FISHER PAYKEL DW24UT2I2 Built In Dishwasher Installation Guide

DW24UT2I2 Built In Dishwasher

“`html

Specifications:

• Model: DW24UT2I2 & DW24UT4I2
• Type: Built-under dishwasher
• Designed for: Indoor use

Product Usage Instructions:

Safety Precautions:

Before using the dishwasher, ensure to follow these important
safety precautions:

• Do not operate the appliance if it is damaged or
  malfunctioning.

• Avoid storing flammable materials near the dishwasher.

• Connect the dishwasher to a properly rated power supply
  circuit.

Installation Guidelines:

Proper installation is crucial for the efficient and safe
operation of the dishwasher. Follow these installation
guidelines:

1. Ensure all water connections are turned off before
   installation.

2. Make sure the dishwasher is placed between cabinetry to prevent
   instability.

3. Use only new hoses supplied with the dishwasher for
   connections.

4. Keep the dishwasher upright during relocation to avoid water
   spillage.

Maintenance and Servicing:

Regular maintenance and servicing will prolong the life of your
dishwasher. Follow these tips:

• Do not attempt to repair or replace any part unless recommended
  in the guide.

• For servicing, contact a Fisher & Paykel trained service
  technician.

Frequently Asked Questions (FAQ):

Q: Can I use an extension cord to connect the dishwasher to a

power supply?

A: No, it is advised not to use an extension cord or
multi-socket outlet box for connecting the dishwasher to the power
supply. It should be connected directly to a properly rated power
supply circuit.

Q: What should I do if the dishwasher is damaged or missing

parts?

A: Do not operate a damaged appliance. Contact a qualified
service technician for repair or replacement of any missing or
broken parts.

Q: Can I install the dishwasher outdoors?

A: No, the dishwasher is designed for indoor use only. Do not
expose it to freezing temperatures or outdoor weather
conditions.

“`

BUILT-UNDER DISHWASHER
INTEGRATED DW24UT2I2 & DW24UT4I2 models
INSTALLATION GUIDE US CA
592981C 12.23

SAFETY AND WARNINGS

WARNING!
Electric Shock Hazard
Failure to follow this advice may result in electrical shock or death.
· This appliance must be earthed. This appliance has a cord with an equipment- earthing conductor and an earthing plug. The plug must be plugged into an appropriate outlet that is installed and earthed in accordance with all local regulations.
· WARNING ­ Improper connection of the
equipment-earthing conductor can result in a risk of electric shock. Check with a qualified electrician or service technician if you are unsure if the appliance is properly earthed.
· Do not modify the power supply plug provided with the appliance. If a different outlet is required have it installed by a qualified electrician. Do not use an extension cord, adapter plug or multi-box.

WARNING! Cut Hazard Failure to use caution could result in injury. · Take care ­ panel edges are sharp.
WARNING! Weight Hazard Failure to follow this advice may result in damage or personal injury. · Do not attempt to lift this product unassisted.

