset, import configuration, export configuration and update.
• Auto Reboot: Enable this function and the device will restart periodically.

Live Video

Enter the user name and password in the login interface, and click Login to enter the real-time video interface. As shown in Figures 5- 5.

Mobile Client

• Search for “InView Pro4” in App Store or Google Play to download and install the App.
• Use the App to scan the QR code, which you can find it on the backboard of the NVR and on P2P settings page (Main menu>Network>P2P) in user interface.
• Then input the NVR’s user name and password to add the NVR to the device list.
• Users can manage the device on the APP.

Web Accessing

The NVR also can be accessed in a Web browser. Open a web browser like Chrome 45 and enter the IP address of device (The default IP address is 192.168.0.121) in the address box, and press Enter. The login page is displayed as shown in figure 7-1.

NOTE

• The user name and password are the same as the UI interface.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>