GLOW SHIFT 65mm Racing 30 PSI Turbo Boost Vacuum Gauge Kit Instruction Manual
- June 1, 2024
- GLOW SHIFT
Table of Contents
INSTALLATION INSTRUCTIONS
856.768.8300
TechSupport@GlowShiftGauges.com
65MM Boost/Vacuum Gauge Instructions
The following instructions are for the installation of your Boost / Vacuum Gauge. Before you begin, lay out all items and ensure there are no missing parts. If any items are missing, please STOP immediately and contact GlowShift Gauges.
What’s Included
- Boost/Vacuum Gauge
- 1/8” Barbed T-Fitting
- 6ft Silicone 1/8” ID Boost/Vacuum Line
- Mounting Bracket
- 2Hose Clamps
Wiring Schematic
Red: 12v Ignition Switched Source (+)
Orange: 12v Headlight Switched Source (+)
Black: Vehicle/Engine Ground (-)
WARNING
Disconnect negative battery terminal before starting any work on the
vehicle.
-
Locate a Vacuum Line that is coming directly off of the Intake Manifold after the throttle body. Some applications have an available port off of the Intake Manifold that you can connect to. You can also T off of the wastegate Vacuum Line if it is available.
-
Stretch out and make sure that the Boost/Vacuum Line is free of kinks.
-
Cut the Vacuum Line that is coming from the Intake Manifold that you are going to use and install the T-Fitting.
Make sure that the barb with the brass fitting is used for the gauge connection.
Note: If the Boost/Vacuum Line is not in line with the brass fitting the gauge could flutter or make noise. -
Slide the Boost/Vacuum Line onto the T-Fitting and secure with the supplied clamp.
-
Route the Boost/Vacuum Line through the firewall from the engine bay, keeping it clear of any moving parts, heat sources, and kinks.
Note: Be sure to use a grommet when routing the line through the firewall to protect it from being cut or damaged. If one is not available you will need to drill a hole and install a grommet.
-
Slide the Boost/Vacuum Line onto the back of the Gauge and secure the supplied clamp.
Gauge Wiring
-
In order to test for power, reconnect the Negative Battery Terminal.
-
It may be necessary to remove Vehicle Trim and/or Kick Panels in order to gain access to the vehicle’s Fuse Box.
-
Using a Test Light, locate a Switched 12-Volt Power Source in the vehicle’s Fuse Panel that receives 12-Volt power when the ignition is turned on. You can splice into the circuit or use an optional expandable circuit, connect the Red Wire of the gauge to the Switched 12-Volt Power Source.
Note: It is required to use an automotive grade 1820 gauge wire and proper splice connectors when extending any of the power wires. -
Connect the Orange Wire of the gauge to the positive head light switch Power Source using a Splice Connector or Expandable Circuit either in the Fuse Box or the switch itself in order to have the gauge face dim 30% when the headlights are turned on.
Note: Make sure that the connection source is not adjustable. If the voltage is reduced when you lower the Dimmer Wheel it could cause the gauge to flash from not having enough voltage.
-
Locate a clean, reliable grounding source and connect the Black Wire from the gauge.
-
After all wiring is complete, turn the vehicle’s key to the “On” position and ensure your gauge illuminate.
-
Reinstall any panels that may have been removed.
-
Turn on the headlights to ensure that the gauge is dimming properly.
-
Start the vehicle and check for leaks.
-
Test drive your vehicle to ensure your gauge is functioning properly.
-
Locate a clean, reliable grounding source and connect the Black Wire from the gauge.
-
After all wiring is complete, turn the vehicle’s key to the “On” position and ensure your gauge illuminate.
-
Reinstall any panels that may have been removed.
-
Turn on the headlights to ensure that the gauge is dimming properly.
-
Start the vehicle and check for Vacuum leaks.
-
Test drive your vehicle to ensure your gauge is functioning properly.
Note: The Boost / Vacuum Gauge will only read positive pressure while under a load. Make sure to drive the vehicle in order to check the operation of the Boost / Vacuum Gauge.
ONE YEAR NON-TRANSFERRABLE LIMITED WARRANTY & DISCLAIMER
GlowShift Gauges, LLC (“GlowShift”) warrants to the original retail consumer
purchaser, and not any other purchaser or subsequent owner, that this Product
will be free from defects in material or workmanship for a period of one (1)
year from the purchase date.
For a period of one (1) year from the date of purchase, at no charge to the
Purchaser, GlowShift will repair or replace this Product if it is determined
by GlowShift to be defective. After the warranty period, the Purchaser must
pay all charges for parts and labor.
Coverage under this warranty is only valid within the United States, including
its territories, as well as in certain other countries. Purchasers should
check our website, www.GlowShift.com, to determine the warranty coverage in
the countries in which they are located.
GlowShift does not warrant the installation of the Product, which is the sole
responsibility of the Purchaser. Installation should be done by licensed
professionals.
Improper installation may cause damage to the Product and any vehicle in which
it is installed, and may cause burns and electrical injury to individuals.
GlowShift’s warranty does not cover any expenses incurred in removing Products
that are defective or re installing replacement Products in their place.
