SEALEY CP1201 Cordless Combi Drill Instruction Manual
- June 1, 2024
- SEALEY
Table of Contents
SEALEY CP1201 Cordless Combi Drill
Product Information
Specifications:
- Brand: Sealey
- Model: [Insert Model Name]
- Usage: Power drill
- Power Source: Battery-operated
- Compliance: Machinery Directive 2006/42/EC
Product Usage Instructions
Safety Guidelines:
It is crucial to follow these safety guidelines to ensure safe and effective
use of the product:
- Wear protective gloves, eye protection, ear protection, and a mask.
- Maintain the drill and battery in good condition, checking moving parts alignment regularly.
- Use authorized service agents for repairs and replacements.
- Ensure the drill is switched off before installing the battery pack.
- Keep the drill and charger clean for optimal performance.
- Avoid loose clothing, jewelry, and secure workpieces properly.
- Assess the work area for potential hazards before operation.
- Properly insert and latch the battery pack before switching on the drill.
- Use appropriate safety gear and maintain correct balance and footing.
- Keep chuck direction switch locked until ready to use.
- Avoid operating the drill in the presence of flammable substances.
- Keep children and unauthorized persons away from the work area.
Hand Arm Vibration Guidelines:
To prevent Hand Arm Vibration Syndrome, adhere to the following guidelines:
- Operate the tool in accordance with the provided instructions.
- Conduct a specific evaluation of vibration emission before specialized tasks.
Frequently Asked Questions (FAQ)
Q: Can children operate the drill?
A: No, children should not operate the drill. Keep them away from the
working area for safety.
Q: Is it safe to operate the drill in wet locations?
A: No, do not get the drill or battery charger wet or use them in damp or
wet locations to avoid potential hazards.
12V SV12 SERIES CORDLESS COMBI DRILL
Ø10MM – BODY ONLY
MODEL NO: CP1201
Thank you for purchasing a Sealey product. Manufactured to a high standard,
this product will, if used according to these instructions,and properly
maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
SAFETY
GENERAL SAFETY
- Maintain the drill and battery in good condition. Check moving parts alignment on a regular basis.
- Replace or repair damaged parts. Use an authorised service agent and recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
- Ensure the drill is switched off before installing the battery pack.
- Keep the drill and charger clean for best and safest performance.
- Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
- Evaluate your working area before using the drill; e.g. ceilings, floors and enclosures may contain electrical items or water piping
- Ensure battery pack is correctly inserted into the drill handle and latched in place before attempting to switch on drill.
- Secure loose work pieces with a clamp, vice or other adequate holding device.
- Avoid unintentional starting.
- Wear approved safety eye protection (standard spectacles are not adequate).
- Maintain correct balance and footing. Ensure the floor is not slippery and wear non-skid shoes.
- Be aware that this drill does not need to be plugged into the mains power.
- Keep chuck direction switch in the locked position until the drill is required for use.
- Keep children and unauthorised persons away from the working area.
- DO NOT use the drill where there are flammable liquids, solids or gases, such as paint solvents, etc.
- DO NOT allow children to operate the drill.
- DO NOT operate the drill if any parts are missing as this may cause failure and/or personal injury.
- DO NOT hold unsecured work piece in your hand.
- DO NOT leave the drill operating unattended.
- DO NOT carry the drill with your finger on the power switch. Keep chuck direction switch in the locked position.
- DO NOT use the drill for a task it is not designed to perform.
- DO NOT operate the drill when you are tired or under the influence of alcohol, drugs or intoxicating medication.
- DO NOT get the drill or battery charger wet or use in damp or wet locations.
HAND ARM VIBRATION
WARNING! – Risk of Hand Arm Vibration Injury.
- This tool may cause Hand Arm Vibration Syndrome if its use is not managed adequately.
- This tool is subject to the vibration testing section of the Machinery Directive 2006/42/EC.
- This tool is to be operated in accordance with these instructions.
