QAZQA 92642 Fresh Fan Instruction Manual

QAZQA 92642 Fresh Fan Instruction Manual

www.qazqa.nl

Warning Symbols

General Safety Instructions

Read this instruction manual thoroughly before using the appliance and save it for future reference and if necessary pass the instruction manual on to a third party.

WARNING : When using electrical appliance, basic safety precautions should always be followed to reduce the risk of fire, electrical shock and personal injury.

1) General

• Before carrying out any work on the fan, disconnect it from the electrical supply!

• Check if the electrical specifications of this appliance are compatible with your installation. The supplier accepts no responsibility for any physical injury or material damage resulting from incorrect use or installation of this fan.
  If you have the slightest doubt, please contact electrician.

• Unauthorized use and technical modifications to the appliance can lead to danger to life and health.

• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision

• Children should be supervised to ensure that they do not play with the appliance.

• This appliance is for indoor use only.

• Means for disconnection must be incorporated in the fixed wiring in accordance with the wiring rules.

• Never install the appliance in a moist or wet room.

• Be careful when working near the rotating blades. The fan should be installed at least a height of 2.3m

• Before pushing the reversible slide switch, it is necessary to stop the action of the blades by turning off the fan

• Don’t place your arm or other object in the path of the blades, when the fan is operating.
  Always maintain the minimum distance between the lamp and any inflammable material (curtains, wall etc), as indicated on the pictogram

• Means for all poles disconnection having a contact separation that provide full disconnection under over voltage category Ill conditions must be incorporated in the fixed wiring in accordance with national wiring rules.

• Power supply wire from ceiling needs 1.5 sq mm wire

• Regarding the method of the cable connection , assembly steps and the bulb type of the luminaire, please refer to the section “INSTALLATION”

• Warning: Before obtaining access to terminals, all supply circuits must be disconnected.

2) Electrical Safety

The appliance should be installed by authorized electrician only acc. to national wiring rules.

3) Specific Safety Rules
The fan is to be installed so that the blades are more than 2.3 m above the floor

3. Environmental Protection

CAUTION!

Electrical products must not be thrown out with domestic waste. They must be taken to a communal collecting point for environmentally friendly disposal in accordance with local regulations. Contact your local authorities or stockist for advice on recycling. The packaging material is recyclable. Dispose of the packaging in an environmentally friendly manner and make it available for the recyclable material collection-service.

Appliance Specifications

The Ceiling Fan (element)

PARTS DESCRIPTION

1. MOUNTING PLATE
2. J HOOK (FOR TEMPORARILY HANG UP THE FAN WHEN WIRING CONNECTION)
3. SCREWS
4. SCREWS
5. HANGER BALL
6. UPPER CANOPY
7. DOWNROD
8. COTTER PIN
9. CROSS PIN
10. SCREWS
11. DOWNROD YOKE
12. MOTOR
13. BLADE HOLDERS
14. BLADE
15. BLADE HOLDER SCREWS
16. LAMP HOLDER
17. LIGHT PLATE
18. PULL CHAIN
19. LIGHT BULB(Not provided)
20. GLOBE
21. BLADE SCREWS

Installation Of the Ceiling Fan

1. Install the mounting plate by screw (Fig.1)

2. Insert down rod over upper canopy (Fig 2 3)

3. Then, insert the cross pin over yoke and Cotter pin(Fig 4)

4. Connect the wire as the fig show (Fig 5)

5. Make sure the wiring correct, if you are not sure, pis consult qualified electrician (Fig.6)

6. Hang up the fan and assemble the mounting plate with the motor set by 4 side screws (Fig 7)

7. Assemble the blades to blade holders (Fig 8)

8. Loose the screw before install the blade (Fig 9)

9. Tighted up the screws after install the blade.(Fig 10)

10. Install the light bulb (not provided), .(Fig 11 )

11. Install the glass (Fig 12)

12. Now, the fan is completed (Fig 13)

Warnings:

Do not poke any objects or fingers through the protective screens
Do not place any objects,such as clothing, on the device
Be careful with long hair. These can be sucked in by the air flow, keep sufficient distance.

How To Use

Disconnect From Mains Before Maintenance Or Cleaning.

Do not use a wet sponge to clean the appliance.

