SEALEY RE901 Adjustable Transpor Tacar Trolley Instruction Manual
- June 1, 2024
- SEALEY
Table of Contents
SEALEY RE901 Adjustable Transpor Tacar Trolley
Thank you
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to instructions
Wear safety footwear
SAFETY
✔Ensure the trolley is in sound condition and good working order. Take action
for immediate repair or replacement of damaged parts.
Use genuine parts only. The use of improper parts may be dangerous and will
invalidate the warranty.
‰ WARNING! Prepare the vehicle ready for resting and moving on the trolley.
Ensure the vehicle will not move, tip, fall etc once it has been
seated on the trolley. Take any necessary precautions to protect persons,
property and equipment when using this trolley.
✔Locate the trolley in a suitable, well lit working area.
✔Keep working area clean and tidy and free from unrelated materials.
✔Use trolley on level and solid ground, preferably concrete. Avoid tarmacadam
as trolley may sink in.
✔Ensure the vehicle engine is switched off .
✔Ensure there are no passengers in the vehicle.
✔Ensure all non-essential persons keep a safe distance whilst the trolley is
in use.
✔Only place trolley under those lifting points recommended by vehicle
manufacturer (see vehicle handbook).
✔Check the lifting point is stable and correctly held in trolley supports.
✔Ensure the trolley wheels are free to move and that there are no
obstructions.
✔Ensure you have a clear view and necessary assistance when transporting
vehicle.
✔ Ensure there are no persons or obstructions beneath the vehicle before
moving.
✔When stationary, always lock the two brake wheels.
✘ DO NOT operate the trolley if damaged.
✘ DO NOT allow untrained persons to operate the trolley.
✘ DO NOT exceed the rated capacity of the trolley.
‰ WARNING! DO NOT use the trolley to hold and move a vehicle which is
unstable.
✘ DO NOT allow the vehicle to move on the trolley.
✘ DO NOT move vehicle if there is a risk of spillage of fuel, battery acid, or
other dangerous substances.
✘ DO NOT work under the vehicle unless supported by axle stands which have
been correctly positioned.
✘ DO NOT ride on the trolley.
✘ DO NOT use the trolley without appropriate supports.
✘ DO NOT use the trolley for purposes other than which it is intended.
✔When not in use store trolley in a safe, dry, childproof area.
INTRODUCTION
Heavy-duty steel frame suitable for supporting partly dismantled or badly damaged vehicles. Enables easy movement around body shop. The supports are interchangeable between V-crutches and sill clamps. Supports and clamps adjustable for height and overall width. Fitted with four Ø125mm nylon castors, two of which lock.
SPECIFICATIONS
Model No:…………………………………………………… RE901
Capacity: …………………………………………………… 2 Ton
Closed Length: ……………………………………………. 600mm
Using with Crutches:
Minimum Height: …………………………………………. 250mm
Maximum Height: ………………………………………… 310mm
Using with Sill Clamps:
Minimum Height: …………………………………………. 330mm
Maximum Height: ………………………………………… 390mm
Minimum Width: ……………………………………….. 1035mm
Maximum Width: ………………………………………. 1430mm
*Widths measured between centres of jacking points
ASSEMBLY
-
Assemble four wheels with nuts, spring washer, washers, and bolts. Ensure that the two locking wheels are at the same end.
-
Remove extension arm (fig1.C) from main beam undoing knob (A) and lifting arm off.
-
Assemble main beam (C) to wheel frames by fixing with four bolts, spring washers, washers and nuts at each end (B).
-
Check that all connections are tight and replace the extension arm (C) by screwing knob (A) into the holding plate set inside the frame of the main beam.
-
Screw the appropriate supports into the end of the extension arm at point (X) and place the unused supports in their storage eyes (D).
‰ WARNING! Before use ensure Section 1 safety instructions are read and understood. -
Check and prepare the vehicle as mentioned in the safety instructions ensuring the ground on which the trolley is to travel is level and solid (not tarmacadam).
-
Position the trolley supports under the vehicle manufacturer’s recommended lifting point. If using the sill clamps ensure they are correctly fitted and tightened. Check that the vehicle is secure and there are no persons or obstacles beneath the vehicle or in the path of transportation. Ensure the wheel brakes are unlocked and move the vehicle.
-
When the trolley destination is reached, the trolley wheel brakes must be applied to stop further movement.
✘ DO NOT use trolley as a support stand for working on, or under, the vehicle. The trolley is designed for maneuvering only.
MAINTENANCE
-
Before each use check for broken, cracked, bent, or loose parts, or any visible damage. If any suspect item is found remove trolley from service and take necessary action to remedy the problem.
✘ DO NOT use the trolley if believed to have been subjected to abnormal load or shock load. -
Keep the trolley clean and periodically oil the wheel bearings.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools,
accessories and packaging should be sorted, taken to a recycling centre and
disposed of in a manner which is compatible with the environment. When the
product becomes completely unserviceable and requires disposal, drain any
fluids (if applicable) into approved containers and dispose of the product and
fluids according to local regulations.
REGISTER YOUR PURCHASE HERE
Note: It is our policy to continually improve products and as such we
reserve the right to alter data, specifications and component parts without
prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is
required for any claim.
Customer Support
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk.
IP32 7AR
01284 757500
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>