3

SAFETY AND WARNINGS

WARNING!
To reduce the risk of fire, injury to persons or damage when using the appliance, follow the important safety instructions listed below. Read all the guidance before using the appliance.
Servicing
z Do not repair or replace any part of the appliance unless specifically recommended in this guide. All other servicing should be undertaken by a Fisher & Paykel trained and supported service technician or qualified person.
Installation
z Ensure all water connections are turned OFF. It is the responsibility of the plumber and electrician to ensure that each installation complies with all Codes and Regulations.
z The dishwasher MUST be installed to allow for future removal from the enclosure if service is required.
z The switched power outlet must be outside the dishwasher cavity, so that it is accessible after installation.
z This dishwasher is manufactured for indoor use only. z Care should be taken when the appliance is installed or removed to reduce the likelihood
of damage to the power supply cord and hoses. z If the dishwasher is to be relocated from one installation to another it must be kept
upright to avoid damage from water spillage. z Make sure only new hoses are used for connection (supplied with the dishwasher). Old
hoses should not be reused. z Failure to install the dishwasher correctly could invalidate any warranty or liability claims. z Ensure the dishwasher is placed between cabinetry. Failure to do so may result in an
unstable product, which may cause damage or injury. z Do not operate this appliance if it is damaged, malfunctioning, partially disassembled or
has missing or broken parts, including a damaged power supply cord or plug. z Do not store or use petrol, or other flammable vapours and liquids in the vicinity of
the dishwasher. z Connect to a properly rated, protected and sized power supply circuit to avoid
electrical overload. z Make sure that the power supply cord is located so that it will not be stepped on, tripped
over or otherwise subject to damage or stress. z Do not install or store the dishwasher where it will be exposed to temperatures below
freezing or exposed to weather. z Do not use an extension cord or a portable electrical outlet device (e.g. multi-socket
outlet box) to connect the dishwasher to the power supply. z This appliance must be earthed. In the event of a malfunction or breakdown, earthing will
reduce the risk of electric shock by providing a path of least resistance for electric current. z This appliance is equipped with a cord having an equipment-earthing conductor and an
earthing plug. The plug must be plugged into an appropriate outlet that is installed and earthed in accordance with all local codes and ordinances. z EARTHING INSTRUCTIONS – This appliance must be connected to a earthed metal, permanent wiring system, or an equipment-earthing conductor must be run with the circuit conductors and connected to the equipment-earthing terminal or lead on the appliance. z Ensure the product is not plugged in when fitting custom panels. z Installation of custom panels requires basic mechanical and electrical skills. z Installation must comply with your local building and electricity regulations.
4

z Failure to install the custom panels correctly could invalidate any warranty or liability claims.
z Installation of this dishwasher requires basic mechanical and electrical skills. z Be sure to leave these Instructions with the Customer. z Installation must comply with your local building and electricity regulations. z At the completion of the dishwasher installation, the Installer must perform the
Final Checklist. z Remove all packaging materials supplied with the dishwasher. z If the product is installed in a motor vehicle, boat or similar mobile facility, you must bring
the vehicle, boat or mobile facility containing the product to the service shop at your expense or pay the service technician’s travel to the location of the product. z This appliance is fitted with a water heating feature and intended for connection to a hot water supply.
SAVE THESE INSTRUCTIONS
The models shown in this installation guide may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please go to our website www.fisherpaykel.com or contact your local Fisher & Paykel dealer.

COMPONENTS REQUIRED

z Keep all packing materials until the unit has been inspected. z Inspect the product to ensure there is no shipping damage. If any damage is detected
contact the dealer or retailer you bought the product from to report the damage. z Fisher & Paykel is not responsible for shipping damage.
Supplied

PARTS
Components for new installation only (available in hardware stores)

Spacers (4)

Moisture protection tape (1)

Drain hose support (1)

Sound seal (1)

Air gap for drain hose (use only if required)

Wate tee for house plumbing (use only if requried)

3/4″ (16mm) Strain relief for electrical connection

Screw-type hose clamps

4 x 25mm screws (4)

4 x 13mm screws (5)

Door panel template (1)

Exit vent (1)

Hot water line with ferrule and compression nut – min 3/8″ (9.5mm) copper tubing or flexible braided hose

Electrical cable or Power cord kit – 5′ 4″ (163cm) or 7′ 9″ (236cm) long depending on your installation

Hand shut-off valve (recommended)

Sliding bracket (1)

3.5 x 11mm screws (2)

Required (not supplied)

3.9 x 38mm screws (6)

UL-listed wire nuts (3)

Thread seal tape (1)

3/4″ (19mm) Elbow 90° (1)

WARNING!
Ensure the power cord and connections comply with the National Electrical Code, Section 422 and/or local codes and ordinances. Maximum power cord length is 6 feet. A power Cord Kit is available for purchase from an authorized Fisher & Paykel appliances dealer.
Check the house wiring. If it is not 2-wire with ground, a ground must be provided by the installer. If the house wiring is aluminum, use UL-Listed anti-oxidant compound and aluminum-to-copper connectors.
5

