SEALEY LED112.V2 Smd LED Extra Slim Flood Light Instruction Manual

SEALEY LED112.V2 Smd LED Extra Slim Flood Light

Product Information

• Specifications:
  • Model Numbers: LED112.V2, LED113.V2, LED115.V2
  • Type: SMD LED Extra-Slim Floodlight with Wall Bracket
  • Manufacturer: Sealey

Product Usage Instructions

• Safety
  • Electrical Safety:
  • It is crucial to adhere to the following electrical safety guidelines:
  • Installation by a qualified electrician is mandatory.
  • Inspect all electrical equipment and connections for wear and damage before use.
  • Minimize the risk of electric shock by using appropriate safety devices.
  • Connect the light to a suitable on/off switch.
  • Verify that cables and insulation are secure before connecting to the power supply.
  • Regularly check power supply, leads, and connections for wear, damage, and loose connections.
  • Ensure correct voltage matching between the product and power supply.
  • Avoid pulling the power cable after installation.
• General Safety:
  • Additional safety measures to consider:
  • Turn off mains power before performing maintenance.
  • Maintain the light in good condition; repairs should be done by a qualified electrician.
  • Use genuine parts for replacements or repairs.
  • Install the light vertically, avoiding horizontal surfaces like ceilings.
  • Avoid placing the light near flammable materials.
  • Avoid directing the light into people’s eyes to prevent potential eye damage.
  • Avoid installing the light where it may be easily knocked or hit.

FAQs

• Q: Can I install the floodlight myself without a qualified electrician?
  • A: No, the floodlight must be installed by a qualified electrician to ensure safety and proper functioning.
• Q: What should I do if I notice any damaged parts on the floodlight?
  • A: If you notice any damaged parts, replace or repair them using genuine parts only. Non-authorized parts may be dangerous and void the warranty.
• Q: How can I ensure the longevity of the floodlight?
  • A: Regular maintenance by a qualified electrician, following safety guidelines, and avoiding misuse will help ensure the floodlight’s longevity.

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble-free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

SAFETY

ELECTRICAL

• WARNING! It is the user’s responsibility to read, understand and comply with the following:
• WARNING! THIS PRODUCT MUST BE INSTALLED BY A QUALIFIED ELECTRICIAN.
• You must check all electrical equipment and appliances to ensure they are safe before use. You must inspect power supply leads and all electrical connections for wear and damage.
• You must ensure the risk of electric shock is minimised by the installation of appropriate safety devices.
• You must also read and understand the following instructions concerning electrical safety.
• Ensure the light is connected to an appropriate electrical on/off switch.
• Ensure the insulation on all cables and the product itself is safe before connecting to the main power supply.
• Ensure that cables are always protected against short circuits and overload.
• Regularly inspect the power supply, leads and all electrical connections for wear and damage, especially power connections, to ensure that none are loose.
• Ensure the voltage marked on the product is the same as the electrical power supply to be used.
• DO NOT pull the power cable once installed.
• DO NOT use worn or damaged leads, or connections. Immediately replace or have repaired by a qualified Electrician.
• Ensure the unit is correctly earthed and wired according to the following. (Installation should be undertaken by a qualified electrician)
  • a) Connect the green/yellow earth wire to the earth terminal ‘E’.
  • b) Connect the brown live wire to live terminal ‘L’.
  • c) Connect the blue neutral wire to the neutral terminal ‘N’.
• After wiring, check there are no bare wires, and that all wires have been correctly connected.

GENERAL SAFETY

• WARNING! Turn off the mains power supply before servicing or performing any maintenance.
• Maintain the light in good condition (Repairs must only be undertaken by a qualified electrician).
• Replace or repair damaged parts. Use genuine parts only, non-authorised parts may be dangerous and will invalidate the warranty.
• Ensure the light is installed correctly by these instructions.
• Only install the light on a vertical surface.
• DO NOT fix the light on any horizontal surface i.e. ceiling, or overhang.
• Ideally, the Installation should be away from flammable or combustible materials such as wood, cloth, paper etc.
• DANGER! DO NOT direct the light into a person’s eyes. This unit has a very intensive light output, which if incorrectly used could cause eye damage.
• DO NOT install the light where it is likely to be knocked or hit.
• DO NOT install in bathrooms, shower rooms, sauna or such locations.
• DO NOT install near an exhaust outlet. i.e. boiler flue, dryer outlet, etc.
• DO NOT use the light without the front glass shield fitted.

INTRODUCTION

• Mounted in die-cast powder-coated aluminium extra-slim housing with a wall bracket.
• SMD LED technology allows ultra-bright illumination whilst still keeping costs lower than traditional halogen tubes.
• Even spread of light across a 110° angle.
• Prewired with 0.75m rubberised power cable.

SPECIFICATION

ASSEMBLY

WARNING! DO NOT connect the unit to the mains power supply before installation.

INSTALLATION

• Give careful consideration to the position of the unit to ensure you obtain maximum benefit from the lighting range, and that an appropriate electrical power source can be provided.
• An approximate appropriate mounting height from the ground is 2.5m. See fig.1.
• This LED floodlight develops minimal heat and is not subject to the same mounting restrictions that apply to halogen lamps that become too hot to touch. We do however recommend that the floodlight should not be placed in cramped or restrictive positions and should be fixed at the following minimum distances between the light and any surface/object. See fig.2.
  • 500mm minimum between the top of the light and any overhead surface, or objects, i.e. ceilings, overhangs.
  • 200mm between the sides of the light and wall/surfaces.
  • 2 metres minimum between the front of the light and any object to be illuminated.
  • Fix the light to a vertical surface with appropriate fixings.
  • Ensure the lamp is connected to the mains by a qualified electrician.

MAINTENANCE

• Clean the casing externally (not the glass) with a moist cloth.
  • DO NOT use solvents or abrasives to clean the light.
• Avoid touching the glass shield as handling may reduce its serviceable life and cause the glass to crack. If necessary clean the glass shield with alcohol and a soft cloth. Undo the single screw without removing it to clean internally.
  • DO NOT use the light without the glass shield.
  • DO NOT use the light without the weather seals intact.

ENVIRONMENT PROTECTION

• Recycle unwanted materials instead of disposing of them as waste.
• All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner that is compatible with the environment.
• When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.
• REGISTER YOUR PURCHASE HERE

WEEE REGULATIONS

• Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment (WEEE).
• When the product is no longer required, it must be disposed of in an environmentally protective way.
• Contact your local solid waste authority for recycling information.
• Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and parts without prior notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call our technical team at technical@sealey.co.uk or 01284 757505.
• Important: No Liability is accepted for incorrect use of this product.
• Warranty: The guarantee is 24 months from the purchase date, proof of which is required for any claim.

CONTACT

• Sealey Group, Kempson Way,
• Suffolk Business Park,
• Bury St Edmunds,
• Suffolk. IP32 7AR
• 01284 757500
• sales@sealey.co.uk
• www.sealey.co.uk.
• © Jack Sealey Limited
• Original Language Version
• LED112.V2,
• LED113.V2,
• LED115.V2
• Issue 2 (H,2,3, F) 16/05/23
• MODEL NO’S:
  • LED112.V2,
  • LED113.V2,
  • LED115.V2

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>