heaflex B0BM6J4JZ2 Dog Shock Collar with Remote User Guide

heaflex B0BM6J4JZ2 Dog Shock Collar with Remote

Package content

Product Overview

Key Definition

1. Antenna: transmit the signal strongly.
2. LCD screen : Show the modes, levels and channels.
3. Shock button: Press to choose Shock mode, the screen show@, press+ or – button to adjust the levels from O — 16, press Shock button again to make the Receiver shock.
4. Vibration button: Press to choose Vibration mode, the screen show@, press+ or- button to adjust the levels from O — 16, press Shock button again to make the Receiver vibrate.
5. Sound button: Press to choose Sound mode, the screen show@, don’t need to adjust the levels, just press to make the receiver sound Bee–.
6. +button: press+ to increase the training levels.
7. – button: press – to reduce the training levels.
8. Channel button: choose your training channel between CH1/CH2/CH3 by press this button.
9. Power button of the Remote : press to turn on the Remote, press again to turn it off.
10. Lock button: Press to lock the Remote, all button of the Remote is unavailable; Press again to unlock it.
11. Magnetic charging point of the Remote.
12. Shock static electrode: Conduct the safe static; To install the rubber cap, reach to pet’s skin.
13. Power button of the Receiver.
14. Indicator light of the receiver: the light will be on when press the shock/vibration/sound button; When charging, it flash.
15. Magnetic charging point of the Receiver.

Charging prior to use

Notes

1. The battery icon on the display will flash while the Remote control is charging . The battery icon will stop flashing and reflect a full status when completely charged. The battery icon on the display will indicate a space status if the Remote control runs out of power.
2. The Receiver’s LED status light will light up and flash in a breathing light while charging; After completely charged, the LED status light will cease flashing and remain on. When the Receiver is charging, it goes in to sleep mode, which means it can’t receive signals and can’t be controlled by the Remote control. The LED status light will blink every second when the Receiver is low.
3. Make sure the charging port is dry before charging the Receiver.

Product switching on/off

1. Turn on the Remote control by pressing power button.
2. If there is no additional operation, the LED display will switch off after 30 seconds and can be switched back on by pressing any button on the Remote control.

1. Press the Receiver’s power switch button, the Receiver is switched on, the LED status light will flash once, while the Receiver makes a beep sound; Press the Receiver’s power switch button again, the Receiver is switched off, the LED status light will flash again, while the Receiver makes two beep sound.
2. The LED status light will flash every 7 seconds when the Receiver is switched on, indicating that it is in working condition and ready to receive signals from the Remote control.
3. lf the Receiver does not receive an operational signal for 5 minutes, it will enter standby mode, which may be accessed by pressing the shock button/vibrate button/beep button on the Remote control.

Pairing the Remote control and the Receiver

• You can skip this step as the product is already matched up in the factory. (The paired channel is CH1)

1. Turn on the Remote control and choose a channel by press the CH button;
2. Turn on the Receiver and press the power button of the Receiver by 2 seconds, you hear a beep sound, and the Receiver’s LED status light is flashing;
3. Press the vibrate button/shock button/beep button of the Remote control within 10 seconds after the beep sound, hearing a beep sound again that means the pairing successful.

Pairing additional Receivers

• You can pick a separate pairing channel for pairing an additional Receiver or two, which is done in the same steps as above.

Test training mode

Test the electric shock function

• Connect the test light to the two static electrodes of the Receiver, press the shock button of the Remote control ( ensure the intensity level is more than 0) and the test light will light up.

Test the vibration function
Press the vibrate button of the Remote control (ensure the intensity level is more than 0) and the Receiver will vibrate.

Test training mode

Test the beep function

• The Receiver will beep if you press the beep button of the Remote control (no need to adjust the intensity level for this operation, simply o is display

Wearing the Receiver collar

1. Thread the collar through the Receiver’s collar hole.
2. Thread the collar back through to the buckle and tighten the collar.
3. Place the Receiver collar around the dog’s neck.
4. Tighten as tightly as you can fit through one fingertip.

Frequently Asked Questions (FAQs)

1. When I press the Remote control button, my pet does not react.

2. Ensure the Receiver is turned on.

3. It’s possible that a low battery in the Remote control and Receiver is causing the Remote control distance to be lowered when you first use it.

4. The Remote control distance can be affected by a variety of factors such as topography, weather, vegetation, and the transmission of other radio equipment.

5. Increase the electric shock or vibration’s intensity level.

6. Ensure that the Receiver’s static electrodes are close to the dog’s skin.

7. What should the duration of each dog training session be?
   A: 10-15 minutes.

8. What should I do if the dog training collar doesn’t work?

9. Check the power level of the Remote control and Receiver, then recharge it if it is low.

10. In vibrate or shock mode. Check the intensity level and ensure that the level is over 0.

11. Check if the Receiver is enabled, please press the power switch button to activate it.

12. Check the channel, press the CH button to turn it back on if you have picked another channel.

13. Re-pairing the Remote control and Receiver.

14. The receiver will not respond to the operational signals from the Remote control.

15. Check to see if the Receiver and Remote control are properly paired.

16. 2. Check the Remote control’s display for the channel icon to determine whether it is chosen on the receiver s paired channel.

17. Make sure that the Remote control and Receiver are both switched on. Ii this is not feasible, finish the pairing by going to the “Pairing the Remote control and Receiver” page.

Finding the most appropriate training level for your dog

• Follow these steps to smoothly start training your dog with the tone button
  • Spend 10-15 minutes per day for 2-3 days helping your dog understand the tone.
  •  Associate the tone with reward and praise (some also use the tone as a warning).
  • Push the tone button for 2 seconds.
  • Reward your dog with verbal praise when you release.
  • Allow 2-5 seconds before you repeat the process.

Quick Tip: Vary the rewards while training for the tone function. As soon as your dog starts to anticipate a reward with the tone, you’ve succeeded in this phase.

WARNING

• Do not use this product if your dog is aggressive or exhibits aggressive behaviour frequently. Aggressive dogs can cause serious injury or even death to their owners and others.
• Please follow the manufacturer’s directions while using the product. We are not liable for any damages or injuries resulting from incorrect use.
• It is forbidden to use the product in the presence of open flames or fragile objects.· It is forbidden to use the product in extremely hot (above 40 degrees Celsius) or extremely cold (below O degrees Celsius) environments.
• Do not charge this product with a charger of more than 5 volts.

Product Specification

2 hours

Charging Port| Magnetic point
Wireless Power| mW
Operating Environment| 0-40’t
Remote /Receiver Standby Time| Remote: 120 days

Receiver: 45 days

Remote to Receiver’s Signal Range Distance| BOOM
Frequence| 433MHz

support@heaflex.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>