TAC 3S-F112T Side Steps Running Boards Instruction Manual
- June 1, 2024
- TAC
Table of Contents
TAC 3S-F112T Side Steps Running Boards
Product Information
3 SIDE BAR 2015-2024 FORD F150 & 2022-2024 F150 Lightning EV SUPERCREW CAB
2017-2024 F250/350/450/550 SUPER DUTY CREW CAB PART# 3S-F112T
Specifications
- Material: Steel
- Finish: Black Powder Coat
- Compatibility: 2015-2024 Ford F150, 2022-2024 F150 Lightning EV SuperCrew Cab, 2017-2024 F250/350/450/550 Super Duty Crew Cab
Product Usage Instructions
Parts List
- 1 Driver/left Sidebar
- 1 Passenger/right Sidebar
- 2 Driver/left front-passenger/right rear Brackets
Installation Procedure
- REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT.
- READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. ASSISTANCE IS RECOMMENDED.
- Start the installation under the driver side of the vehicle.
Frequently Asked Questions (FAQ)
-
Q: Can these side bars be installed on a different vehicle model?
A: These side bars are specifically designed for the mentioned Ford models. Installation on other models may not be compatible. -
Q: How should I maintain these side bars?
A: Periodic inspections are recommended to ensure all hardware is secure and tight. Clean with a mild detergent and water solution to maintain appearance.
INSTALLATION INSTRUCTIONS
3″ SIDE BAR
2015-2024 FORD F150 & 2022-2024 F150 Lightning EV SUPERCREW CAB 2017-2024
F250/350/450/550 SUPER DUTY CREW CAB
PART# 3S-F112T
90-DEGREE BENT END SIDEBARS
2015-2024 FORD F150 & 2022-2024 F150 Lightning EV SUPER CREW CAB 2017-2024
F250-350 SUPER DUTY CREW CAB
PARTS LIST
| 1 | Driver/left Sidebar | 4 | 1/2″ x 2” Hex Bolts |
|---|---|---|---|
| 1 | Passenger/right Sidebar | 4 | 1/2” x 1-1/4” OD x 3/32” Flat Washers |
| 2 | Driver/left front-passenger/right rear Brackets | 4 | 1/2” Lock Washers |
| 2 | Passenger/right front-driver/left rear Brackets | 2 | 8-1.25mm x 25mm Hex |
Bolts
2| Center Brackets (use for driver or passenger side)| 20| 8mm x 24mm OD x 2mm
Washers
18| 8mm Plastic Washers| 2| 8mm Lock Washers
| | 18| 8-1.25mm Nylon Lock Nuts
PROCEDURE
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS
CAREFULLY BEFORE STARTING INSTALLATION. ASSISTANCE IS RECOMMENDED.
- Start the installation under the driver side of the vehicle. Locate the front, center and rear factory running board mounting locations along the inner side of the body, (Figure 1).
- Slide (1) Plastic Washer over each factory mounting stud in the body panel, (Figures 2 & 3). IMPORTANT: The Plastic Washers are designed to prevent corrosion between the aluminum body panel and the steel mounting brackets. Do not install the Brackets without the Plastic Washers.
- Select (1) driver side front Mounting Bracket. NOTE: Same bracket is used for the passenger side rear installation. Attach the Mounting Bracket to the (3) factory studs with (3) 8mm Flat Washers and (3) 8mm Nylon Lock Nuts, (Figure 4). Snug but do not fully tighten the hardware.
- Select (1) Center Bracket. Repeat Steps 1—3 to install the driver side center Bracket, (Figure 5). NOTE: Center Bracket is the same, driver side and passenger side.
- Repeat Steps 1—3 to install the driver side rear Bracket, (Figure 6). NOTE: Same Bracket is used for the passenger side front installation.
- Select the driver/left Sidebar. With assistance, position the Sidebar up to the front and rear Mounting Brackets. Attach the Sidebar to the Mounting Brackets with the included (2) 1/2” x 2” Hex Bolts, (2) 1/2” Lock Washers, and (2) 1/2” Flat Washers, (Figure 6). Leave hardware loose at this time.
- Line up the threaded insert in the bottom of the Sidebar with the center Bracket. Attach the Sidebar to the Bracket with (1) 8mm x 25mm Hex Bolt, (1) 8mm Lock Washer and (1) 8mm Flat Washer, (Figure 7). Leave hardware loose at this time.
- Level and adjust the Sidebar and tighten all hardware.
- Repeat Steps 1—8 to install the passenger/right Sidebar.
- Do periodic inspections to the installation to make sure that all hardware is secure and tight.
To protect your investment , wax this product after installing. Regular
waxing is recommended to add a protective layer over the finish. Do not use
any type of polish or wax that may contain abrasives that could damage the
finish.
For stainless steel: Aluminum polish may be used to polish small
scratches and scuffs on the finish. Mild soap may be used also to clean the
Sidebar.
For gloss black finishes: Mild soap may be used to clean the Sidebar.
Driver/left side installation pictured
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>