SYNC EV EVCM221310-01 Mode 2 EV Charger User Guide
- June 1, 2024
- SYNC EV
Table of Contents
SYNC EV EVCM221310-01 Mode 2 EV Charger User Guide
This BG SyncEV Mode 2 charger is intended for use with electric and hybrid vehicles. Please read and use in accordance with these safety instructions. Please retain instructions for reference, or scan the QR code.
SAFETY INSTRUCTIONS
Always inspect before use, do not use if the Electric Vehicle Supply Equipment (EVSE) plug, or cable is damaged. Do not use with an extension lead or adaptor. Connect the charging cable to a correctly functioning and fixed socket outlet marked with ‘BS1363/EV’. The user is responsible for any personal injury or vehicle or property damage arising from inappropriate use. Do not use subject the product to corrosive liquid, flammable dust, or in strong corrosive environments. Use and store within the service conditions stated in the Technical data. The storage or use shall not exceed the service condition stated as above. Misuse such as dropping, immersion may cause the risk or damage.
Do not immerse the product in the water, protect the plug and cable from moisture. Do not use in a corrosive liquid, flammable dust, or strong corrosive environment.
OPERATING INSTRUCTIONS & INDICATOR STATUS
- Insert 3-pin plug into wall socket (and switch on) – Charger starts self test mode, LED will flash green & red alternatively x3 times. Approximately 5 seconds. After test Green indicator should appear ‘Ready’, if Red check fault guide.
- Connect to EV – the charger will then start communication with the car, indicator will flash Green fast.
- Charging – Green indicator slow pulse. Once charged indicator will flash Green fast.
- To end charging remove disconnect (turn off) from wall socket, and remove charger from EV.
Action| Indicator Status| Remark
---|---|---
Connect to wall socket| Green & Red alternate flash x3| Self-test procedure (approx. 5s)
Ready| Green On|
Connect to EV| Green fast flash| Communication test
Charging| Green pulse|
Fault| Red| See Fault Guide
TECHNICAL
- Voltage: 230V~
- Output : 2.3kW Max
- Frequency: 50Hz
- Power supply system: TN-S system
- Residual Operating Current: n: 30mA, 6mA DC
- Operating Temperature: -25~+45 deg C
- Relative humidity: MAX 75%/40℃
- IP Rating (Function box): IP65
- Altitude: up to 2000m
- Standards: BS EN 62752, BS EN 61851-1
FAULT GUIDE & TROUBLE SHOOTING
| Fault | Indicator Status | Remark |
|---|---|---|
| PEN or Earth Fault | Red ON | Lack of earth connection at wall socket. |
| CP Error | Red flash x 2 > off 3 secs | Charging cable fault / CP voltage |
abnormal
Voltage Fault| Red flash x 3 > off 3 secs| Input voltage out of tolerance
(184VAC to 260VAC)
OCP| Red flash x 4 > off 3 secs| Overload, current set too high. Check EV
settings. Max 10A
Leakage| Red flash x 5 > off 3 secs| Earth fault. Turn off power and check for
damage to the cable
OTP| Red flash x 6 > off 3 secs| Over temperature (>85 C)Turn off power for
30min and allow to cool.
SCP| Red flash x 7 > off 3 secs| Charging cable fault
D Fault| Red flash x 8 > off 3 secs| Charging cable fault
Welding| Red flash x 9 > off 3 secs| Charging cable fault
Measurement Fault| Red flash x 10 > off 3 secs| Failed EV communication.
Repeat connection procedure
To reset and clear the fault follow the instructions, Unplug charging cable from the vehicle. Unplug (or turn off) charging cable from the wall socket. Keep unplugged for 30 seconds. Repeat connection process.
If the faults are not reset, the charging cable may be fault. Please contact
the retailer, or BG SyncEV via our helpdesk support team –
email : support@syncev.co.uk, or our
website www.syncev.co.uk
CARE
SyncEV recommend the use of a soft dry or slightly damp cloth periodically to
clean the cable and charger body. Do not use cleaning agents
BATCH CODE EXPLANATION
yyWxx Manufacturing date code, year of manufacture (yy) and week of manufacture (Wxx
ENVIRONMENTAL PROTECTION
This symbol is known as the “Crossed-out Wheelie Bin Symbol”. When this symbol is marked on a product or battery, it means that it should not be disposed of with your general household waste. Some chemicals contained within electrical/ electronic products or batteries can be harmful to health and the environment. Only dispose of electrical/electronic/ battery items in separate collection schemes, which cater for the recovery and recycling of materials contained within. Your co-operation is vital to ensure the success of these schemes and for the protection of the environment.
ADDRESS / HELPINE
Luceco PLC: Stafford Park 1
Telford TF3 3BD: ENGLAND
(EU) Luceco SE: C/ Bobinadora 1-5
08302 Mataro: SPAIN
If you have further technical assistance you can get in touch with our
Technical Helpline on: +44 (0)3300 249 279 /
support@syncev.co.uk
www.syncev.co.uk.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>