BOSCH GCT30-42 Auto Start Dust Vacuum Remote User Manual

June 1, 2024
Bosch

BOSCH GCT30-42 Auto Start Dust Vacuum Remote

BOSCH-GCT30-42-Auto-Start-Dust-Vacuum-Remote-product

Specifications

  • Model: GCT30-42
  • Manufacturer: Bosch
  • Battery Type: Button/coin cell 3V lithium CR2032
  • Compliance: FCC Part 15, FCC Part 2.1093

Product Usage Instructions

Safety Instructions It is crucial to follow these safety instructions to ensure safe operation of the product:

  1. Read and understand all safety warnings, instructions, and specifications provided with the power tool.

  2. Only use the specified Button/coin cell 3V lithium CR2032
    battery listed in the manual. Do not use any other type of battery.

  3. Properly secure the battery compartment cover to prevent accidents.

  4. Avoid disposing of batteries in fire or exposing them to high heat.

  5. Do not attempt to recharge the batteries or short circuit them.

Battery Replacement When replacing the battery, follow these steps:

  1. Ensure the product is turned off before replacing the battery.
  2. Use only the recommended Button/coin cell 3V lithium CR2032 battery.
  3. Carefully remove the old battery and insert the new one in the correct orientation.
  4. Securely close the battery compartment cover.

Maintenance Regular maintenance helps prolong the product’s lifespan:

  1. Clean the product regularly with a soft, dry cloth.
  2. Avoid exposing the product to water or moisture.
  3. Store the product in a cool, dry place when not in use.

FAQs

Q: What should I do if the battery compartment cover does not close securely?A: If the cover does not close securely, stop using the product, remove the battery, and keep it away from children. Contact customer support for assistance.

Q: Can I use a different type of battery with the product? A: No, only use the specified Button/coin cell 3V lithium CR2032 battery mentioned in the manual to prevent safety hazards.

Q: How often should I replace the battery? A: Replace the battery as needed or when it no longer functions effectively. Follow the instructions in the manual for proper battery replacement.

Safety Symbols

The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to these symbols.

  • This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.

Danger

DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury

Warning

WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.

Caution

CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

General Power Tool Safety Warnings

WARNING

Read all safety warnings, in- structions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE

WARNING

Only use batteries listed in this operating manual. Only use Button/coin cell 3V lithium CR2032 battery. Do not use any other button/coin cells or other forms of electri- cal power supply.

WARNING

Ensure that battery replace- ment is carried out properly. There is a risk of explosion.

WARNING

Chemical Burn Hazard. Keep batteries away from children. This product contains a lithium button/coin cell battery. If a new or used lithium button/coin cell battery is swal- lowed or enters the body, it can cause severe internal burns and can lead to death in as little as 2 hours. If you think a battery might have been swallowed or placed in- side any part of the body, seek immediate medical at- tention.

WARNING

Always completely secure the battery compartment cover. If the battery compartment cover does not close securely, stop using the product, remove the battery, and keep it away from children.

WARNING

When discarding batteries, in- sulate the ‘+’ and ‘-‘ terminals with insulating tape. When disposed of improperly, lithium batteries may short, causing them to become hot, burst or ignite.

WARNING

Never dispose of the batteries in a fire or expose to high heat. The batteries may explode.

WARNING

Do not attempt to recharge the batteries and do not short cir- cuit the batteries. The batteries may leak, explode, catch fire and cause personal injury.

WARNING

Follow all instructions and warnings provided by your Bluetooth® device manufacturer. Failure to follow rec- ommended procedures could result in personal injury or property damage.

FCC Statement

The GCT30-42 complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The GCT30-42 complies with the safety requirements for RF exposure in accordance with FCC Part 2.1093 for portable use conditions. Product Name / Model Number: Auto-Start Remote Receiver/GCT30-42

FCC Caution

The manufacturer is not responsible for radio interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. This device must accept any interference received, \including interference that may cause undesired operation.

NOTE! This equipment has been tested and found to comply with the limits for a Class B digital devices, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Industry Canada

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

  1. this device may not cause interference, and
  2. this device must accept any interference, including interference that may cause undesired operation of the device.

This equipment complies with ISED RSS-102 radiation exposure limits set forth for an uncontrolled environment. The equipment complies with the safety requirements for RF exposure in accordance with RSS-102 Issue 5 section 2.5.1 for portable (≤20 cm) use conditions. HVIN: GCT30-42

Intended Use

This Auto-Start remote is compatible with the GCA30-42 receiver and with cordless dust extractors with Auto- Start mode. It is designed to automatically start and stop the dust extractor when the cordless power tool is turned on/off. When the cordless power tool is turned on/off, the vibration detection sensor inside the GCT30-42 Auto-Start Remote generates a start-stop signal for the dust extractor.

Specifications

BOSCH-GCT30-42-Auto-Start-Dust-Vacuum-Remote-fig \(2\)

A) Without attachment band

Values can vary depending upon the product and are subject to application and environmental conditions. For further information www.bosch- professional.com/wac

Getting to Know Your Product

BOSCH-GCT30-42-Auto-Start-Dust-Vacuum-
Remote-fig \(3\)

  1. Auto-Start Remote
  2. LED Status Indicator (User Interface)
  3. Start/Stop Button (User Interface)
  4. Fastening Hook for Attachment Band
  5. Battery Compartment Cover
  6. Attachment Band
  7. CR2032 3V Li-ion Cell Battery
    Included in the GCT30-42

Assembly

Mounting the Auto-Start Remote

To mount the Auto-Start Remote:

  1. Attach one end of the Attachment Band 6 to one of\ the two Fastening Hooks 4 (Fig. 2).
  2. Secure the Auto-Start Remote 1 to the cordless tool.

