SEALEY AK98943 Suction Cup Instruction Manual

SEALEY AK98943 Suction Cup

Product Information

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble-free performance.

Important: Please read these instructions carefully. Note the safe operational requirements, warnings & cautions. Use the product correctly and with care for the purpose for which it is intended. Failure to do so may cause damage and/or personal injury and will invalidate the warranty. Keep these instructions safe for future use.

Product Usage Instructions

Safety

• Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this tool.
• Do not use the suction cup if any parts are damaged or missing as this may cause failure and/or personal injury.
• Before each use, check the condition of the suction cup. Examine rubber pads for excessive glaze, cuts, or roughness. If any component is worn or damaged, replace it immediately.
• Do not clean the suction cup with solvents or other harsh chemicals.
• Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
• Use in a suitable work area. Keep the area free from unrelated materials and ensure that there is adequate lighting.
• Always wear approved eye, face, and hand protection when using the suction cup.
• Remove ill-fitting clothing, ties, watches, rings, and other loose jewelry, and contain/tie back long hair.
• Maintain correct balance and footing. Do not overreach, ensure the floor is not slippery, and wear non-slip footwear.
• Keep children and unauthorised persons away from the working area.
• Ensure the workpiece is secure before attaching and using the suction cup.
• Ensure that the surface to which the suction cup is to be attached is non-porous, clean, dry, and free from oil and grease.
• Do not exceed the maximum pull capacity of the suction cup.
• Do not use the suction cup for any purpose other than that for which it is designed.
• Do not use the suction cup when you are tired or under the influence of alcohol, drugs, or intoxicating medication.
• When not in use, store in a safe, dry, childproof location.
• Do not use any sharp object to loosen the suction cup as it may damage the rubber and prevent the tool from creating suction.
• Do not attempt to attach the suction cup to a person as severe bruising and/or damage to internal organs can occur.
• Do not allow anything to interfere with the free movement of the plunger while the suction cup is attached to a surface. Keep fingers clear of the suction release tag during use.
• Do not allow anything else to touch the release tab while lifting e.g., other lifting gear or adjacent fixtures and fittings.

Introduction
Twin profiled rubber suction cups designed for strength and reliability. Ideal for windscreen installation and glass transportation. Also suitable for other nonporous flat surfaces such as sheet metal and tiles.

Frequently Asked Questions (FAQ)

• Q: Can I use this suction cup on plastic surfaces?
  A: The tool may not be as effective on plastic surfaces as it is on nonporous flat surfaces such as glass, sheet metal, and tiles.  It’s recommended to test on a small area before full application.

• Q: How should I store the suction cup when not in use?
  A: Store the suction cup in a safe, dry, childproof location away from any sharp objects that could damage the rubber pads. Ensure it is easily accessible for future use but out of reach of children.

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble-free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

SAFETY

• WARNING! Ensure Health & Safety, local authority and general workshop practice regulations are adhered to when using this tool.
• DO NOT use the suction cup if any parts are damaged or missing as this may cause failure and/or personal injury.
• Before each use, check the condition of the suction cup.
• Examine rubber pads for excessive glaze, cuts or roughness. If any component is worn or damaged replace it immediately.
• DO NOT clean the suction cup with solvents or other harsh chemicals.
• Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
• Use in a suitable work area. Keep the area free from unrelated materials and ensure that there is adequate lighting.
• WARNING! Always wear approved eye, face and hand protection when using the suction cup.
• Remove ill-fitting clothing. Remove ties, watches, rings, and other loose jewellery and contain and/or tie back long hair.
• Maintain correct balance and footing. DO NOT overreach, ensure the floor is not slippery, and wear non-slip footwear.
• Keep children and unauthorised persons away from the working area.
• Ensure the workpiece is secure before attaching and using the suction cup.
• WARNING! Ensure that the surface to which the suction cup is to be attached is non-porous, clean, dry and free from oil and grease.
• DO NOT exceed the maximum pull capacity of the suction cup.
• DO NOT use the suction cup for any purpose other than that for which it is designed.
• DO NOT use the suction cup when you are tired or under the influence of alcohol, drugs or intoxicating medication.
• When not in use, store in a safe, dry, childproof location.
• DO NOT use any sharp object to loosen the suction cup as it may damage the rubber and prevent the tool from creating suction.
• DO NOT attempt to attach the suction cup to a person as severe bruising and/or damage to internal organs can occur.
• DO NOT allow anything to interfere with the free movement of the plunger whilst the suction cup is attached to a surface.
• Keep your fingers clear of the suction release tag during use.
• DO NOT allow anything else to touch the release tab whilst in the process of lifting e.g. other lifting gear or adjacent fixtures and fittings.

INTRODUCTION

Twin profiled rubber suction cups are designed for strength and reliability. Ideal for windscreen installation and glass transportation. Also suitable for other nonporous flat surfaces such as sheet metal and tiles.

SPECIFICATION

• Model No: …………………………………………………. AK98943
• Cup Diameter: ……………………………………………..Ø150mm
• Maximum Lift Capacity: …………………….. 30kg (Horizontal)

OPERATION

• WARNING! Ensure that you read, understand and apply Section 1 safety instructions.
  The suction cup is designed to work best on float glass at a room temperature of 20ºC. Cold temperatures, humidity and other surface contamination may reduce the holding capacity of the tool. The tool may not be as effective on other sheet materials such as plastic and metal. Moisture and other contaminants will also reduce the slip resistance of the cup.

• WARNING! This is a hand tool and must not be used in conjunction with a crane or any other lifting device.

1. Ensure that the workpiece to be moved is clean, dry and free from oil and grease.

2. Remove the protective cover from the suction cup.

3. Holding the handle, firmly push the suction cup onto the material and hold it there under pressure.

4. With your other hand, pump the plunger until it recedes into the barrel and the red line disappears from view. The suction cup should now be firmly attached and ready for use.

5. Always keep the plunger in view during moving/lifting. Should the plunger begin to rise and the red line reappear, this indicates a loss of suction and you should immediately put down the load.

6. Check that the suction cup and surface of the material are clean and free from any foreign bodies or imperfections. When satisfied, reattach the suction cup as previously described.
   NOTE: The suction cup is designed for lifting, carrying and holding objects for a short period only. If circumstances cause an object to be held for longer than expected, the grip must be checked frequently concerning the plunger position and the visibility of the red line.

7. Only release the suction cup when the load has been set down. To release the suction cup from the surface to which it is attached, lift the release tag at the side of the cup.

   • DO NOT use any sharp object to loosen the suction cup as it may damage the rubber and prevent the tool from creating suction.

8. Refit the protective cover onto the suction cup and store it in a clean, dry, childproof location.

MAINTENANCE

1. Check condition of suction cup regularly, if damaged replace using genuine parts only.
2. Always keep suction cup clean and free of oil and grease. Clean regularly with a non-aggressive cleaner.
3. In order to preserve elasticity, do not expose rubber pads to sunlight over an extended period.

ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner that is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and parts without prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
sales@sealey.co.uk
www.sealey.co.uk

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>