dewenwils HOWL07B Outdoor Wall Light Instruction Manual
- June 13, 2024
- dewenwils
Table of Contents
dewenwils HOWL07B Outdoor Wall Light
Product Information
- Product Name: Outdoor Wall Light
- SKU: HOWL07B
- Input Voltage: 120VAC 60HZ
- Maxload Power: Incandescent Bulb 60W
- Socket Type: Standard medium E26 (bulb not included)
- Material: Die-casting Aluminum and Water Ripple Glass
- Certification: ETL
Product Usage Instructions
- Read the warning signs and instructions in the manual before operating.
- Clean the glass and photocell sensor surface of the wall light with a soft and damp cloth to remove dust, as it can affect the sensitivity of the photocell and brightness of the light.
- Connect the black live wire, white neutral wire, and ground wire together using the provided wire connectors. Ensure that the connections are sturdy.
- Fix the lamp on the wall using the mounting screws. To install the A19 bulb (E26 base), first, unload the light body by removing two screws, then insert the bulb into the wall light. Note that the bulb is not included with the product.
- Turn on the main switch to restore power. The light will automatically turn on at dusk and off at dawn.
- To adjust the settings of the lamp, follow the instructions provided in Figure 1-4:
- Turn on the light and wait for 30 seconds for the sensor to warm up.
- Unscrew the top knob and cover to access the different modes, sensitivity, and delay time.
- Adjust the modes, sensitivity, and delay time as desired.
- Reinstall the top knob and cover to ensure waterproofing reliability.
- The lighting time can be adjusted by turning the Time knob clockwise to increase the lighting time and counterclockwise to decrease it. For every 1/4 clockwise rotation, the lighting time increases by 60 seconds, with a maximum of 180 seconds.
- The Sens knob can be adjusted to set the sensing distance. Turn it clockwise to increase the sensing distance and counterclockwiseto decrease it. The factory preset distance is 10 meters, but it can be adjusted within the range of 3-10 meters.
- Note that the Low-Level function is not applicable in AUTOmode.
Warning: Risk of fire. Min 75°C supply conductors. Consult a qualified electrician to ensure correct installation.Before installation, please turn off the main power of the circuit breaker to prevent possible electric shock.
Packing list
| IDX | ITEM NAME | SPEC | QUANTITY | NOTE |
|---|---|---|---|---|
| 1 | Wall light | 16.85” x7”x6.3” | 1 pc | |
| 2 | Wire connectors | P3 | 3 pcs | |
| 3 | Mounting screw | M4x25mm | 2 pcs | |
| 4 | Instruction manual | A5 PAPER | 1 pc |
Product specifications
- Input Voltage: 120VAC 60HZ
- Maxload Power: Incandescent Bulb 60W
- Socket Type: Standard medium E26( bulb not included)
- Materal: Die-casting Aluminum and Water Ripple Glass
- Certification: ETL
Installation Instructions
POWER OFF
STEP 01: POWER OFF
- FIG.1. Turn the wall switch to the “OFF” position. Depending on which type of fuse box in your home:
- FIG.2. Either turn the main (Master) switch to the “OFF” position to cut off the power supply of the entire home, or turn off the individual switch that supplies power to the fixture installation location. OR
- FIG.3. Either turn the main (Master) switch to the “OFF” position to cut off the power supply of the entire home, or unscrew the fuse that supplies or turn off the individual switch that supplies power to the fixture installation location
STEP 02: CLEAN THE LIGHT
- Cleaning: Cleaning the glass and photocell sensor surface of the post light with a soft and damp cloth.Dust will affect the sensitivity of photocell and brightness of the post light.
STEP 03: CONNECT THE WIRE
- Connect black live wire, white neutral wire and ground wire with wire connectors,be sure that the wires are connected together sturdily.
STEP 04: FIX THE LIGHT
- Fix the lamp on the wall with mounting screws,unload the light body by taking off two screws,install A19 bulb(E26 base) in the wall light. (Not included)
STEP 05: POWER ON
- Turn on the main (Master) switch to get the power back, the light will turn on automatically at dusk and off at dawn.
The lamp structure is described as following picture:
Operation description
- Turn on the light, wait 30 seconds for the sensor to warm up, then select one function.
- Unscrew the top knob and top cover, then you can adjust different modes, sensitivity and delay time. Reinstall the top knob and cover after completing the setting to ensure waterproofing reliability, as shown in Figure 1~4.