During the warranty period, to have the Product repaired or replaced, the
Purchaser must return the Product, freight prepaid by the Purchaser, to
GlowShift (but for customers in the contiguous United States, GlowShift will
pay the shipping charges if any Product fails during the first thirty (30)
days after purchase). The Product must be returned in its original carton or
in a similar package affording an equal degree of protection. GlowShift will
return the repaired or replaced Product, freight prepaid, to the Purchaser.
GlowShift does not provide Purchasers with temporary replacement units during
the warranty period or at any other time.
This limited warranty is non transferrable and will automatically terminate if
the original retail consumer purchaser resells the Product or transfers the
vehicle in which the Product is installed. An “original retail consumer
purchaser” is a person who originally purchases the Product, or a gift
recipient of a new Product that is in its original packaging and unopened.
This limited warranty is subject to all of the following terms and conditions:
TERMS & CONDITIONS
-
NOTIFICATION OF CLAIMS; WARRANTY SERVICE: If Purchaser believes that a Product is defective in material or workmanship, written notice with an explanation of the claim shall be given promptly by Purchaser to GlowShift. All warranty claims must be made within the warranty period, and any Products returned to GlowShift must be shipped in accordance with GlowShift’s procedures (including use of RMA numbers supplied by GlowShift after notification). The repair or replacement of any Product or part thereof shall not extend the original warranty period. The specific warranty on the repaired part only (not including gauge sensors) shall be in effect for a period of ninety (90) days following the repair or replacement of that part, or the remaining period of the Product warranty, whichever is greater. GlowShift does not provide a warranty on replacement gauge sensors.
-
EXCLUSIVE REMEDY; ACCEPTANCE: Purchaser’s exclusive remedy and GlowShift’s sole obligation is to supply (or pay for) all labor necessary to repair any Product found to be defective within the repair or replacement fails to remedy the defect. Purchaser’s failure to make a claim as provided in paragraph 1 above or continued use of the Product shall constitute an unqualified acceptance of such Product and a waiver by Purchaser of all claims thereto.
-
EXCEPTIONS TO LIMITED WARRANTY: GlowShift shall have no obligation to Purchaser with respect to any Product that is subjected to any of the following: abuse, improper use, negligence, accident, modification, failure to follow the operating procedures outlined in the user’s manual, failure to follow the maintenance procedures in the service manual for the Product, attempted repair by non qualified personnel, operation of the Product outside of the published environmental and electrical parameters, or if the Product’s original identification (trademark, serial number) markings have been defaced, altered, or removed. GlowShift excludes from warranty coverage Products sold AS IS and/or WITH ALL FAULTS. GlowShift also excludes from warranty coverage any consumable items such as fuses and batteries.
All software and accompanying documentation furnished with, or as part of the Product is furnished “AS IS” (i.e., without any warranty of any kind), except where expressly provided otherwise in any documentation or license agreement furnished with the Product. -
PROOF OF PURCHASE; REGISTRATION: The Purchaser’s dated bill of sale must be retained as evidence of the date of purchase and to establish warranty eligibility. Registration of any Product or of this limited warranty is voluntary, and failure to register will not diminish any rights available under this warranty.
DISCLAIMER OF WARRANTY
EXCEPT FOR THE FOREGOING WARRANTIES, GLOWSHIFT HEREBY DISCLAIMS AND EXCLUDES
ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR
ANY WARRANTY WITH REGARD TO ANY CLAIM OF INFRINGEMENT THAT MAY BE PROVIDED IN
SECTION 2 312(3) OF THE UNIFORM COMMERCIAL CODE OR IN ANY OTHER STATE STATUTE.
LIMITATION OF LIABILITY
THE LIABILITY OF GLOWSHIFT, IF ANY, AND PURCHASER’S SOLE AND EXCLUSIVE REMEDY
FOR DAMAGES FOR ANY CLAIM OF ANY KIND WHATSOEVER, REGARDLESS OF THE LEGAL
THEORY AND WHETHER ARISING IN TORT OR CONTRACT, SHALL NOT BE GREATER THAN THE
ACTUAL PURCHASE PRICE OF THE PRODUCT FOR WHICH SUCH CLAIM IS MADE. IN NO EVENT
SHALL GLOWSHIFT BE LIABLE TO PURCHASER FOR ANY SPECIAL, INDIRECT, INCIDENTAL,
OR CONSEQUENTIAL DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO,
COMPENSATION, REIMBURSEMENT OR DAMAGES ON ACCOUNT OF THE LOSS OF PRESENT OR
PROSPECTIVE PROFITS OR FOR ANY OTHER REASON WHATSOEVER.
GOVERNING LAW: This non transferrable limited warranty shall be governed by
the law of the State of New Jersey, U.S.A., and the United States of America,
excluding their conflicts of laws principles. The courts of Camden County, New
Jersey, shall have the exclusive jurisdiction over any legal action with
respect to this warranty.
This limited warranty gives specific legal rights. You may also have other
rights that may vary from state to state or from country to country. Some
states or countries do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitations and exclusions may not apply
to you. You are advised to consult applicable state or country laws for a full
determination of rights.
GlowShift Gauges, LLC
444 Commerce Lane Suite A
West Berlin, NJ 08091
GlowShift.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>