DAISOTWS003 True Wireless Earphone Instruction Manual
- May 15, 2024
- DAISO
Table of Contents
DAISOTWS003 True Wireless Earphone
Product Information
Specifications :
- Model : DAISO_TWS003
- Weight : 64#5ZQF$
- Dimensions : -3
Product Usage Instructions
- Connect the device to a power source using the provided cable.
- Press and hold the power button to turn on the device.
- Pair the device with your smartphone or other Bluetooth-enabled devices.
- Enjoy wireless audio playback or hands-free calling.
Maintenance :
Regularly clean the device with a soft, dry cloth to prevent dust buildup.
Avoid exposing the device to extreme temperatures or moisture.
Troubleshooting:
If you encounter any issues with the device, refer to the troubleshooting
section in the user manual or contact customer support for assistance.
Frequently Asked Questions (FAQ):
-
Q: How do I pair the device with my phone?
A: To pair the device, make sure it is in pairing mode, then go to the Bluetooth settings on your phone and select the device from the list of available devices. -
Q: How long is the battery life of the product?
A: The battery life of the product is approximately X hours on a full charge, depending on usage. -
Q: Can I use the product while charging?
A: Yes, you can use the product while it is charging. However, it is recommended to let it fully charge before initial use for optimal battery performance.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
- If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment
This device contains licence-exempt transmitter(s) that comply with
Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:
- This device may not cause interference,
- This device must accept any interference, including interference that may cause undesired operation of the device
FCC ID : 2BCCJ-DAISOTWS003
DAISO
Model: TWS003
Complies with IMDA Standards DA107974
True wireless earphone instruction manual
Charging case Earphones Supplied items Instruction manual (this manual)
Names of parts
CAUTION
- Make sure to read the usage precautions carefully to ensure safe use of the product. Failure to follow the warnings and precautions herein may result in injury (injury, disability or death) to yourself or a third party, or damage (malfunction, damage, destruction or loss) to property.Do not use this product for purposes other than its intended purposes or in any other way than described. Pictures herein are for illustrative purposes only.
- Never use while cycling or driving a car or motorcycle. This can result in a traffic accident. Do not use in places where it is dangerous not to hear your surroundings, such as at a train crossing, train platform, roadway or construction site.
- Noise may occur and audio may be interfered depending on the connected Bluetooth device or communication environment and depending on surrounding conditions (crowded places, train station platform, inside a train, places with large numbers of communication devices).
- Continuous use at a loud volume that stimulates the ears can significantly damage your hearing.
- Raising the volume too high initially can damage hearing when a loud sound is output suddenly. Use while raising the volume gradually.
- Be careful not to make the incoming call volume too loud.
- Immediately discontinue use if the product becomes deformed or damaged.
- Stop use immediately if skin irritation occurs when in contact with the product.
- Do not disassemble or modify.
- Do not drop or subject the product to excessive impact.
- Not water-resistant. Do not touch charging case terminals or earphone terminals with wet hands.
- Do not let the product become wet or operate with wet hands.
- Do not let thinner, benzene, alcohol etc. remain on the product.
- Do not charge with a current exceeding 5V / 1A. Do not use with a high-speed charging adapter.
- Do not leave if charging is completed.
- For safety, do not start the engine of a car with a charging cable connected from a car charger to the charging port of the product. Always connect the charging cable after starting the engine.
- Do not use or store the product in the following places. Places where strong magnetic fields are generated. Places where static electricity or electrical noise are generated. Places where condensation forms. Places where there is a risk of short circuit or water leaks. Places subject to high temperature or high humidity. Places subject to direct sunlight. Around fires or places where hot air is trapped. Dusty places.
- Do not cover with blankets, pillows or other bedding while in use.
- Keep away from fire and other sources of heat.
- Children must be supervised by a guardian when using the product.
- Do not dispose with regular garbage (noncombustible garbage).
- This product may only be used in countries where it complies with or is certified to comply with radio laws of the country. It cannot be used outside the country of sale.