1. Before conducting any cleaning or maintenance work, disconnect the lamp from the electrical supply and wait until it cools down
2. No abrasive products, solvents, detergent or any other liquid may be used to clean the fan or lamp
3. Be sure the power is off when you clean the fan
4. Don’t clean the motor, switch house and other electric parts of the fan with water in order to avoid short circuit

Trouble Shooting

PREFACE

Your ceiling Ian may sometimes have wobble problem when operate due to irregularity in blades or the blade holder. Also, improper assembly in the mounting system may cause some additional problem also bearing crooked. The following procedure to remedy such problem is strongly recommended by us from our past experience in handling the wobble problem.

Dynamic blade balancing kit for ceiling fans

1. Make sure that all blade are firmly screwed into the blade holder
2. Make sure that all blades are firmly secured with the flywheel and pitches of blade holders are the same
3. By looking up the Ian from below, check and be certain that none of the blade holders are bent so that none of the blade is out of position. A correction can be made by very gently bending the blade holder back into position
4. By the simple use of a household yardstick blade tracking can be checked, out the yardstick up against the ceiling vertically and even with the outside leading edge of a blade. Note the distance of the edges of the blade to I he ceiling; carefully turn the blade slowly by hand to check the remaining blades. If blade is not in alignment, the blade holder may be gently bent up or down to be in line with the other blades

I by following all the steps and the wobble problem is not solved, a dynamic balancing need to be done by the use of the balancing kit. Follow the procedure listed below:

• Turn the Ian on and adjust the speed control (usually high speed) setting to the speed, which creates to greatest wobble.

• Turn the Ian off; select on blade place the balance clip on it. Halfway between the blade holder and the blade up on the rear edge of the blade.

• Turn the Ian on, watch to see M the wobble is improved or worse. Then, turn the Ian off again and move the clip to another blade and test again.
  Repeat this process with all blades and then note that which blade is the most improved.

• Move the clip back to the blade, which showed the most improvement. Move the clip inward and outward on this blade and operate t he Ian to find the position where the clip gives the most improvement

• Next remove the clip and install a balancing weight to the top of the blade along the centerline near the point where the clip was positioned.

Caution: stay clear of the blades ii the clip for any reason is not secured, injury could result

Others

Have your product repaired by a qualified person
This electric product is in accordance with the relevant safety requirements. Repairs should only be carried out by qualified persons using original spare parts; otherwise this may result in considerable danger to the user. This appliance can be used by children aged from 8 years and above ii they have been given supervision or instruction concerning use of the appliance in a sale way and ii they understand the hazards involved. Cleaning and user maintenance shall not be made by children unless they are older than 8 and supervised. Keep the appliance and its cord out of reach of children aged less than 8 years.
Please contact the store where you bought the product for alter sale services if question

This appliance can be used by children aged from 8 years and above if they have been given supervision or instruction concerning use of the appliance in a safe way and if they understand the hazards involved. Cleaning and user maintenance shall not be made by children unless they are older than 8 and supervised. Keep the appliance and its cord out of reach of children aged less than 8 years.

Appliances can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance.
Please contact the store which you bought the product for after sale services if question

SAFETY INSTRUCTION

Please study the instruction manual and below information carefully before installing or using this product.
Please keep this user manual for further reference

1. The luminaires may only be installed by authorized and qualified technicians according the valid regulations for electrical installation.

2. Maintenance of the luminaires is limited to their surfaces. During maintenance no moisture can come
   into contact with any areas of the terminal connections or voltage control parts.

3. The electrical supply must be switched off at the outset, preferably by means of a switch in the distribution box, before any installation, maintenance or repair work is undertaken.

4. Exterior lighting must not be installed during rain.

5. Take account of the minimal separation distance from other objects and the room required around the fitting.

6. If in any doubt, consult a professional, taking local installation requirements into account. Some countries stipulate that lighting may be installed only by registered installers.

7. Clamping screws in electrical connections must be adequately tightened. This is particularly the case with 12V low voltage conductors.

8. Clean with a clean, dry cloth or brush, use no solvents or abrasives. Avoid dampness on all electrical components

9. Take account of all available technical information.

10. Meaning of symbols:

This luminaire cannot be disposed together with normal domestic waste in standard rubbish can, but you have to bring it to a staging area for electrical waste
1.Take note of the symbols when connecting wires:

F1tt,nQ B. V.
Smaragdweg 52, 5527 LB Ha pert, The Netherlands
www.qazqa.nl

F1ttmQ LTD

55 Baker Street,
London, Wl U 7EU
United Kingdom

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>