Not supplied

COMPONENTS REQUIRED
TOOLS
Supplied

Powered driver

Cross-head screw driver

Flat-head screw driver

Box cutter

Phillips head key

Allen Key 1/4″ (6mm) and 3/16″ (4mm)

Nutdriver 1/4″ (6.35mm) and 5/16″ (7.94mm)

Adjustable wrench 6″ (152.4mm)

Measuring tape

Safety glasses

Flashlight

Gloves

Bucket – for flushing the line

Tubing cutter

Hole saw set

Level

6

Carpenters square

b c
k PLAN
i a
j FRONT

PRODUCT DIMENSIONS

ISO

h

e

PRODUCT DIMENSIONS

INCH

MM

A Overall height*

33 3/4 ­36 1/8

857­917

B Overall width**

23 7/16

597

C Overall depth**

21 13/16

554

D Height of chassis

33 3/4

857

E Depth of chassis

20 1/2

521

F Height of feet*

0­2 3/8

0­60

G Depth of toe kick recess

4 9/16

116

H Depth of inner door**

1 5/16

33

I Height from top of chassis to bottom of inner door

28 5/16

719

J Height from to bottom of inner door to floor*

5 7/16 ­7 13/16

138­198

K Minimum depth of door opening**

26 5/8

676

*depending on adjustment of levelling feet

d

**excluding custom panel and handle

g

f

PROFILE

Actual product dimensions may vary by 1/16″ (2mm) 7

CUSTOM PANEL DIMENSIONS

Material specifications
z Maximum weight of door panels must not exceed 22lb (including handle) z The panel should be adequately sealed to withstand moisture (122°F
(50°C) 80% RH). The back and sides of the panel should be completely sealed with a waterproof vapour barrier, such as polyurethane, to prevent damage. z Installation outside these specifications may result in condensation on cabinetry surfaces.

c

b

Toe kick considerations

z Depending on the desired toe kick recess depth and door panel

extension, the toe kick panel height may need to be adjusted to allow

adequate door swing.

a

c e
a
f d

ISO

PROFILE

CUSTOM PANEL CONSIDERATIONS
A Minimum height of custom door panel for full coverage of the inner door
B Minimum door panel width C Door panel depth D Distance from base of door panel to floor E Minimum clearance between top of door panel and benchtop F Maximum overhang of Custom Panel to bottom of inner door

INCH

MM

28 1/8
23 7/16 5/8­1
2 3/4­7 7/8 1/16
2 3/4

714
596 16­25 70­200
2 70

Weight of door panel (including handle)

9­20lb

4­9kg

8

DIMENSIONS
C

CABINETRY

CLEARANCES

A d
B

Connections can be located in an adjacent cabinet on either side of the dishwasher***

B PLAN

ISOMETRIC

CABINETRY DIMENSIONS

INCH

MM

A Minimum inside height*

33 3/4

857

B Minimum inside width

23 5/8

600

C Minimum overall depth**

22 13/16

580

D Height of toe kick area

2 3/4­7 7/8

70­200

depending on adjustment of levelling feet including 3/4″ (19mm) door panels on adjacent cabinetry For more information on service requirements, refer to ‘Plumbing & electrical considerations’ and ‘Cabinetry preparation’.

CABINETRY CLEARANCES
A Minimum clearance to adjacent cupboard door B Minimum clearance to corner cupboard

A

INCH

MM

1/16

2

1/2

13

9

PLUMBING & ELECTRICAL CONSIDERATIONS
Hose and cord lengths z Your services can be installed to either the left-hand or right-hand side
of the product in an adjacent cabinet. Refer to ‘Cabinetry preparation’ for service access requirements. z The drain hose should not extend more than 13ft (4m). A longer drain hose will cause reduced performance.