- Measured vibration emission value (a): 9.6m/s²
- Uncertainty value (k): 1.5 m/s²
- Please note that the application of the tool to a sole specialist task may produce a different average vibration emission. We recommend that a specific evaluation of the vibration emission is conducted prior to commencing with a specialist task.
- A health and safety assessment by the user or employer will need to be carried out to determine the suitable duration of use for each tool.
- NB: Stated Vibration Emission values are type-test values and are intended to be typical.
- Whilst in use, the actual value will vary considerably from and depend on many factors, such as the operator, the task and the inserted tool or consumable.
- NB: ensure that the length of leader hoses is sufficient to allow unrestricted use, as this also helps to reduce vibration.
- The state of maintenance of the tool itself is also an important factor, a poorly maintained tool will also increase the risk of Hand Arm Vibration Syndrome.
HEALTH SURVEILLANCE
We recommend a programme of health surveillance to detect early symptoms of
vibration injury so that management procedures can be modified accordingly.
PERSONAL PROTECTIVE EQUIPMENT
We are not aware of any personal protective equipment (PPE) that provides
protection against vibration injury that may result from the uncontrolled use
of this tool. We recommend a sufficient supply of clothing (including gloves)
to enable the operator to remain warm and dry and maintain good blood
circulation in fingers etc. Please note that the most effective protection is
prevention, please refer to the Correct Use and Maintenance section in these
instructions. Guidance relating to the management of hand arm vibration can be
found on the HSC website www.hse.gov.uk – Hand-Arm Vibration at Work.
INTRODUCTION
Compact, lightweight cordless drill/driver with added hammer function.
Comfortable composite housing with soft grip to reduce vibration.
Ø0.8-10mm Keyless chuck. 2-Speed settings and 21 torque settings provide the
control required to complete various tasks. All metal gear construction for
ultimate durability and performance. Integral LED battery level indicator and
LED worklight. Supplied with belt hook for safer storage while not in use.
Requires Model No. CP1200BP 12V 1.5Ah Lithium-ion Battery and Model No.
CP1200MC Battery Charger.
SPECIFICATION
-
Model No:………………………………………………….. CP1201
-
Battery Options (not included):…… 12V 1.5Ah Lithium-ion
………………………………………………… 12V 3Ah Lithium-ion
………………………………………………… 12V 4Ah Lithium-ion -
Chuck Size:………………………………………………… Ø10mm
-
Drilling Capacities:……………………………. Wood – Ø20mm
………………………………………………………..Metal – Ø10mm
…………………………………………………..Concrete – Ø10mm -
Impact Rate:……………………………… 0-6000/0-19500bpm
-
Maximum Torque:…………………………………………….25Nm
-
Noise Power/Pressure:……………………………. 80/69dB(A)
-
No-Load Speed:………………………………0-400/0-1300rpm
-
Replacement Parts:………… CP1200MC – Mains Charger
-
Vibration/Uncertainty:………………………………. 9.6/1.5m/s²
OPERATION
USING THE DRILL
- Ensure the direction selector (fig.1) is in the mid (lock) position.
- Open the chuck by turning the rear chuck collar.
- Insert the required drill or screwdriver bit into the chuck fully and tighten.
- The speed range of the drill is controlled by the speed selector on top of the casing (high for drilling, low for screwdriving)
- Select clockwise or anticlockwise direction by means of the direction selector.
- Select the required screwdriver / Drill / Hammer setting by turning the Hammer selector ring.
- Select the required screwdriver torque by turning the torque selector ring. The torque increases from 1-21.
- Squeeze the trigger to start the drill; initial pressure switches on the LED worklight, further pressure starts the motor and increases speed.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compli ance with the
EU Directive on Waste Electrical and Electronic Equipment (WEEE). When the
product is no longer required, it must be disposed of in an environmentally
protective way. Contact your local solid waste authority for recycling
information.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools,
accessories and packaging should be sorted, taken to a recycling centre and
disposed of in a manner which is compatible with the environment. When the
product becomes completely unserviceable and requires disposal, drain any
fluids (if applicable) into approved containers and dispose of the product and
fluids according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
[email protected]
www.sealey.co.uk