GRUPA BA-T Table Lamp And Floor Lamp User Manual
- June 17, 2024
- GRUPA
Table of Contents
GRUPA BA-T Table Lamp And Floor Lamp
Specifications
- Product: Baluna Table Lamp and Floor Lamp
- Manufacturer: GRUPA
- Light Source Energy Efficiency Class : E
- Indoor Use Only
Product Usage Instructions
Assembly:
- Unscrew the diffuser (part A) while holding the metal ring (part B).
- Insert the light bulb and gently mount the diffuser back to the metal ring by screwing it in place.
Important Safety Instructions:
- Installation and use must follow provided instructions for product safety.
- Installation should be done by a qualified electrician.
- The luminaire must be connected to a grounding electrical system.
- Always turn off power before installation or maintenance.
- Choose appropriate fittings for different materials.
Warnings:
- Avoid using force during assembly.
- Ensure luminaire balance on even surfaces.
- Do not disassemble the product.
- For indoor use only, do not expose to water.
Cleaning Instructions:
- Clean powder-coated surfaces with pH-neutral detergents and soft cloths.
- Avoid cleaners with granular substances, acetic acid, or citric acid.
Features:
Rotate the switch for turning ON-OFF or dimming the lamp.
Manufacturer Information:
- Manufacturer: Grupa Studio d.o.o. Popa Dukljanina 1 10000
- Zagreb, Croatia, EU
- Email: info@grupa.com
- Website: grupa.com
FAQ
-
Can I use a different light bulb than the one provided?
To ensure proper functioning and safety, it is recommended to use the same type of light bulb provided with the luminaire or suggested by the manufacturer. -
How should I clean the lamp?
Use pH-neutral detergents and soft cloths to clean powder-coated surfaces. Avoid cleaners with granular substances or acids.
Assembly
-
Unscrew the dffuser (A) while holding the metal ring (B).
-
Insert the light bulb then gently mount the diffuser screwing it back to the metal ring.
Important
- The safety of this product can only be guaranteed if these instructions are observed, during both installation and use. We advise keeping these instructions.
- If the product requires installation, it should be performed by a qualified electrician.
- This luminaire must be connected to a grounding electrical system. Always turn off power to the system before starting installation work. Whenever acting on the luminaire (i.e. changing the light bulb), ensure that the power supply has been switched off.
- Different materials require different types of fittings.
- Always choose screws and plugs that are best suited for the material on which you are installing the luminaire.
Warning
- This product has been carefully handmade and due to the nature of such work please allow slight variations in the surface of the material.
- Do not use force to assemble the luminaire. Always pay attention to the luminaire balance, do not place or install the luminaire on uneven surfaces.
- Do not disassemble this product. Grupa declines all responsibility for products that are modified without prior authorization.
- This product is for indoor use only. Do not immerse this product into water.
- Regularly check that there is no damage to cables and other parts. If the external cable of this luminaire is damaged, it must be exclusively replaced by the manufacturer or its authorized service agent or similar qualified persons in order to avoid a hazard.
Light Source
- If delivered with a light source, this product contains a light source of energy effciency class E.
- Grupa guarantees that the luminaire will work properly only with the light bulb provided with the luminaire or suggested by the manufacturer. Should you exchange the light bulb, we suggest to use the same type as provided with the luminaire. Never touch the light bulb when the luminaire is turned on, or shortly after it is turned off because it can be hot and can cause burns.
- Do not touch the inner surfaces of the luminaire that may be hot.
Environment
Do not throw this product in regular household trash but in a proper waste disposal that is suitable for similar electrical appliances.
Cleaning
- Powder-coated surfaces should be cleaned with aqueous solutions made from pH-neutral detergents or cleaning products and soft, non-abrasive cloths, rags or industrial cotton batting.
- Always clean metal surfaces gently and without scrubbing so that the surface is not scratched. Never use cleaners containing granular substances, acetic acid or citric acid.
Features
Rotate the switch for turning ON-OFF or dimming the lamp
ABOUT COMPANY
- Manufacturer: Grupa Studio d.o.o. Popa Dukljanina 1 10000
- Zagreb, Croatia, EU
- Email: info@grupa.com
- Website: grupa.com
References
Read User Manual Online (PDF format)
Loading......