PROTECTOR WA-5.1 External Sensor with Socket Instruction Manual
- June 1, 2024
- Protector
Table of Contents
PROTECTOR WA-5.1 External Sensor with Socket
Product Overview
Thank you for purchasing the WA-5.1 water detector.
Please read these operating instructions through carefully before initial
operation of the device and retain them for any later use.
This water detector is used to switch connected devices (to a maximum of 3600 watts) ON or OFF as soon as the sensor comes into contact with water. Once the water detector has detected water an alarm also sounds.
This water detector is only authorised for indoor use and may not be arranged successively
Scope of delivery
1x Water detector including 2 m sensor cable and sensor
2x Ring cable lugs
1x Attachment material
1x Instructions
LEGEND
- = Water detector
- = ALARM LED
- = RESET button
- = Loudspeaker for alarm
- = Power LED
- = Sensor cable (2m)
- = Sensor casing screw
- = Sensor
- = Sensor electrode
- = Alarm volume switch
- = Function selector switch
- = Electrode screws
- = Attachment hole
- = Ring cable lug
- = STATUS LED outlet
OPERATION
Insert a water detector into a suitable 230V mains socket and connect any device you wish to protect into the socket on the water detector. Use the slider on the side (11) to select whether a connected device should be switched ON or OFF. Depending on the switch position, the WA-5.1 behaves as follows:
Switch position ON (EIN)
As soon as the sensor detects water, the alarm sounds and the socket switches ON. This status is maintained as long as water is present at the sensor. If the sensor detects no more water, the alarm stops after approx. 2 minutes and the socket switches back. The alarm LED continues to flash until the reset button (3) is pressed.
Switch position OFF (AUS)
As soon as the water detector detects water an alarm will sound for approx. 2 minutes and the socket will switch OFF. The alarm LED and the socket can only be cancelled using the RESET button. To do this press the button briefly once after the sensor is dry again. Then the device can detect water again.
The STATUS LED (15) shows whether the socket on the water detector is conducting electricity (LED lights up) or is switched off (LED not lit).
You should check the water detector for function at regular intervals. To do this submerge the sensor electrodes (9) briefly in tap water. If no alarm sounds see the section ‘malfunction’.
MOUNTING
The sensor can be opened by removing the screw (7). There is a small hole (13) on the back of the sensor so that the sensor can be mounted at its location using a small screw. You should select the mounting location in such a way that any water can be detected as quickly as possible. The two sensor electrodes (9) should be just above the floor.
Adjusting the sensor cable (figures 2 + 3)
NOTE: disconnect the water detector from the socket before shortening the cable.
If the sensor cable is too long then you can shorten the cable as necessary.
To do this you will need the supplied ring cable lug, a small Philips
screwdriver and pliers (e.g. combination pliers).
First remove the casing screw (7) using the screwdriver and remove the lid
from the sensor. The two electrode screws are now exposed and you can remove
these also. Caution, the electrodes are then also released.
Use the pliers to shorten the cable and ensure that you do not cut too much off. Remove the outer insulation at the point of cutting to a length of approx. 15 mm and the insulation on the wires to approx. 5 mm, measured from the cut point. Push a ring cable lug onto one of the two exposed wires and then pinch the back of the ring cable lug together using the pliers. Alternatively the wires can also be soldered to the cable lugs.
SETTINGS
Function selector switch (11)
Use this selector switch to set whether a connected device is to be switched ON or OFF. Slide the switch to the OFF setting (crossed out socket) in order to switch a connected device off if the sensor electrodes (9) come into contact with water. The water detector switches the connected device on when the selector is set to ON.
Alarm volume switch (10)
Use this switch to set the volume of the alarm to one of 3 levels. MAX is the highest setting and MIN is the lowest setting.
RESET button (3)
Press the RESET button briefly in order to cancel the alarm after water has been detected.
