TAC SW-D12N2 Sidewinder Running Boards Instruction Manual
- June 1, 2024
- TAC
Table of Contents
TAC SW-D12N2 Sidewinder Running Boards
Product Specifications
- Product Name: Sidewinder Running Board
- Part Number: SW-D12N2
- Compatibility: Fits 2019-Up Dodge RAM 1500 Quad Cab (Exclude 2019-2024 RAM 1500 Classic Quad Cab)
- Installation Time: 60-120 minutes
- Cutting: Not Required
- Drilling: Not Required
Product Usage Instructions:
Before Installation
- Remove contents from the box and verify all parts are present.
- Read instructions carefully before starting the installation.
- Assistance is recommended for the installation process.
Part List
The part list includes Front/Rear Lower Mounting Bracket x 4, Front/Rear
Upper Mounting Brackets x 4, Center Mounting Bracket x 2, and Center Support
Bracket x 2.
Torque & Tools
- Fastener Size: 6mm, 8mm, 10mm, 12mm
- Tightening Torque (ft-lbs): 7-8.5, 18-20, 35-40, 60-70
- Wrench Required: 10mm, 13mm, 16mm, 18mm
- Allen Wrench Required: 4mm, 5mm, 6mm, 8mm
Frequently Asked Questions (FAQ)
-
Q: Do I need to drill or cut during the installation of the Sidewinder Running Board?
A: No, cutting or drilling is not required for the installation of the Sidewinder Running Board. -
Q: How long does it take to install the Sidewinder Running Board?
A: The installation time is estimated to be between 60 to 120 minutes.
SIDEWINDER RUNNING BOARD
PART #: SW-D12N2
FITS:
2019-Up Dodge RAM 1500 Quad Cab
(Exclude 2019-2024 RAM 1500 Classic Quad Cab)
Torque & Tools
BEFORE INSTALLATION
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. ASSISTANCE IS RECOMMENDED.
Tool
PLEASE NOTE THAT THE FOLLOWING PICTURES ARE BASED ON THE DRIVER S IDE INSTALLATION
-
STEP 1
Start the installation under the Driver/Left side of the vehicle. Locate the front (3) factory studs along the inner side of the body panel, (Fig 1).
-
STEP 2
S elect (1) Front/Rear Upper Mounting Bracket ( #2). Attach the Mounting Bracket to the (3) factory studs with (3) 8mm x 24mm Flat Washers and (3) 8mm Nylon Lock Nuts, (Fig 2). Do not tighten hardware.
-
STEP 3
Select (1) Front/Rear Lower Mounting Bracket (#1). Attach the Lower Bracket to the short side of the Upper Bracket with (2) 8mm Hex Bolts, (4) 8mm x16mm Flat Washers and (2) 8mm Nylon Lock Nuts, (Fig 3). Do not tighten hardware.
-
STEP 4
Move to the center location, (Fig 4). Select (1) Center Support Bracket (#4). Attach the Support Bracket to the (2) lower threaded studs with (2) 8mm x 24mm Flat Washers and (2) 8mm Nylon Lock Nuts, (Fig 5).
-
STEP 5
Select (1) Center Mounting Bracket (#3) and attach to the Support Bracket and upper threaded st ud with (2) 8mm Flat Washers and (2) 8mm Nylon Lock Nuts, (Fig 6). Do not tighten hardware.
-
STEP 6
Repeat Steps 2 & 3 to attach (1) Front/Rear Upper Mounting Bracket (#2) and (1) Front/Rear Lower Mounting Bracket (#1) to the rear mounting location, (Fig 7). Do not tighten hardware.
-
STEP 7
Select the Driver/Left Running Board. NOTE: The Driver/Left Running Board will have a “12-L” on the front. IMPORTANT: Do not slide Running B oard front to back on the Brackets or damage to the finish may result. Attach the Step to the M ounting Brackets with (6) 8mm Combo Bolts, ( Fig 8). Do not tighten hardware.
-
STEP 8
Level and adjust the Running Board as necessary and fully tighten all hardware. -
STEP 9
Repeat Steps 1—8 to attach the Passenger/Right Running Board to the vehicle. -
STEP 10
Do periodic inspections to the installation to make sure that all hardware is secure and tight.
Attention
To protect your investment, do not use any type of polish or wax that may
contain abrasives that could damage the finish.
Mild soap may be used also to clean the Running Boards.
www.tacautoparts.com
Rev. 8/31/22 (NL)
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>