Water connection z The dishwasher should not be connected to a water system where there
is no temperature control, unless the system is fitted with a suitable tempering valve. z The dishwasher must not be connected to an undersink high- pressure push-through hot water system, as damage to the system will result. z Maximum water temperature: 140°F (60°C). z Recommended water temperature: 120°F (50°C) z 3/4″ BSP connection to product inlet valve. z Ensure water connection complies with local plumbing regulations.
Water pressure z 0.03-1MPa
Electrical requirements z 120V, 60Hz, Maximum current 8.9A
Anti-flood protection z This dishwasher has anti-flood protection, which will stop the water
flowing in the event of a leak within the machine.

b c

b c

a

a

SERVICE DIMENSION
A Length of drain hose B Distance from floor to top of hose support C Minimum distance from floor to end of drain hoses
standpipe install illustrated. Distance is the same for all plumbing installs.

LEFT SIDE

INCH

MM

77 15/16

1980

29 1/2 ­34 3/4

750­883

19 11/16

500

RIGHT SIDE

INCH

MM

64 15/16

1650

29 1/2 ­34 3/4

750­883

19 11/16

500

10

z We recommend locating the service holes on either side of the dishwasher as shown.
z If the holes are created through wood, ensure the edges are smooth and rounded.
z If the holes are created through metal, ensure an edge protector is fitted.

SERVICE ACCESS

SERVICE HOLE DIMENSIONS
A Maximum distance between rear of cavity and service hole* B Maximum distance between floor and service hole* C Minimum diameter of service hole
based on a cabinetry depth of 22 13/16″ (580mm) **depending on adjustment of levelling feet

C

A

REAR WALL

B

FLOOR

PROFILE

INCH
9/16 0­2 1 1/2

MM
15 0­50
38

11

UNPACK PRODUCT

CABINETRY PREPARATION

Cut straps, lift carton off product and

Ensure all minimum cabinetry and

1

remove the top cap.

1

service specifications have been met and that all services will be accessible

Dispose of packaging responsibly.

after installation.

Ensure cabinetry floor is free from

2

Remove the install kit, any internal packaging, all rubber bands and all tape.

2

bumps and obstructions that could prevent the dishwasher from sliding into

the cavity.

Align the supplied moisture protection

tape to the cabinetry as shown.

3

Ensure this area is free of debris

before carefully applying the tape to

the surface.

12

SERVICES PREPARATION

Flush water line into a bucket.

1

Install a hand shut-off valve in a readily accessible location in the

1

adjacent cabinetry.

Hot water line installations:

2

Carefully route the hot water line through the service hole in the side of

2

the cabinetry.

Route the hard wiring through the

3

service hole in the side of the cabinetry.

3

Tape to the floor to secure.

Remove the toe kick by unscrewing the

4

four screws. Keep aside for re-assembly at the end of

4

the installation.

DOOR PANEL PREP
Ensure door panel meets all specifications.
Using the template as a guide, pre-drill all holes into the panel.
Ensure the sliding bracket is oriented correctly before securing it to the panel.
Loosely fit both 16mm Philips hanging screws onto the door panel. Ensure there is a minimum space of 1/8″ (3mm) between the screw-head and the panel.
13

PUSH INTO CAVITY

ELECTRICAL CONNECTION

1

Using a flat bladed screwdriver, turn to

raise the leveling feet. Level the rear,

outside legs first followed by the front

1

legs. Do not adjust the rear middle

leg yet.

Unscrew and remove the junction box cover to access the terminal block. Do not remove the screw holding the junction box bracket in place.

Remove both screw covers before

Install the strain relief into the junction

partially pushing the product into the

box bracket and secure the house

cavity, pulling the hoses through as you

wiring or the power cord and tighten.

2

push to avoid crushing or twisting them.

2

Thread the wires through the hole in

Take care not to bend the legs.

the junction box bracket and connect

Push the product from the outside

the incoming ground to green, white to

edges to avoid door damage.

white and black to black.

Check the product sits level within

the cavity.

Refit the junction box cover ensuring

To access the rear leg adjustment,

all wires are clear of the cover. Ensure

3

remove the four screws holding the toe kick and mounting plate in place.

3

the power cord is routed under the dishwasher.