MALFUNCTION
Alarm cannot be switched off using the RESET button
If it is not possible to deactivate the alarm using this button then it is still detecting water. This can happen, for example, if water has penetrated the sensor. In this event remove the water detector from the socket and allow the sensor to dry. You can also dismantle the sensor and then dry it with a dry cloth.
No alarm although both sensor electrodes are submerged in water
- Sensor electrodes have no contact to the sensor cable > check the pinch on the ring cable lug.
- Sensor electrodes are contaminated > clean the sensor electrodes, e.g. with fine sandpaper or a glass fibre eraser.
- If points 1 and 2 do not help then there may be a defect. In this event please contact our service. The contact details can be found on www.protector24.de
NOTES
The functionality of the unit can be affected by the influence of strong static, electrical or high frequency fields (discharging, mobile phones, radios, microwaves).
Cleaning and maintenance
Always disconnect mains powered units from the mains supply before cleaning
(disconnect the plug).
The unit housing can be cleaned using a soapy soft cloth. Do not use any
abrasive materials or chemicals. Remove dust build-up from ventilation slits
using a brush and clean up using a vacuum cleaner. Do not hold the vacuum
cleaner nozzle directly against the unit.
SAFETY NOTES
The warranty will be null and void in case of damages arising from violations of these operating instructions. We are not liable for consequential damages!
We accept no liability for material damages or injuries arising from inappropriate use or violation of the safety instructions. In such cases all warranty claims are null and void! For reasons of safety and licensing (CE), unauthorised conversion and /or modification of the product is prohibited.
The design of the product complies with protection class 1. Only a standard mains socket (230V /50Hz) of the public mains supply may be ~ used to power the device. Devices powered by mains voltage must be kept away from children. Please therefore be particularly careful in the presence of children.
Do not take the product apart! There is a danger of lethal electric shock!
Do not leave packaging material lying about since plastic foils and pockets and polystyrene parts etc. could be lethal toys for children.
The device is suitable only for dry interior rooms (not bathrooms and other moist places). Do not allow the device to get moist or wet. There is a danger of lethal electric shock!
Please consult a specialist should you have doubts regarding the method of
operation, the safety, or the connections of the device.
Handle the product with care – it is sensitive to bumps, knocks or falls even
from low heights.
2 YEAR LIMITED GUARANTEE
For two years after the date of purchase, the defectfree condition of the
product model and its materials
is guaranteed. This guarantee is only valid when the device is used as
intended and is subject to regular maintenance checks. The scope of this
guarantee is limited to the repair or reinstallation of any part of the
device, and is only valid if no unauthorised modifications or attempted
repairs have been undertaken. Customer statutory rights are not affected by
this guarantee.
Please note!
No claim can be made under guarantee in the following circumstances:
- Operational malfunction
- Unauthorised modifications / actions
- Mechanical damage
- Moisture damage
- No proof of guarantee (purchase receipt)
Claims under warranty will be invalidated in the event of damage caused by non-compliance with the operating instructions. We do not accept any responsibility for consequential damage! No liability will be accepted for material damage or personal injury caused by inappropriate operation or failure to observe the safety instructions. In such cases, the guarantee will be rendered void.
Liability limitation
The manufacturer is not liable for loss or damage of any kind including incidental or consequential damage which is the direct or indirect result of a fault to this product.
GB
These operating instruction are published by Protector GmbH, An den Kolonaten 37, 26160 Bad Zwischenahn/Germany The operating instructions reflect the current technical specifications at time of print. We reserve the right to change the technical or physical specifications.
Customer Support
Protector GmbH hereby declares that this device
complies with the following guidelines:
RoHS 2011/65/EU LVD
2014/35/EU
EMC 2014/30/EU
The DECLARATION OF CONFORMITY can be obtained at the following address
can be accessed:
http://www.protector24.de/download/ce/WA-5.1ce.pdf
PROTECTOR GMBH
AN DEN KOLONATEN 37
D-26160 BAD ZWISCHENAHN
GERMANY
WWW.PROTECTOR24.DE
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>