XR EL 12 Pro Platinum Shield Instruction Manual

XR EL 12 Pro Platinum Shield

Install Xréel camera lens protector

Step-by-step instructions to install Xréel camera lens protector

When installing a camera lens protector, it’s important to make sure that the camera lens is clean and free of dust or debris. Any particles on the camera lens can interfere with the adhesive, preventing the screen protector from sticking properly and can impact the quality of your pictures. It’s also important to apply the screen protector carefully, making sure that it’s aligned properly and that there is no dust trapped underneath it.

1. Use “Wet Wipe” to clean the phone camera lens. Wipe the camera lens dry with “Dry Wipe” or “Microfiber Cloth”. Then use ‘Guide Sticker” to remove dust.
2. Take off dust protector film from the camera lens protector.
3. Align small circle with Black edge with the camera flash light. slowly place it down on the camera.
4. Slowly press the camera lens protector down to make it attach to the camera lens.

*ONLY for Xréel products that include camera lens protectors.

Applying the screen protector

Step-by-step instructions for applying the Xréel phone screen protector on to your iPhone

When installing a screen protector, it’s important to make sure that the screen is clean and free of dust or debris. Any particles on the screen can interfere with the adhesive, preventing the screen protector from sticking properly. It is also important to apply the screen protector carefully, making sure that the screen protecter is aligned properly with the iPhone screen and that there are no air bubbles trapped underneath it.

• Wash your hands with soap. Make sure your hands are clean

• Turn off your phone

• Remove the phone case from your phone

• Thoroughly clean the phone with a towel

• Continue to clean the phone by using the “Alcohol Prep Pad” and the “microfiber cloth” provided to clean the phone screen from fingerprint, oil stains, etc.

• Make sure that there are no smudges, dust, or fingerprints on the phone screen

• Use the “dust-absorber sticker’ to pick up dust particles left on the phone screen

A screen protector is preinstalled on the alignment tray. Shocks and vibrations during transit may loosen the preinstalled screen protector from the alignment tray. Inspect the screen protector and make sure that the screen protecter isn’t loose. If it is, refasten the screen protector on the 3 notches on the alignment tray. If you are using the 2nd screen protecter, follow instructions provided on the next page to install the screen protector on to the alignment tray.

1. Align the “TOP” side of the “Alignment Tray” with the top side of your phone. Apply the “Alignment Tray onto your phone screen, then press it down to fasten it on your phone screen.
2. Please hold the upper section of the tray, as indicated in the picture. Then, carefully remove the plastic film from the opposite end of the alignment tray.
3. Use your index finger to gently apply pressure on the screen, swipe the bottom of the screen to activate the self-adhesive process. The self-adhesive process takes about 10 seconds.
4. After about 10 seconds, gently remove the alignment tray from the phone.
5. Check the screen for air bubbles. Try to remove the air bubbles from the screen protector by gently pushing the air bubbles out towards the edges of the protector with your fingers or a credit card. Final step, press around the edges to ensure the screen protector is property sealed.

Air bubbles that are trapped under a phone screen protector may sometimes disappear on their own over time, especially if the screen protector has been installed properly and the air bubbles are small. This is because the adhesive used on most screen protectors continues to dry and bond to the phone screen over the first few days after installation, which can help to eliminate any small air bubbles that may have been present.

Step-by-step instructions for installing screen protector on to alignment frame

1. Place the alignment tray in a horizontal position with the bottom facing upward.
2. Lift the PET film (2) and insert the end of (3) into the opening located at the bottom of the alignment tray, passing it through the opening.
3. Please ensure that you align the two positioning holes on the film with the two notches on the tray.
4. Gently use your fingernails to secure the two positioning holes onto the corresponding notches on the tray.
5. Gently secure the positioning hole at the opposite end onto the corresponding notch located at the bottom end of the tray
6. Insert the PET film 2) through the elongated opening located at the bottom of the tray. Installation Complete.

Scan

Scan the QR Code located below for installation videos on the Xréel YouTube Channel.
Watching the videos first before reading the instruction manual may be helpful.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>