If required, the rear middle leg can be adjusted from the front of the product

Ensure product does not have live power until this installation is complete.

using a 6mm Allen key.

Select desired spacer width and cut to size. Remove adhesive and fit two spacers to each side of the product.

4

Push the product into the cavity from the outside edges taking care not to

damage the electrical cable. Guide

the cable through the channel under

the product on the right hand side

if required.

14

INSTALL HARD PLUMBING

Fitting copper pipe:

Slide the compression nut and ferrule

1

towards the end of the pipe. Insert the end of the pipe into the elbow and

1

screw the compression nut to the thread

of the elbow.

Braided hose installations:

Screw the nut of the hose to the thread of the elbow. Hand-tighten then using

2

a spanner or pliers, turn a further 180°

to secure.

Connecting elbow to inlet valve:

Connect a 90° elbow to the water inlet

2

valve. Ensure a rubber gasket is placed between the threads of the elbow and

water supply valve. The end of the elbow

must point to the rear of the dishwasher.

Do not over tighten the elbow.

Briefly turn on the water supply and

3

check for leaks, once you are satisfied the connections will not leak turn off the

water supply.

SECURE DOOR PANEL
Align the door panel to the product. Slot slider bracket and upper screws into place. Slide the panel upwards to lock into place.
Align door panel to surrounding cabinetry. Open door and secure panel to product using 4 x screws.
15

1 2 3 4
16

FIT EXIT VENT

Measure the custom panel overhang

from the base of the inner door. Refer to the table below for the

1

recommended cut location.

CUT LOCATION
0 1 2 3 4 5 6 7 8 9 !0 !1 !2 !3

OVERHANG (INCH) 0 0 0­3/16 3/16­1/2 1/2­3/4 13/16­1
1 1/16­1 5/16 1 5/16­1 9/16 1 5/8­1 7/8 1 7/8­2 1/8 2 3/16­2 3/8 2 7/16­2 11/16 2 3/4­2 15/16
–

OVERHANG (MM) 0 0 0­5 5­12 13­19 20­26 27­33 34­40 41­47 48­54 55­61 62­68 69­75 –

2

On a protected surface, carefully cut the vent at the desired location.

Slot the exit vent into the product and secure using two 3.5x11mm screws.

BALANCE DOOR
Use a 4mm Allen key to adjust the door tension. Rotate clockwise to increase tension, rotate counterclockwise to decrease tension. Ensure both sides are adjusted evenly.
Open the door at a 45° angle and ensure it holds. If the door does not stay open, repeat the above step.

SECURE TO CAVITY

PLUMBING & ELECTRICAL CONNECTION Ø1 1/2″ (38MM) STANDPIPE INSTALLATION

1

Loosely fit 2 x side fixing screws.

Install the drain hose support to the

back wall, as close to the underside of

1

the countertop as possible. Refer to

‘Plumbing & electrical considerations’ for

minimum install heights.

If needed, adjust the dishwasher within

2

the cavity before tightly securing in

Pull the hose through the support guide and rest in standpipe.

place. Replace the screw covers.

2

Ensure the drain hose does not extend into water retained in the trap; an air gap

is required to prevent waste water from

siphoning back into the tub.

Connect the inlet hose to tap and

handtighten into place. Using a spanner

3

Secure to benchtop using 2 x screws

if possible.

3

or pliers, turn a further 180° to secure. Avoiding over tightening.

Do not turn water supply on. The

dishwasher must be powered on for the

flood protection feature to be enabled.

4

Plug product in. Non-hardwired installs only.

17

PLUMBING & ELECTRICAL CONNECTION

SINK TRAP/WASTE TEE INSTALLATION

SINGLE AIR GAP INSTALLATION

Install the drain hose support to the

1

back wall, as close to the underside of

the countertop as possible. Refer to

1

‘Plumbing & electrical considerations’ for

Install your single Air Gap Kit to the benchtop like shown.

minimum install heights.

