SEALEY MIG-N315 MIG Torch with 3m Euro Connection Instruction Manual
- June 1, 2024
- SEALEY
Table of Contents
SEALEY MIG-N315 MIG Torch with 3m Euro Connection
Product Usage Instructions
Before using the product, ensure you are familiar with the safety warnings and instructions for the welder to which the torch is to be fitted.
- Do not exceed the rated current of the torch.
- Do not use if any part of the torch, cable, or connector is damaged. Use genuine Sealey replacement parts for repairs.
- Avoid contact of the cable with sharp or hot items.
- Always wear the correct personal protective equipment specified in the welder instructions.
FAQ
- Q: Can I use this torch with a welder that has a higher rated current than specified?
- A: It is not recommended to exceed the rated current of the torch as it may cause damage or unsafe operation.
- Q: How should I dispose of the product when it becomes unserviceable?
- A: When disposing of the product, recycle unwanted materials instead of disposing of them as waste. Drain any fluids into approved containers and dispose of the product according to local regulations.
Thank you for purchasing a Sealey product. Manufactured to a high standard,
this product will, if used according to these instructions, and properly
maintained, give you years of trouble-free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE
OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND
WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE
INSTRUCTIONS SAFE FOR FUTURE USE.
SAFETY
- BEFORE USE, ALWAYS ENSURE THAT YOU ARE FAMILIAR WITH THE SAFETY WARNINGS AND INSTRUCTIONS FOR THE WELDER TO WHICH THIS TORCH IS TO BE FITTED.
- DO NOT exceed the rated current of the torch.
- DO NOT use if any part of the torch, cable or connector is damaged in any way. Use only genuine Sealey replacement parts to effect repairs.
- DO NOT allow the cable to come into contact with any sharp or hot items.
- Always use the correct personal protective equipment as specified in the welder instructions.
INTRODUCTION
- Professional MIG welding torches with contoured grip, hanging hook and heat-proof cable.
- Fitted with a Euro connection enabling a quick and simple plug connection to the welder.
- No wiring means the torch can be disconnected and stored safely.
SPECIFICATION
Model No:| MIG/N315| MIG/N325| MIG/N336| MIG/N415|
MIG/N425| MIG/N436
---|---|---|---|---|---|---
Rated Current:| 180A| 230A| 250A| 290A| 340A| 350A
Wire Diameter:| 0.6-1mm| 0.8-1.2mm| 0.8-1.2mm| 0.8-1.2mm| 0.8-1.6mm| 1-2.4mm
Length:| 3mtr| 3mtr| 3mtr| 4mtr| 4mtr| 4mtr
Torch Type:| MB15| MB25| MB36| MB15| MB25| MB36
TIP & SHROUD REMOVAL
ENSURE THAT THE TORCH IS COOL AND THAT THE WELDER IS DISCONNECTED FROM THE POWER SUPPLY.
MIG/N315, MIG/N415, MIG/N325, MIG/N425 (fig.1)
- To remove the shroud: turn the shroud clockwise and pull away.
- To remove the tip: unscrew the tip in an anticlockwise direction.
- To replace the tip: screw it back in and tighten it.
- To replace the shroud: simply push the shroud back over the spring.
MIG/N336, MIG436 (fig.2)
- To remove the shroud: pull the shroud forward to release.
- To remove the tip: unscrew the tip in an anticlockwise direction.
- To replace the tip: screw it back in and tighten it.
COUPLING THE EURO CONNECTOR
Ensure that the welder is disconnected from the power supply before connecting the torch.
- Line the male and female connector up carefully and insert the torch connections. (fig.3).
- Screw the outer collar around the torch onto the welder torch connector to fix it in place. (fig.4).
- See the welder instructions for wire feed details.
ENVIRONMENT PROTECTION
- Recycle unwanted materials instead of disposing of them as waste.
- All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.
- When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.
WEEE REGULATIONS
- Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment (WEEE).
- When the product is no longer required, it must be disposed of in an environmentally protective way.
- Contact your local solid waste authority for recycling information.
NOTE: It is our policy to continually improve products and as such we
reserve the right to alter data, specifications and parts without prior
notice.
IMPORTANT: No Liability is accepted for incorrect use of this product.
WARRANTY
- Guarantee is 12 months from purchase date, proof of which is required for any claim.
CONTACT
- Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
- 01284 757500
- sales@sealey.co.uk.
- www.sealey.co.uk.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>