- This product uses a frequency of 2.4GHz.
- The audio may be interfered by devices using the same 2.4GHz band radio waves, such as Bluetooth devices, wireless LAN or WiFi devices, digital cordless phones and microwaves.
- Do not use in areas where radio waves are prohibited, such as hospitals. Use of this product may affect pacemakers and other medical devices and medical electronics.
- Check with your airline regarding the use of wireless devices on board the aircraft.
- Read the instruction manual of the connected device before use.
- While this product can be used to connect to a mobile phone or computer, the setup method and precautions vary depending on the connected device.
- The battery is a consumable product that deteriorates with normal use. Battery drain is a characteristic of the product and does not indicate a malfunction. Battery cannot be replaced.
How to use
- Usable functions vary depending on the connected device and app.
- Even if the above operations are performed, a different operation may occur or the operation may not work
Charging
Charge the charging case and earphones before using.
Charging the charging case
Connect the charging cable to the USB Type C port on the charging case to
charge. The LED blinks red while charging and lights red when fully charged.
charging cable not included. Provide your own USB Type C charging cable.
Charging the earphones
-
Store the earphones in the charging case that has been fully charged. The earphone LED lights red when charging starts. The earphones LED lights blue when charging is completed and turns off. When the earphones are being charged, the charging case lights blue.
-
If the charging case runs out of power while the earphones are stored inside, the earphones may automatically turn on and enter pairing mode.
If the charging case runs out of power while the earphones are stored inside, the earphones may automatically turn on and enter pairing mode. When the remaining battery power of the earphones is low, an alert sounds. -
The remaining battery power indicator of the earphones on the connected device indicates the remaining battery power of one earphone.
-
The earphone that loses power first will turn off. (With one side ON)
-
If the earpieces are not positioned correctly, this could interfere with the case, preventing charging. Also, strong shock can dislodge the earphones from the charging case, preventing charging.
-
If not used for a prolonged period of time, make sure to charge once every few months to prevent deterioration due to self-discharge of the battery.
Charge the charging case.
If the battery case LED blinks blue when the earphones are stored, the
remaining battery power of the charging case is low. Charge the charging case.
Turning on and off
The earphones turn on automatically when removed from the charging case and turn off when stored.
-
Turning on:
Remove the earphones from the charging case to turn them on automatically. To manually turn on the earphones, press and hold the Operation button on the earphones for 3 seconds while the power is off. The earphone LED lights blue and the power turns on. -
Turning off:
Store the earphones in the charging case to turn them off automatically. To manually turn off the earphones, press and hold the Operation button on the earphones for 3 seconds while the power is on. The earphone LED blinks red and the power turns off.
If communication with the connected device is interrupted and the earphones are unable to connect, the earphones enter power save mode. If the earphones are unable to reconnect in power save mode, the power turns off automatically in a few minutes.
How to clean
Wipe clean with a soft cloth.
Pairing and connecting the earphones
(registering them to a device for the first time)
-
1. Remove the earphones from the charging case.
When both earphones are removed from the charging case, the earphones pair automatically to each other, and the parent earphone enters pairing mode. In pairing mode, the parent earphone LED blinks alternately red and blue. -
2. In the Bluetooth settings of the connecting device, select the earphones to complete pairing.
Once paired, the earphones pair automatically the next time and thereafter.
To pair to another device, disconnect Bluetooth from the connected device, and
repeat steps 1 and 2 above to pair to the new device.
If pairing fails
- Check that Bluetooth is enabled on the connecting device.
- Check that the connecting device supports the profile of this product.
- In the Bluetooth settings of the connecting device, delete the earphones and try pairing them again. Pairing may not work if there are nearby electronic devices that generate strong electromagnetic waves. Move away from other electronic devices or turn off the power and then try pairing again.
Recommended Example of Attaching the Earphones
- Check the -L- (left) and -R- (right) indicators on the inside of the main unit. The sound quality changes depending on the attachment position.
- Adjust to the desired position.
- Adjust the position if it is difficult to hear the audio.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>