BOSCH SMV2HTX02G Fully Integrated Dishwasher Instruction Manual

June 1, 2024
Bosch

BOSCH SMV2HTX02G Fully Integrated Dishwasher

Specifications:

  • Water Hardness Range: Soft (0 – 1.1 mmol/l), Medium (1.2 – 2.9 mmol/l), Hard (3.0 – 3.7 mmol/l), Very Hard (3.8 – 8.9 mmol/l)
  • Programme Durations: Vary based on programme selected
  • Energy Consumption: Varies based on programme
  • Water Consumption: Varies based on programme

Product Usage Instructions

Setting up Home Connect:

  1. Install the Home Connect app on your mobile device.
  2. Scan the QR code with the Home Connect app.

Setting the Water Softening System:

  1. Press the designated button to access appliance settings.
  2. Select the appropriate water hardness setting (0, 1, 2, or 3 LEDs will light up).
  3. Save the settings by pressing the button for 3 seconds.

Adding Special Salt:

  1. Unscrew the lid of the special salt dispenser and remove it.
  2. Fill the dispenser with water initially.
  3. Add special salt to the dispenser.
  4. Close the lid securely after adding salt.

Frequently Asked Questions

Q: When should I add rinse aid?

A: Add rinse aid up to the max mark in the dispenser before starting a programme.

Q: How do I cancel a programme?

A: To cancel a programme, press the designated button for approximately 4 seconds.

Before using for the first time, read the instruction manual and the safety information it contains.

Setting up Home Connect

Tip: Connect your appliance to a mobile device. You can con-veniently change all settings using the Home Connect app.

  1. Install the Home Connect app on your mobile device and fol-low the instructions.
  2. Scan the QR code with the Home Connect app.

Overview of water hardness settings

You can find an overview of the water hardness values that can be selected here.
A table of country-specific units can be found in the instruction manual.

Setting the water softening system

  1. Press ⁠ .

  2. To open the appliance settings, press for 3 seconds.
     flashes.

  3. Press Start repeatedly until the right water hardness has been set. 0, 1, 2 or 3 LEDs will light up ac- cordingly.

  4. To save the settings, press Setup 3 sec. for 3 seconds.

Programmes

  • The programme data has been meas-ured in the laboratory according to European standard EN 60436.
  • The consumption figures depend on the programme and additional func-tion selected.
  • The running time will change if the rinse aid system is switched off or rinse aid needs to be added.

How to use your appliance

  1. Load the tableware.
    Only clean tableware that is suitable for dishwashers. Remove large remnants of food from the tableware. Check that the spray arms can rotate freely.

  2. Add detergent.

  3. Switch on the appliance ⁠.

  4. Select the programme.

  5. Start the programme Start.

  6. Remove the tableware at the end of the programme.

  7. To cancel the programme, press Reset 4 sec. for approx. 4 seconds.
    The programme is cancelled and ends after ap-prox. 1 minute.

Cleaning filters

  1. After each wash check the filters for residue.

  2. Turn the coarse filter anticlock-wise and re-move the filter system ⁠.

  3. Pull down the micro filter to re-move.

  4. Press the locking catches to-gether and lift the coarse filter out ⁠.

  5. Clean the filter elements under running water.

  6. Re-assemble the filter system.

  7. Insert the filter system into the appliance and turn the coarse filter clockwise. Make sure that the arrow markings match up.

Cleaning spray arms

  1. Unscrew the upper spray arm and pull down to remove ⁠.

  2. Pull up the lower spray arm to remove.

  3. Check the outlet nozzles on the spray arms for blockages un-der running water and remove any foreign bodies.

  4. Insert the lower spray arm.
    aThe spray arm clicks into position.

  5. Insert the upper spray arm and screw it firmly in place.

Clean wastewater pump

  1. Disconnect the appliance from the power supply.

  2. Remove the filter system.

  3. Scoop out any water.

  4. Prise off the pump cover using a spoon and grip it by the crosspiece.

  5. Lift the pump cover inwards at an angle and remove.

  6. Remove any remnants of food and foreign bodies in the area of the impeller.

  7. Insert the pump cover 1 and press down 2
    The pump cover clicks into position.

  8. Install the filter system

Troubleshooting

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals