asaLITE ASAL0281 LED Ceiling Lamp Light User Manual
- June 1, 2024
- asaLITE
Table of Contents
asaLITE ASAL0281 LED Ceiling Lamp Light
Product Specifications
- Product code: ASAL0281
- Product size: 330x63mm
- Network: AC220-240V 50/60Hz
- Power: 24W
- Lumen: 2470
- Kelvin: 4000K
- Warranty: 2 years
- IP Protection: 44
- Dimmable: No
- Lighting angle: 44 degrees
- EAN code: 5999565665999
Installation Instructions:
- POWER OFF : Turn the power off before installation!
- Remove the plastic frame and the screws. Open up the lampshade!
- Drill holes according to the installation position. Plug the cable through the hole!
- Install the screws!
- Connect the wires!
- Put back the plastic frame!
- POWER ON : You can turn on the power!
Microwave Sensor Function:
SENSOR TEST:
Note: when testing in daylight, please turn the LUX knob to 2000lux, otherwise the sensor lamp could not work!
Important Safety Instructions:
It is recommended to seek assistance from an authorized electrician for installation.
Maintenance :
Clean and inspect every 6 months! Wipe the cover with a damp soft cloth then a dry cloth. Do not wipe the electric components. Do not use ethanol or gasoline for cleaning.
Additional Information:
The product is certified to comply with European regulations and guidelines. For indoor use only.
FAQ
- What’s included in the box?
- The box contains 1x Ceiling lamp, 3x Screws, 3x Dowels, and 1x user manual.
Importer Information:
Importer: www.asalite.com Asalite. All rights reserved.
Asalite LED Ceiling Lamp IP44 + M/V Sensor
Product code
|
Product size
|
Network
|
Power
|
Lumen
|
Kelvin
|
Warranty (year)
|
IP
Protection
|
Dimmable
|
Lighting angle
|
EAN code
---|---|---|---|---|---|---|---|---|---|---
ASAL0281
|
ф330x63mm
|
AC220-240V 50/60Hz
|
24W
|
2470
|
4000K
|
2
|
44
|
NO
|
120°
|
5999565665999
INSTALLATION
- Turn the power off before installation!
- Remove the plastic frame and the screws. Open up the lampshade!
- Drill holes according to the installation position. Plug the cable through the hole!
- Install the screws!
- Connect the wires!
- Put back the plastic frame!
- You can turn on the power!
MICROWAVE SENSOR FUNCTION
The product has a microwave LED sensor with high-frequency electromagnetic waves (5.8GHz) and an integrated circuit, SMD LED.
-
Can identify day and night: It can work in the daytime and at night when it is adjusted to the “sun” position (max). It can work in the ambient light less than 3LUX when it is adjusted on the “3” position (min). As for the adjustment pattern, please refer to the testing pattern.
-
Detection range selectable: It can be adjusted according to using location.
The detection distance of low sensitivity could be only 2m and high sensitivity could be 16m which fits for large room. -
Time-Delay is added continually: When it receives the second induction signal within the first induction, it will restart to time from the moment.
-
Time–Delay is adjustable. It can be set according to the consumer’s desire. The minimum time is 6 seconds. The maximum is 30min.
Connecting to other lamps:
IMPORTANT SAFETY INSTRUCTIONS!
- Install, check and repair should be done by an electrician!
- If the external flexible cable or cord of this luminary is damaged, it can only be replaced by a specialist to avoid danger!
- Take out all the packaging before installation!
- Do not exceed the rated voltage range!
- Do not install on an unstable wall!
- In case the product works abnormally, cut off the power and contact the seller!
- Always turn off the power before starting installation.
- In some countries, electrical installation work may only be carried out by an authorized electrician.
Asalite Lighting Kft. certifies that our product is manufactured in accordance with European regulations and guidelines
SENSOR TEST
- Turn the LUX knob clockwise on the maximum (sun). Turn the SENS knob clockwise on the maximum (+). Turn the TIME knob anti-clockwise on the minimum (10S),
- When you switch on the power, the lamp will be on at once, and 10sec±3sec later the lamp will be off automatically. Then if the sensor receives an induction signal again, it can work normally.
- When the sensor receives the second induction signal within the first induction, it will restart to time from the moment.
- Turn the LUX knob anti-clockwise on the minimum (3). If the ambient light is less than 3LUX (darkness), the inductor load could work when it receives an induction signal.
- Note : when testing in daylight, please turn the LUX knob to 2000lux, otherwise the sensor lamp could not work!
IMPORTANT INFORMATION!
- Keep the purchase receipt for the warranty.
- We do not offer a free warranty for wrong voltage usage and incorrect installation. Self-repair or modify. Usage of incorrect accessories, tools. Transportation or other accident damage.
- The light source of this product is non-changeable light diodes (LED). Do not disassemble the product, as the light diodes can cause damage to the eyes.
MAINTENANCE
Clean and inspect every 6 months! Wipe the cover with a damp soft cloth then dry cloth! Do not wipe the electric components! Do not wipe with ethanol or gasoline to avoid damage!
CAUTION!
- Improper installation of the product may result in a risk of electric shock!
WHAT’S IN THE BOX
- 1x Ceiling lamp
- 3x Screws, 3x Dowels
- 1x User manual
IMPORTER
Asalite Lighting Kft.
- H-4033 Debrecen Vak Bottyán utca 22/A
Made in : P.R.C. Copyright © 2024
Asalite All rights reserved.