SC AUTOSPORTS M1124M-3704010 One Button Start Switch Instruction Manual

M1124M-3704010 One Button Start Switch

“`html

Specifications:

• Product Name: PS-Agility
• Model Number: M1124M-3704010
• Category: Host / smart key / NFC induction antenna / one-button
  start button

Product Information:

List of Complete Machine of Products

Product Size Diagram:

1. Control module
2. One NFC receiving antenna
3. A start switch

Connection Plug-in Definition:

Product Technical Parameters:

Product Usage Instructions:

Function Brief Introduction:

FAQ:

Question: How do I start the vehicle using the one-button start

switch?

Answer: After the breathing light is on, press the switch to
start the vehicle. The button indicator light should remain on.

“`

One-button start switch assembly specification document

Document status [] rough draft [] Official release [] Modifying Reading personnel

edition

V1.6

author

Nicholas Teo

date of issue

2024-6-12

security

common

classification

Members of the project team

1

Ingenuity such as new, manufacturing future Nushine Innovation, Intelligent Manufacture

1. Product name: PS-Agility

2. Model number:M1124M-3704010

Category: Host / smart key / NFC induction antenna / one-button

start button

2. List of complete machine of products

order number

name

quant ity

graphic

remarks

control

1

1

module

cabinet

NFC

2

receiving 1

antenna

Start the

3 switch with 1

one key

NFC Key

4

2

Card

5

screw

2

instructio

6

1

ns

M4*12 /

receiving antenna Card swiping range is 3cm
With backlight switch
Mini card: Magenta mother card Blue card With nuts
/

2

Ingenuity such as new, manufacturing future Nushine Innovation, Intelligent Manufacture

3Product size diagram 1control module

2 product size accessories one NFC receiving antenna 3 the product size accessories a start switch

4NFC card

3

Ingenuity such as new, manufacturing future Nushine Innovation, Intelligent Manufacture

front

rever

4Connection plug-in definition
5.1 Definition of the controller connector

1

9

10

18

Main connector model number:

pin foot position

definition

1

power input

2

3

12V+ output

4

12V 200mA

5

6V NFC

6

NFC PDOWN

7

NFC IRQ

8

The RS232 power supply switch

9

NFC RS232_TX

10

GND

11

Start power with one key

12

Start the indicator light with

13

Start the breathing light with

14

Key detection

15

CAN_H

16

CAN_L

17

GND

18

NFC RS232_RX

MX23A18NF1 remarks
12V 5A
obligate

4

Ingenuity such as new, manufacturing future Nushine Innovation, Intelligent Manufacture

5.2 Definition of the NFC antenna connector

6

18

7

9

5

10

Main connector model number:

pin foot position

definition

5

NFC 6V Power supply

7

NFC IRQ Interrupt the input

6

NFC PDOWN Power drop reset

10

GND

9

NFC TX

18

NFC RX

5.3 Definition of one-button start switch connector

JST06RT remarks
NFC antenna

11

14

Main connector model number:

pin foot position

definition

11

Start power with one key

12

pilot lamp

13

breathing light

14

Key detection

JST04TR remarks

4. Product technical parameters:

order numbe
r

essential parameter

explain

5

Ingenuity such as new, manufacturing future Nushine Innovation, Intelligent Manufacture

1 working voltage

DC 7V 16V

2 working current

25mA

3 Standby current

operating 4
temperature range
Storage 5
temperature range

6

way to install

3mA -3080 -4085 screw fixing

7

CAN

The CAN communication module

5. Product function brief introduction:

orde

r

work

numb pattern

explain

Function number

er

NFC Brush the card in the

1

FS01/FS03

swing designated area, and start the

6

Ingenuity such as new, manufacturing future Nushine Innovation, Intelligent Manufacture

card

switch breathing light on. Use the administrator (master

card) card to enter the card

learning mode.

Start switch After the

breathing light is on, press the

switch to start the vehicle, and

One key the button indicator light is

2

FS02

start always on.

After the vehicle starts,

press the switch to close the

vehicle.

CAN

communica The upper and down power is

3

tion controlled by connecting with the FS04FS05

(Reserved reference bus.

)

Vi. Product function Description: 1. Press the button to start after NFC authorization [Function No.] FS01

7

Ingenuity such as new, manufacturing future Nushine Innovation, Intelligent Manufacture

[precondition] Power supply gear is in OFF gear (i. e. foot 4 does not output 12V) [Trigger conditions] At least one NFC key card was detected in the swipe area and moved close to the swipe area for about 1 second. [movement] Turn on the blue breathing light after swiping the card After pressing the switch, the module sends an external ACC status message Power on the vehicle, the start switch green indicator light is always on

2. Close the button [Function No.] FS02 [precondition] The power supply gear is in the ACC gear Module detects vehicle speed of 2 km/h (vehicle speed resolved by CAN message) [Trigger conditions] Press the switch button

8

Ingenuity such as new, manufacturing future Nushine Innovation, Intelligent Manufacture

[movement] The module disconnects the ACC signal The Module stops issuing the ACC status message Power on the vehicle, and the start switch indicator light is off

3.NFC card learning [Function No.] FS03 3.1 Master card learning
Under the power state, the encrypted NFC card is placed in the swiping area, and the switch is pressed for 6 times continuously within 10s to trigger the reverse learning card mechanism (mother card learning mode). The green indicator light changes from unbright to always bright, representing the success of the learning card. 3.2 Subcard learning [precondition] 1 mother card and 1 encrypted empty card The vehicle is in an OFF state [Trigger conditions]

9

Ingenuity such as new, manufacturing future Nushine Innovation, Intelligent Manufacture

At least one master card was detected in the swipe area and remove the master card when the blue breathing light is on [movement] Enter card mode Press the switch for 3 seconds within 15 seconds, and the blue breathing light is always on. Put the encrypted empty card in the 10S. If the card is successful, start the switch green indicator light to flash 2 times. There are only five subcards at the same time.

[remarks] 1) If no card or second card is detected within 10 seconds after successfully triggering the card mode, exit the card mode. 2) If the module is damaged, the module must be replaced first, and then use a new card to match the card once the card matches the module, it can only be matched with the current module invalid card without feedback 3 Child mother cards are encryption cards, child mother card has the function of up and down power. 4 The mother card is unique. After the mother card is lost and the mother card is lost, the original mother card fails. 5) Non-manufacturer encryption cards are invalid cards.

10

Ingenuity such as new, manufacturing future Nushine Innovation, Intelligent Manufacture

FCC Statement Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment .
Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: –Reorient or relocate the receiving antenna. –Increase the separation between the equipment and receiver. –Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. –Consult the dealer or an experienced radio/TV technician for help.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>