Remark: The lighting time can be adjusted. Factory setting is AUTO mode
(20 second, the maximum preset induction distance is 10 meters.)
AUTO MODE – Set the slide switch to AUTO. The fixture will stay off at
daytime and automatically turn on when human body activity is sensed at night.
It automatically turns off when the person leaves or remains stationary for
20-180 seconds(according to the time you set). The factory preset time is 20s
and the brightness is 100%.
TIME – Adjust Lighting Time: Adjust the “Time” knob with a flat head
screwdriver(Not Included). Turn clockwise to increase the lighting time, and
counterclockwise to decrease the lighting time. For every 1/4 clockwise
rotation, the lighting time increases by 60 seconds. The maximum is 180
seconds.
SENS – Adjust Sensing Distance: Adjust the “Sens” knob with a flat
headscrewdriver(Not Included). Turn clockwise to increase sensing distance,
and counterclockwise to decrease the sensing distance. The factory preset
distance is 10M(Maximum), you can adjust the “Sens” knob to set it in the
range of 3-10 meters.
LOW LEVEL – This function is out of work in AUTO mode.
AUTO+ MODE: Set the slide switch to AUTO+.The fixture will stay OFF at
daytime and stay low-level brightness (20%-50% brightness to be manually
adjusted)at night if no motion is detected within 20-180 seconds，and
automatically adjust the brightness to 100% when human body activity is sensed
at night. It returns to the preset low-level brightness again when the person
leaves or remains stationary for 20-180 seconds (according to the time you
set). The factory preset time is 20s and the brightness is 20%.
TIME – Adjust Lighting Time: Adjust the “Time” knob with a flat head
screwdriver (Not Included). Turn clockwise to increase the lighting time, and
counterclockwise to decrease the lighting time. For every 1/4 clockwise
rotation, the lighting time increases by 60 seconds. The maximum is 180
seconds.
SENS – Adjust Sensing Distance: Adjust the “Sens” knob with a flat head screwdriver(Not Included). Turn clockwise to increase sensing distance, and counterclockwise to decrease the sensing distance. The factory preset distance is 10M(Maximum), you can adjust the “Sens” knob to set it in the range of 3-10 meters.
LOW LEVEL – Adjust low-level brightness: Adjust the “Sens” knob with a
flat head screwdriver(Not Included). Turn clockwise to increase brightness,
and counterclockwise to decrease brightness.
Note: This function is only available for Incandescent bulbs or dimmable
LED bulbs.
PC MODE: Lights off during the day and on at dusk. Other functions are out of work.
NOTE:
- The sensitivity of the motion sensor will increase as the environmental temperature drops. For best performance, gently clean the lens with a soft cloth every 1 or 2 months to ensure maximum sensitivity.
- The magnitude of adjustment for sensitivity and time may not be precisely correspond to the amount of the knob is turned.
- When installed at a height of 6.5 feet, at 77 degrees Fahrenheit, the light will provide a maximum detection distance of 40 feet and detection range of 180 degrees. (See Fig.11 Fig.12)
- The sensor will be more sensitive to motion across its detection path than motion directly towards it. (See Fig.13)
- To reduce possible nuisances, do not mount the fixture near a heat source like an air conditioner, vent or furnace exhaust, or in a direction facing any reflecting object or other light sources.
- Be sure the light is mounted straight on the wall; otherwise, the detection distance may be limited.
Aftersales service
Warrants this product to be free from defects in material and workmanship for a period of one year from the date of purchase. Warranty is void if damage is caused by misuse or improper installation. Our dedicated customer service team will get back to you within 24 hours.
Aftersales FAQS
- Is there any matching POST LIGHT for sale?
- Yes, we have matching POST LIGHT for sale, you can buy it in our store.
- Is the light bulb replaceable?
- Yes. But the light bulb is not included. You can replace it with a suitable bulb (A19 bulb is recommended). Please cut off the power before replacing the bulb.
- Can this lamp be used outdoors in rainy and snowy weather?
- Yes. With a rubber pad at the top and a drainage hole at the bottom, the post light can discharge condensed water and other accidental water effectively.
Limited Warranty
One Year Limited Warranty
Supported by our professional R&D team and QC team, we provide One Year
Warranty for materials and workmanship from the purchase date. Please note
that the warranty does not cover damage caused by personal misuse or improper
installation. Please attach your Order ID and Name so that our dedicated
customer service team can help you better. Please pay attention to the warning
signs Read the instructions with caution before operating and keep it properly
SKU: HOWL07B [Instruction Manual]
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>