To do so, tighten the Attachment Band 6 and attach the free end to the second Fastening Hook 4 (Fig. 3). If needed, cut the attachment band to the correct length. When attaching the Auto-Start Remote to the cordless tool, ensure it is placed in an area that generates sufficient vibration during operation. Never attach the Auto-Start Remote to places that are required to operate the cordless tool (for example, gripping surfaces, switches, etc).

Operation

Establishing Connection

  • Connect the Auto-Start Remote 1 to the receiver GCA30-42 or to the appropriate Bosch dust extractor.
  • Read the Operating Instructions and Establishing Connection sections in the operating instructions for the Auto-Start System GCA30-42K or the dust extractor that is being used.

Battery Replacement

When changing the coin cell, the following shall apply:

  • If the Auto-Start Remote 1 was connected to the receiver GCA30-42 before changing the coin cell, the connection is automatically reestablished after changing the coin cell.
  • If the modules were not connected before replacing the coin cell, the connection will need to be established. After a reset, the Auto-Start Remote 1 and the receiver must be reconnected.

BOSCH-GCT30-42-Auto-Start-Dust-Vacuum-Remote-fig \(6\)

Resetting to Factory Settings

Auto-Start Remote GCT30-42: Press and hold the Start/Stop Button 3 until the LED Status Indicator 2 flashes blue four times in rapid succession.

Vibration Detection

The GCT30-42 transmitter module is equipped with vibration detection. Once the utilized cordless tool is activated, the GCT30-42 transmitter module detects the vibrations of the activated cordless tool and automatically switches on the dust extractor.

  • If the cordless tool is switched off, the dust extractor will switch off automatically.

Auto Starting/Stopping the Dust Extractor
When paired with the GCA30-42 receiver:

  • Once the plug of the dust extractor has been inserted into the primary power source, the switch of the dust extractor has been set to Power Tool Activation Mode, the plug of the receiver GCA30-42 has been inserted into the plug socket of the dust extractor and both the Auto-Start Remote 1 and receiver GCA30-42 have been successfully paired, your auto start system is ready to be used.
  • Ensure that the Auto-Start Remote 1 is flush and snug against the mounting surface of the cordless tool by adjusting the position on the supplied attachment band 6.
  • Insert the extraction hose into the dust extractor attachment of the cordless tool.
  • Once the cordless power tool is turned on/off, a start/ stop signal is sent from the Auto-Start Remote 1 to the receiver GCA30-42 and the corresponding dust extractor is turned on/off. When paired with the cordless dust extractor with Auto- Start mode:
  • Ensure that the cordless dust extractor has been set to the Auto-Start mode and the Auto-Start Remote 1 has been successfully paired with the cordless dust extractor.
  • Once pairing between the cordless dust extractor and the Auto-Start Remote 1 was successful, ensure that the Auto-Start Remote 1 is flush and snug against the mounting surface of the cordless tool by adjusting the position on the supplied attachment band.
  • Insert the extraction hose into the dust extractor attachment of the cordless tool.
  • Once the cordless power tool is turned on/off, a start/ stop signal is sent from the Auto-Start Remote 1 to the cordless dust extractor and the dust extractor is turned on/off.

Utilizing Manual Mode

  • Briefly press the Start/Stop Button 3 on the Auto-Start Remote 1. The dust extractor will be switched on.
  • To manually switch the dust extractor off, press the Start/Stop Button 3 on the Auto-Start Remote 1 again.

Note: If the dust extractor is switched off using the Start/ Stop Button 3 on the Auto-Start Remote 1, the dust extractor will automatically switch on once the Auto-Start Remote 1 detects the vibrations of the activated cordless tool.

Maintenance

Remove any visible dirt and debris using a brush or a damp cloth. Do not use any detergents or solvents

Coin Cell Replacement

Warning

The coin cell must always be replaced with a coin cell of the same type. There is a risk of explosion if any other coin cell type is utilized than what is recommended.

Removal of the Coin Cell.

Warning

The drained coin cell may leak and damage the product or cause personal injury.

  1. Open the Battery Compartment Cover 5 on the rear of the Auto-Start Remote 1 with a coin or small flat head screwdriver by turning counterclockwise (Fig. 4). Once the battery compartment cover is loose, remove the battery compartment cover from the Auto-Start remote.
  2. Carefully remove the older coin cell and insert the new coin cell into the Auto-Start Remote 1 (Fig. 4). To ensure the new coin cell is correctly inserted, follow the markings on the Auto-Start Remote carefully.
  3. Once the new coin cell has been inserted correctly, reinstall the Battery Compartment Cover 5 onto the rear of the Auto-Start Remote 1 and turn the battery compartment cover clockwise utilizing a coin or a small flat head screwdriver until it can go no further (Fig. 4). This will ensure that the Battery Compartment Cover is properly secureBOSCH-GCT30-42-Auto-Start-Dust-Vacuum-Remote-fig \(8\)

LIMITED WARRANTY

For details on the terms of the limited warranty for this product, go to https://rb-pt.io/PowerToolWarranty or call 1-877-BOSCH99.

Robert Bosch Tool Corporation 1800 W. Central Road Mt. Prospect, IL 60056-2230

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals