rmk design RMK-05-GW01S-01 Dry Carbon GT Wing Kit Installation Guide
- June 1, 2024
- rmk design
Table of Contents
rmk design RMK-05-GW01S-01 Dry Carbon GT Wing Kit
Product Information
Specifications:
- Part Number: RMK-05-GW01S-01 RMK-05-GW01S-01M
- Description: Dry Carbon GT Wing Kit for 2022+ Subaru WRX (VB)
- Application: Fits with or without OE trunk spoiler
- Components:
- 1500mm Dry Carbon Air Foil (wing)
- Carbon Fiber End Plates
- Aluminum Stands (uprights)
- Billet Aluminum Base Plate – Right side
- Billet Aluminum Base Plate – Left side
- Foam Pad – Right side
- Foam Pad – Left side
- Flat head M8 x 15mm bolts, color: black
- Countersunk M8 washers, color: black
- Hex Drive M6 x 25mm Button Head Bolts, color: black
- M6 Locking Flange Nuts, color: black
Product Usage Instructions
Required Tools:
We recommend installation by a professional with the assistance of another
person. The following tools are required for installation:
- Center punch
- Drill
- 15/64 drill bit or ~5.9mm
- Tape measure
- Sharpie marker
- Torque wrench (~55 inch/lbs and ~95 inch/lbs)
Installation Procedure:
- Open the trunk and remove the inner liner on the underside of the trunk.
- Lay painter’s tape on the top surface of the trunk in the area where the wing will be mounted.
- Mark the center of the circle on the underside of the trunk where holes will be drilled.
- Use a center punch to mark drilling spots.
- Drill pilot holes for verification before drilling actual holes.
- Place wing assembly on trunk to align holes with base plates.
- Enlarge holes with a 15/64 drill bit or to ~5.9mm.
- Secure wing assembly with M6 hardware and verify hole alignment.
- Drill remaining holes following the same process as above.
- Clean holes from debris and attach foam pads to base mount plates.
- Secure wing assembly with M6 hardware and torque to recommended specifications.
Frequently Asked Questions (FAQ):
Can this wing kit be installed without an OEM trunk spoiler?
Yes, the Dry Carbon GT Wing Kit can be installed with or without an OE trunk spoiler.
What is the recommended torque for securing the wing assembly?
The torque specification for securing the wing assembly is approximately 55 inch/lbs for some components and 95 inch/lbs for others. Please refer to the manual for specific torque values.
Do I need any special tools for installation?
Yes, you will need tools such as a center punch, drill, torque wrench, and measuring tape for the installation process. It is also recommended to have an assistant during installation.
How do I verify the hole alignment between the base plates and the trunk?
You can place the wing assembly on the trunk after drilling pilot holes to ensure alignment. Adjust as needed before drilling final holes and securing with hardware.
PARTS LIST
| ITEM | DESCRIPTION | QTY | NOTES |
|---|---|---|---|
| 1 | 1500mm Dry Carbon Air Foil (wing) | 1 | |
| 2 | Carbon Fiber End Plates | 2 | |
| 3 | Aluminum Stands (uprights) | 2 | |
| 4 | Billet Aluminum Base Plate – Right side | 1 | |
| 5 | Billet Aluminum Base Plate – Left side | 1 | |
| 6 | Foam Pad – Right side | 1 | |
| 7 | Foam Pad – Left side | 1 | |
| 8 | Flat head M8 x 15mm bolts, color: black | 4 | Torque ~55 inch/ lbs. |
| 9 | Countersunk M8 washers, color: black | 4 | |
| 10 | Hex Drive M6 x 25mm Button Head Bolts, color: black | 16 | Torque ~95 inch/ |
lbs.
11| M6 Locking Flange Nuts, color: black| 16|
REQUIRED TOOLS
- Required:
- Hex Drive 5mm for M8 Flat Head Bolts
- Hex Drive 4mm for M6 Button Head Bolts
- Handheld Drill
- 15/64” Drill Bit
- 10mm Box Wrench
- Recommended:
- Painters Tape
- Fine tip sharpie
- Center Punch
- ~1/8” Drill Bit
- Torque Wrench
INSTALLATION PROCEDURE
We recommend installation be performed by a professional. An assistant is recommended. Installation may vary if not being installed on an OEM trunk lid.
-
Clean the top surface of the trunk
-
Assemble the wing, stands, and mounting plates using the M6 bolts and nuts. The angle of the wing and tilt of the stands does not matter at this point. Just make sure to use the same holes on right and left side. Note the placement of the stands in reference to the wing mounts and base plates. The stands are attached to the inner surface of both the wing mounts and base plates. Failure to follow this positioning we result in incorrect positioning of the base plates when mounting to the trunk.
-
Open the trunk and remove the inner liner on the underside of the trunk
-
On the top surface of the trunk lay down painter’s tape in the general area where the wing will be mounted.
-
Using a sharpie, mark the center of the circle on the areas shown on the underside of the trunk. The distance between these holes should be ~16 13/16ths inches or ~427mm. Verify this to be the same distance between the inner front holes on the base plates.
-
Use a center punch to mark where you will be drilling.
-
Drill a small pilot hole for each mark We suggest starting with a pilot hole for each for verification before going to the actual hole size.
-
Close the trunk, and place the wing assembly on the trunk to ensure your holes line up with the holes in the base plates.
-
Once verified, set the wing assembly aside and enlarge the holes with a 15/64 drill bit or to ~5.9mm.
-
Set the wing assembly back onto the trunk and secure with M6 hardware.
-
Mark the remaining six holes using the base mount plates as your guide.
-
Remove the wing assembly from the trunk.
-
Center punch the six marked spots. Drill small pilot holes Be mindful of the drill depth for the four rearward holes as the bottom side of the trunk has layers.
-
Place the wing assembly back onto the trunk to verify the position of all the holes.
-
Remove the wing assembly and drill the holes using a 15/64 bit or ~5.9mm.
-
Clean the holes, top and bottom from debris.
-
Remove the painter’s tape on the top side of the trunk
-
Attach the supplied foam pads to each base mount plate. The adhesive side should be attached to the base mount plate, not the trunk. There is a left and a right foam pad.
-
Place the wing assembly back on the trunk and secure with the supplied M6 hardware. Torque to recom mended spec.
NOTE: spec may vary if not attaching to an OEM metal trunk, in which case use your best descretion. -
Attach the wing plates using the supplied M8 bolts and countersunk washers. Hand tighten or torque to recommended spec. Do not over-tighten.
-
Now, tilt of the stands and angle of wing can be adjusted to desired position. When satisfied, torque M6 hardware to recommended spec.
-
Use soap and water or a quick detailer-type product to clean the entire wing assembly.
-
Re-install the inner trunk lid liner.
WARRANTY POLICY
- 1-year limited manufacturer defect warranty from date of purchase.
- All warranty claims are subject to inspection by rmk-design at our facility.
- Limited Warranty only applies to the original purchaser of the product.
- rmk-design is not responsible for fitment issues on non-US spec vehicles as all products are developed on US spec models.
- It is the purchaser’s responsibility to ensure this product does not violate any City, County, State, or Federal laws or regulations.
- Product finishes are not covered under warranty and considered wear & tear.
- No warranty whatsoever will be valid if the defect was caused by abuse, negligence and/or mishandling. That includes weather conditions, natural disasters, any road/off-road conditions, and any accidents/collision you were part of.
- Modification, mis-installation, tampering, and installation on vehicle not intended voids all warranty.
- Some chemical cleaning products may damage the product and/or finishes.
- Wear and tear (the damage that happens to our product in ordinary use) is not covered by our limited warranty.
- Improper installation or misuse of the product may lead to failure and damage to both product and vehicle. The user assumes all responsibility.
- Vehicle manufacturer warranty may be voided should any modification(s) OEM(factory) components are detemined.
- User assumes all cost and risks associated with purchase and installation of aftermarket components. rmk-design is not responsible for any fees, fines, or any type of penalties you have received from any authority.
- Buyers are responsible for all return shipping fees unless otherwise noted.
- rmk-design does not cover any installation, uninstallation, labor fees, or related.
16872 Hale Avenue Suite A, Irvine CA 92606
Web: www.rmk-design.com
E-mail: info@rmk-design.com
Tel: 949-336-7661
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>