Pull the hose through the drain hose

Thread wire clip on to the hose before

support before threading the hose

fitting hose to the supplied hose joiner.

clamp onto the hose and fitting to

Secure using the hose clamps. Fit to

2

the sink trap. Secure to trap using the clamp. Ensure hose is routed straight to

2

the Air Gap Kit. Ensure hose is routed straight to the joiner, remove any excess

the trap.

drain hose.

Unplug or drill out the waste tee before securing joiner to sink trap or waste tee.

Unplug or drill out the waste tee before securing to sink trap or waste tee.

Ensure the rubber washer is fitted when

connecting the inlet hose to the tap.

Connect the inlet hose to tap and

Hand-tighten into place.

handtighten into place. Using a spanner

or pliers, turn a further 180° to secure.

3

Using a spanner or pliers, turn a further 180° to secure. Avoiding over- tightening.

3

Avoiding over tightening.

Do not turn water supply on. The

Do not turn water supply on. The

dishwasher must be powered on for the

dishwasher must be powered on for the

flood protection feature to be enabled.

flood protection feature to be enabled.

4

Plug product in. Non-hardwired installs only.

4

Plug product in. Non-hardwired installs only.

18

INSTALLER CHECKLIST

TO BE COMPLETED BY THE INSTALLER

Installation

Check all parts are installed correctly and are secure.

Ensure all packaging, tape and rubberbands have been removed.

1

Ensure all clearance gaps have been maintained.

Ensure dishwasher is securely fastened to the cabinetry and door opens and closes
freely with no resistance.

Ensure panel is fitted correctly to the dishwasher Check the spray arm is in place, mounted correctly and rotates freely.

Plumbing

Ensure any knock-outs or plugs in drain connection have been drilled out and drain

2

connection has been made.

The drain hose joiner must not support the weight of excess hose material. Keep drain
hose as fully extended as possible to prevent sagging. Any excess length of drain hose should be kept on the dishwasher side of the drain hose support.

Ensure inlet hose has supplied rubber washer fitted, and that it is tightened.

If connecting the drain hose to the sink trap, ensure the highloop is a minimum 150mm
higher than the drain hose joiner.

Water softener models: adjust the water softener setting from the default setting to suit
the water hardness of the area. Refer to your user guide.

3

Ensure water supply is turned off until power is connected and turned on. The
dishwasher must be powered on for the flood protection feature to be enabled.

Check for leaks.

Electrical
Ensure all electrical tests have been conducted in accordance with local regulations. Ensure metal toe kick plate has been re-fitted. If site is left without power after installation is complete, ensure water supply is
turned off to prevent flooding.

TEST OPERATION
Turn power and water supply on and open the dishwasher.
Select RINSE.
After the RINSE cycle has finished, ensure the dishwasher has run and drained correctly.
19

INSTALL METAL PLATE TOE KICK

INSTALL CONTINUOUS TOE KICK

Refit the toe kick and mounting

plate panels.

1

Slide the back of the mounting plate

1

Align toe kick to product and ensure all door swing clearances have been met.

up or down to conceal any gaps left

between the product and floor.

INSTALL SOUND SEAL
2

Align both sound seal sheets to the

1

base of the dishwasher. If required, trim

excess felt.

Fit panel to surrounding cabinetry

Ensure door swing is unobstructed

before securing the sound seal sheets

2

to the metal toe kick plate using the supplied double sided tape.

Ensure mounting screws are accessible through the sound seal after fitting.

20

FISHERPAYKEL.COM
© Fisher & Paykel Appliances 2023. All rights reserved. The models shown in this guide may not be available in all markets
and are subject to change at any time. The product specifications in this guide apply to the specific products and models described at the date of issue. Under our policy of continuous product
improvement, these specifications may change at any time. For current details about model and specification availability in your country,
please go to our website or contact your local Fisher & Paykel dealer.
592981C 12.23

References

• Shop Luxury Kitchen & Home Appliances | Fisher & Paykel United Kingdom
• Shop Luxury Kitchen & Home Appliances | Fisher & Paykel USA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>